IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
MPLS over UDP is supported in hardware by using a packet reformat object
with reformat type equal L3_TUNNEL_TO_L2 which both decapsulates the
outer L3, L4 and MPLS headers, and allows for setting the L2 headers of
the resulting decapsulated packet. For the hardware to operate
correctly, the configuration of the firmware must have
FLEX_PARSER_PROFILE_ENABLE = 1.
Example tc rule:
tc filter add dev bareudp0 protocol all prio 1 root flower enc_dst_port \
6635 enc_src_ip 8.8.8.23 action mpls pop protocol ip pipe \
action pedit ex munge eth dst set 00:11:22:33:44:21 pipe action \
mirred egress redirect dev enp59s0f0_0
We use pedit to set the correct destination MAC.
For MPLS over UDP decapsulation to take place, the driver logic requires
the following:
1. flower filter added on bareudp device.
2. action mpls pop
3. zero or more pedit munge actions
4. one redirect action
Current implementation supports only IPv4 and no VLAN.
tc filter show output looks like this:
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
enc_src_ip 8.8.8.24
enc_dst_port 6635
in_hw in_hw_count 1
action order 1: mpls pop protocol ip pipe
index 2 ref 1 bind 1
action order 2: pedit action pipe keys 2
index 1 ref 1 bind 1
key #0 at eth+0: val 00112233 mask 00000000
key #1 at eth+4: val 44210000 mask 0000ffff
action order 3: mirred (Egress Redirect to device enp59s0f0_0) stolen
index 2 ref 1 bind 1
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support matching on MPLS over UDP parameters using misc2 section of
match parameters.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MPLS over UDP is supported by adding a rule on a representor net device
which does tunnel_key set, push mpls and forward to a baredup device. At
the hardware level we use a packet_reformat_context object to do the
encapsulation of the packet.
The resulting packet looks as follows (left side transmitted first):
outer L2 | outer IP | UDP | MPLS | inner L3 and data |
Example usage:
tc filter add dev $rep0 protocol ip prio 1 root flower skip_sw \
action tunnel_key set src_ip 8.8.8.21 dst_ip 8.8.8.24 id 555 \
dst_port 6635 tos 4 ttl 6 csum action mpls push protocol 0x8847 \
label 555 tc 3 action mirred egress redirect dev bareudp0
This is how the filter is shown with tc filter show:
tc filter show dev enp59s0f0_0 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
skip_sw
in_hw in_hw_count 1
action order 1: tunnel_key set
src_ip 8.8.8.21
dst_ip 8.8.8.24
key_id 555
dst_port 6635
csum
tos 0x4
ttl 6 pipe
index 1 ref 1 bind 1
action order 2: mpls push protocol mpls_uc label 555 tc 3 ttl 255 pipe
index 1 ref 1 bind 1
action order 3: mirred (Egress Redirect to device bareudp0) stolen
index 1 ref 1 bind 1
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to improve code maintainability and readability, introduce new
CONFIG_MLX5_CLS_ACT kconfig variable to control compilation of TC hardware
offloads implementation. This allows distinguishing between features that
require TC support (MPLSoUDP, etc.) and features that just rely on
representor functionality (rep_bond for live migration, etc.).
Modify rep_tc.h, rep_neigh.h, en_tc.h and chains.h files to provide stubs
for functions that are called from generic code.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract TC-specific code from
en_main.c to en_tc.c. This allows easily compiling out the code by
only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_main.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract neigh-specific code
from en_rep.c to standalone file. This allows easily compiling out the code
by only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_rep.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract TC-specific code from
en_rep.c to standalone file. This allows easily compiling out the code by
only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_rep.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use IS_ERR() and PTR_ERR() instead of PTR_ERR_OR_ZERO() to
simplify code, avoid redundant judgements.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".
Fixes: 1f26dac32057 ("[NET]: Add Sun Cassini driver.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_set_ageing_time has 2 callers:
- felix_set_ageing_time: from drivers/net/dsa/ocelot/felix.c
- ocelot_port_attr_ageing_set: from drivers/net/ethernet/mscc/ocelot.c
The issue described in the fixed commit below actually happened for the
felix_set_ageing_time code path only, since ocelot_port_attr_ageing_set
was already dividing by 1000. So to make both paths symmetrical (and to
fix addresses getting aged way too fast on Ocelot), stop dividing by
1000 at caller side altogether.
Fixes: c0d7eccbc761 ("net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa139 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the op-mode for the device is not set in the device tree then set
the strapped op-mode and store it for later configuration.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree may not have the property set for port mirroring
because the hardware may have it strapped. If the property is not in the
DT then check the straps and set the port mirroring bit appropriately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5e3768a436bb70c9c3e27aaba6b73f8ef8f5dcf3.
On request from Russell King, this is a layering violation.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of reload fail, the mlxsw_sp->ports contains a pointer to a
freed memory (either by reload_down() or reload_up() error path).
Fix this by initializing the pointer to NULL and checking it before
dereferencing in split/unsplit/type_set callpaths.
Fixes: 24cc68ad6c46 ("mlxsw: core: Add support for reload")
Reported-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the policer drop counter is retrieved when the jiffies value is
a multiple of 64, the counter will not be incremented.
This randomly breaks a selftest [1] the reads the counter twice and
checks that it was incremented:
```
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
```
Fix by always incrementing the counter by 1.
[1] tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh
Fixes: ad188458d012 ("netdevsim: Add devlink-trap policer support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon adapter hotplug, cxgb4 registers ULD devices for all the ULDs that
are already loaded, ensuring that ULD's can enumerate the hotplugged
adapter without reloading the ULD.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make FLOW_ACTION_HW_STATS_DONT_CARE be all bits, rather than none, so that
drivers and __flow_action_hw_stats_check can use simple bitwise checks.
Pre-fill all actions with DONT_CARE in flow_rule_alloc(), rather than
relying on implicit semantics of zero from kzalloc, so that callers which
don't configure action stats themselves (i.e. netfilter) get the correct
behaviour by default.
Only the kernel's internal API semantics change; the TC uAPI is unaffected.
v4: move DONT_CARE setting to flow_rule_alloc() for robustness and simplicity.
v3: set DONT_CARE in nft and ct offload.
v2: rebased on net-next, removed RFC tags.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc32 and with 895586d5dc32 applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc32, failing: 00200000 40000000
- without 895586d5dc32, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc32, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the driver for the MediaTek STAR Ethernet MAC currently used
on the MT8* SoC family. For now we only support full-duplex.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Makefile formatting in the kernel tree usually doesn't use tabs,
so remove them before we add a second driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll soon by adding a second MediaTek Ethernet driver so modify the
Kconfig prompt.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit reduces the driver load time by using usec resolution
instead of msec when polling for hardware state change.
Also add back-off mechanism to handle cases where minimal sleep
time is not enough.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use BIT macro instead of shift operator for code clarity
2. Replace multiple flag assignments to a single assignment of multiple
flags in ena_com_add_single_rx_desc()
3. Move ENA_HASH_KEY_SIZE from ena_netdev.h to ena_com.h
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add leading and trailing spaces to several comments for better
readability
2. Make tabs and spaces uniform in enum defines in ena_admin_defs.h
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Reorder sanity checks in get_comp_ctxt() to make more sense
2. Reorder variables in ena_com_fill_hash_function() and
ena_calc_io_queue_size() in reverse christmas tree.
3. Move around member initializations.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove unused definition of DRV_MODULE_VERSION
2. Remove {} from single line-of-code ifs
3. Remove unnecessary comments from ena_get/set_coalesce()
4. Remove unnecessary extra spaces and newlines
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Join unnecessarily broken short lines in ena_com.c ena_netdev.c
2. Fix Indentations of broken lines
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix spelling and grammar mistakes in comments in ena_com.h,
ena_com.c and ena_netdev.c
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all types of variables that convey the number and sizeof queues to
be u32, for consistency with the API between the driver and device via
ena_admin_defs.h:ena_admin_get_feat_resp.max_queue_ext fields. Current
code sometimes uses int and there are multiple assignments between these
variables with different types.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ena_update_tx/rx_rings_intr_moderation() to
ena_update_tx/rx_rings_nonadaptive_intr_moderation()
to distinguish between adaptive and non adaptive interrupt moderaion.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize prev_intr_delay_resolution with ena_dev->intr_delay_resolution
unconditionally, since it is initialized with
ENA_DEFAULT_INTR_DELAY_RESOLUTION in ena_probe(). This approach makes much
more sense than handling errors of not initializing it.
Also added unlikely to if condition.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default return value should be -EINVAL since the input
in this case was unexpected.
Also remove the now redundant check in the beginning
of the function.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use u64 instead of unsigned long long for clarity
Signed-off-by: Shai Brandes <shaibran@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ena_com_free_desc to ena_com_free_q_entries to match
the LLQ mode.
In non-LLQ mode, an entry in an IO ring corresponds to a
a descriptor. In LLQ mode an entry may correspond to several
descriptors (per LLQ definition).
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer ENA devices can write data to rx buffers with an offset
from the beginning of the buffer.
This commit adds support for this feature in the driver.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an inconsistency between code and spec, which
was found while working on the QoS implementation.
When 8TCs are used, 2 is the maximum supported number of index bits.
In a 4TC mode, we do support 3, but we shouldn't really use the bytes,
which are intended for the 8TC mode.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mqprio min_rate limiters.
A2 HW supports Weighted Strict Priority (WSP) arbitration for Tx Descriptor
Queue scheduling among TCs, which can be used for min_rate shaping.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the order of arguments for TC weight/credit setter
functions.
Having the "value to be set" on the right is slightly more robust in
a sense that it's more natural for the humans, so it's a bit more
error-proof this way.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the TC-queue mapping mechanism used on A2.
Configure the A2 HW in such a way that we can keep queue index mapping
exactly as it was on A1.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for automatic queue number downgrade.
On A2: this is a must have, because only TC0/TC1 support more than 4Q.
Other TCs support 4Qs maximum.
Thus, on A2 we must downgrade the number of queues per TC to 4, if more
than 2 TCs are requested.
On A1: this allows using 8TCs even on systems with cpu count >= 8, when
we have 8 queues by default.
We will just automatically switch to 8TCx4Q mode in this case.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initial support for mqprio rate limiters (max_rate only).
Atlantic HW supports Rate-Shaping for time-sensitive traffic at per
Traffic Class (TC) granularity.
Target rate is defined by:
* nominal link rate (always 10G);
* rate factor (ratio between nominal rate and max allowed).
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates TCVEC2RING to accept nic_cfg, which is needed to be able
to use it from hw_atl.
The name is updated to reflect the changes.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for per-TC queue statistics.
By default (single TC), the output is the same as it used to be, e.g.:
Queue[0] InPackets: 2
Queue[0] OutPackets: 8
Queue[0] Restarts: 0
Queue[0] InJumboPackets: 0
Queue[0] InLroPackets: 0
Queue[0] InErrors: 0
If several TCs are enabled, then each queue statistics line is prefixed
with TC number, e.g.:
TC0 Queue[0] InPackets: 6
TC0 Queue[0] OutPackets: 11
Queue numbering is end-to-end, so:
TC1 Queue[4] InPackets: 0
TC1 Queue[4] OutPackets: 22
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds multi-TC support.
PTP is automatically disabled when the user enables more than 2 TCs,
otherwise traffic on TC2 won't quite work, because it's reserved for PTP.
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following changes:
* add cfg->is_ptp (used for PTP enable/disable switch, which
is described in more details below);
* add cfg->tc_mode (A1 supports 2 HW modes only);
* setup queue to TC mapping based on TC mode on A2;
* remove hw_tx_tc_mode_get / hw_rx_tc_mode_get hw_ops.
In the first generation of our hardware (A1), a whole traffic class is
consumed for PTP handling in FW (FW uses it to send the ptp data and to
send back timestamps).
The 'is_ptp' flag introduced in this patch will be used in to automatically
disable PTP when a conflicting configuration is detected, e.g. when
multiple TCs are enabled.
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the PTP TC initialization into a separate function.
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
