IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The power-up GMSL link configuration is controlled by the HIM and BWS
pins, whose state is reflected in register 0x1c. Print the detected
power-up config in a debug message to help debugging.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
GMSL can transport three synchronization signals: VSync, HSync and Data
Enable. The MAX9286 can select either HS or DE as a line valid signal.
Not all serializers (and transmission formats) support the DE signal.
The MAX9271, used by the RDACM20 and RDACM21 cameras, doesn't document
DE support. Nonetheless, the max9286 driver selects the DE signal as
line valid in register 0x0c (by not setting the DESEL bit). It's not
clear why this works. As HS is a more common line valid qualifier, set
the DESEL bit by default. This is needed to support the onsemi MARS
cameras.
If a camera requires usage of the DE signal in the future, this will
need to be made configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org> # On Eagle V3M with RDACM20
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GMSL serial data bus width is normally selected through the BWS pin.
On some systems, the pin may not be wired to the correct value. Support
overriding the bus width by software, using the value specified in the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Read the maxim,i2c-clock-frequency DT property that specifies the speed
of the remote I2C bus, and configure the MAX9286 accordingly. The remote
serializers must all have a matching configuration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for 12-bit raw bayer formats to the driver, configuring the
GMSL format accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286_DATATYPE_RAW11 value is used to configure the MAX9286 for
11-bit or 12-bit input data. While 11-bit data is supported on the GMSL
side, CSI-2 doesn't have a RAW11 format. 11-bit data is transferred over
CSI-2 as RAW12. Rename the macro accordingly to avoid confusion.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286 can generate a framesync signal to synchronize the cameras,
using an internal timer. Support this mode of operation and configure it
through the .s_frameinterval() operation. If the frame interval is not
0, framesync is switched to manual mode with the specified interval,
otherwise automatic mode is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow users to use one PoC regulator per port, instead of a global
regulator.
The properties '^port[0-3]-poc-supply$' in the DT node are used to
indicate the regulators for individual ports.
Signed-off-by: Thomas Nizan <tnizan@witekio.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----
iJgEABYKAEAWIQTAnvhxs4J7QT+XHKnMPy2AAyfeZAUCY8R0CCIcbGF1cmVudC5w
aW5jaGFydEBpZGVhc29uYm9hcmQuY29tAAoJEMw/LYADJ95k3XwBAMn3MAcX185i
DNPc1tWKCA0+j7eLqgCrNHOQgqYSV7ZOAQDaoDt/drJffp8S9TdCpP1DhT9wcSIB
i6i6j7mlzGsqBw==
=yAlT
-----END PGP SIGNATURE-----
Merge tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux into media_stage
uvcvideo fixes and improvements
* tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux: (27 commits)
media: uvcvideo: Silence memcpy() run-time false positive warnings
media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910
media: uvcvideo: Fix race condition with usb_kill_urb
media: uvcvideo: Use standard names for menus
media: uvcvideo: Fix power line control for Lenovo Integrated Camera
media: uvcvideo: Refactor power_line_frequency_controls_limited
media: uvcvideo: Refactor uvc_ctrl_mappings_uvcXX
media: uvcvideo: Implement mask for V4L2_CTRL_TYPE_MENU
media: uvcvideo: Extend documentation of uvc_video_clock_decode()
media: uvcvideo: Limit power line control for Acer EasyCamera
media: uvcvideo: Refactor __uvc_ctrl_add_mapping
media: uvcvideo: Fix handling on Bitmask controls
media: uvcvideo: Do not return positive errors in uvc_query_ctrl()
media: uvcvideo: Return -EACCES for Wrong state error
media: uvcvideo: Improve error logging in uvc_query_ctrl()
media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
media: uvcvideo: Factor out usb_string() calls
media: uvcvideo: Limit power line control for Acer EasyCamera
media: uvcvideo: Recover stalled ElGato devices
media: uvcvideo: Remove void casting for the status endpoint
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since commit 0166dc11be91 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
As a minor optimization, this also lets us drop of_match_ptr(), as we
now know what it will resolve to, we might as well save cpp some work.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
[hverkuil: remove obsolete kerneldoc 'id' documentation]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The memcpy() in uvc_video_decode_meta() intentionally copies across the
length and flags members and into the trailing buf flexible array.
Split the copy so that the compiler can better reason about (the lack
of) buffer overflows here. Avoid the run-time false positive warning:
memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1)
Additionally fix a typo in the documentation for struct uvc_meta_buf.
Reported-by: ionut_n2001@yahoo.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
usb_kill_urb warranties that all the handlers are finished when it
returns, but does not protect against threads that might be handling
asynchronously the urb.
For UVC, the function uvc_ctrl_status_event_async() takes care of
control changes asynchronously.
If the code is executed in the following order:
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_ctrl_status_event_work()
uvc_status_start() -> FAIL
Then uvc_status_start will keep failing and this error will be shown:
<4>[ 5.540139] URB 0000000000000000 submitted while active
drivers/usb/core/urb.c:378 usb_submit_urb+0x4c3/0x528
Let's improve the current situation, by not re-submiting the urb if
we are stopping the status event. Also process the queued work
(if any) during stop.
CPU 0 CPU 1
===== =====
uvc_status_complete()
uvc_status_stop()
uvc_status_start()
uvc_ctrl_status_event_work() -> FAIL
Hopefully, with the usb layer protection this should be enough to cover
all the cases.
Cc: stable@vger.kernel.org
Fixes: e5225c820c05 ("media: uvcvideo: Send a control event when a Control Change interrupt arrives")
Reviewed-by: Yunke Cao <yunkec@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of duplicating the menu info, use the one from the core.
Also, do not use extra memory for 1:1 mappings.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequenyc control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 30c9:0093 Lenovo Integrated Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x30c9
idProduct 0x0093
bcdDevice 0.07
iManufacturer 3 Lenovo
iProduct 1 Integrated Camera
iSerial 2 8SSC21J75356V1SR2830069
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move the control mapping to uvc_ctrl.c. This way we do not have
references to UVC controls or V4L2 controls in uvc_driver.c.
This also fixes a bug introduced in commit 382075604a68 ("media:
uvcvideo: Limit power line control for Quanta UVC Webcam"). The
offending commit caused the power line control menu entries to have
incorrect indices compared to the V4L2_CID_POWER_LINE_FREQUENCY_*
enumeration. Now that the limited mapping reuses the correct menu_info
array, the indices correctly map to the V4L2 control specification.
Fixes: 382075604a68 ("media: uvcvideo: Limit power line control for Quanta UVC Webcam")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Convert the array of structs into an array of pointers, that way the
mappings can be reused.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Replace the count with a mask field that lets us choose not only the max
value, but also the minimum value and what values are valid in between.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make an explicit reference to UVC 1.5, explaining how the algorithm
supports the different behaviour of UVC 1.1 and 1.5.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: HungNien Chen <hn.chen@sunplusit.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Simplify the exit code with a common error tag freeing all the memory.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Minimum and step values for V4L2_CTRL_TYPE_BITMASK controls should be 0.
There is no need to query the camera firmware about this and maybe get
invalid results.
Also value should be masked to the max value advertised by the
hardware.
Finally, handle UVC 1.5 mask controls that use MAX instead of RES to
describe the valid bits.
Fixes v4l2-compliane:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(97): minimum must be 0 for a bitmask control
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
If the returned size of the query does not match the expected size or it
is zero, return -EPIPE instead of 0 or a positive value.
This will avoid confusing the caller (and ultimately userspace) that
doesn't expect a positive or zero value.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Error 2 is defined by UVC as:
Wrong State: The device is in a state that disallows the specific
request. The device will remain in this state until a specific action
from the host or the user is completed.
This is documented as happening when attempting to set the value of a
manual control when the device is in auto mode. While V4L2 allows this,
the closest error code defined by VIDIOC_S_CTRL is EACCES:
EACCES: Attempt to set a read-only control or to get a write-only
control. Or if there is an attempt to set an inactive control and the
driver is not capable of caching the new value until the control is
active again.
Replace EILSEQ with EACCES.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Standard use of the driver may result in error messages on the kernel
log. This can hide other more important messages, and alert
unnecessarily the user. Let's keep dev_err() for the important
occasions.
If __uvc_query_ctrl() failed with a non -EPIPE error, then report that
with dev_err. If an error code is obtained, then report that with
dev_dbg.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Check for inactive controls in uvc_ctrl_is_accessible().
Use the new value for the master_id controls if present, otherwise
use the existing value to determine if it is OK to set the control.
Doing this here avoids attempting to set an inactive control, which
will return an error from the USB device, which returns an invalid
errorcode.
This fixes:
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
warn: v4l2-test-controls.cpp(483): s_ctrl returned EIO
test VIDIOC_G/S_CTRL: OK
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(739): s_ext_ctrls returned EIO
warn: v4l2-test-controls.cpp(816): s_ext_ctrls returned EIO
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
Tested with:
v4l2-ctl -c auto_exposure=1
OK
v4l2-ctl -c exposure_time_absolute=251
OK
v4l2-ctl -c auto_exposure=3
OK
v4l2-ctl -c exposure_time_absolute=251
VIDIOC_S_EXT_CTRLS: failed: Input/output error
exposure_time_absolute: Input/output error
ERROR
v4l2-ctl -c auto_exposure=3,exposure_time_absolute=251,auto_exposure=1
v4l2-ctl -C auto_exposure,exposure_time_absolute
auto_exposure: 1
exposure_time_absolute: 251
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
When parsing UVC descriptors to instantiate entities, the driver calls
usb_string() to retrieve the entity name from the device, and falls back
to a default name if the string can't be retrieved. This code pattern
occurs multiple times. Factor it out to a separate helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Elgato Cam Link 4k can be in a stalled state if the resolution of
the external source has changed while the firmware initializes.
Once in this state, the device is useless until it receives a
USB reset. It has even been observed that the stalled state will
continue even after unplugging the device.
lsusb -v
Bus 002 Device 002: ID 0fd9:0066 Elgato Systems GmbH Cam Link 4K
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 9
idVendor 0x0fd9 Elgato Systems GmbH
idProduct 0x0066
bcdDevice 0.00
iManufacturer 1 Elgato
iProduct 2 Cam Link 4K
iSerial 4 0005AC52FE000
bNumConfigurations 1
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
