IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
We've found the AUX channel to be less reliable with PCLK_EDP at a
higher rate (typically 25 MHz). This is especially important on systems
with PSR-enabled panels (like Gru-Kevin), since we make heavy, constant
use of AUX.
According to Rockchip, using any rate other than 24 MHz can cause
"problems between syncing the PHY an PCLK", which leads to all sorts of
unreliabilities around register operations.
Fixes: d67a38c5a623 ("arm64: dts: rockchip: move core edp from rk3399-kevin to shared chromebook")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220830131212.v2.1.I98d30623f13b785ca77094d0c0fd4339550553b6@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gru-Bob board does not have a pull-up resistor on its
WLAN_HOST_WAKE# pin, but Kevin does. The production/vendor kernel
specified the pin configuration correctly as a pull-up, but this didn't
get ported correctly to upstream.
This means Bob's WLAN_HOST_WAKE# pin is floating, causing inconsistent
wakeup behavior.
Note that bt_host_wake_l has a similar dynamic, but apparently the
upstream choice was to redundantly configure both internal and external
pull-up on Kevin (see the "Kevin has an external pull up" comment in
rk3399-gru.dtsi). This doesn't cause any functional problem, although
it's perhaps wasteful.
Fixes: 8559bbeeb849 ("arm64: dts: rockchip: add Google Bob")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220822164453.1.I75c57b48b0873766ec993bdfb7bc1e63da5a1637@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the DMC (Dynamic Memory Controller) and the DFI (DDR PHY
Interface) nodes on gru boards so we can support DDR DVFS.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220308110825.v4.12.I3a5c7f21ecd8221b42c2dbcd618386bce7b3e9a6@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dtschema expects PWM node name to be a generic "pwm". This also matches
Devicetree specification requirements about generic node names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220214081916.162014-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It's convenient to get nice names for GPIOs. In particular, Chrome OS
tooling looks for "AP_FLASH_WP" and "AP_FLASH_WP_L". The rest are
provided for convenience.
Gru-Bob and Gru-Kevin share the gru-chromebook.dtsi, and for the most
part they share pin meanings. I omitted a few areas where components
were available only on one or the other.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210820133829.1.Ica46f428de8c3beb600760dbcd63cf879ec24baf@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The cros-ec-extcon has no reg property so remove the unit address from
the DT node to make DT compiler happy.
While here, remove the inexistent extcon-cells property from the extcon
nodes.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200207141324.3188898-1-enric.balletbo@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently, we don't coordinate BT USB activity with our handling of the
BT out-of-band wake pin, and instead just use gpio-keys. That causes
problems because we have no way of distinguishing wake activity due to a
BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
mask before suspend). This can cause spurious wake events just because
we, for instance, try to reconfigure the host controller's event mask
before suspending.
We can avoid these synchronization problems by handling the BT wake pin
directly in the btusb driver -- for all activity up until BT controller
suspend(), we simply listen to normal USB activity (e.g., to know the
difference between device and host activity); once we're really ready to
suspend the host controller, there should be no more host activity, and
only *then* do we unmask the GPIO interrupt.
This is already supported by btusb; we just need to describe the wake
pin in the right node.
We list 2 compatible properties, since both PID/VID pairs show up on
Scarlet devices, and they're both essentially identical QCA6174A-based
modules.
Also note that the polarity was wrong before: Qualcomm implemented WAKE
as active high, not active low. We only got away with this because
gpio-keys always reconfigured us as bi-directional edge-triggered.
Finally, we have an external pull-up and a level-shifter on this line
(we didn't notice Qualcomm's polarity in the initial design), so we
can't do pull-down. Switch to pull-none.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After commit 88ba95bedb79 ("backlight: pwm_bl: Compute brightness of LED
linearly to human eye") the pwm_bl driver is able to calculate a default
brightness table. The calculated table for this PWM will have more
granularity and will be adjusted to change the brightness linearly to
the human eye. Use that table instead of have a DT-defined table with
less granularity.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Bob needs the same backlight and core edp settings, so move these nodes to
the shared dtsi that both will use as a base.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to rk3288-Veyron before, the Gru-series does contain Chromebook
(aka clamshell laptops) and non-Chromebook devices. And while the two
Chromebook devices Kevin and Bob are quite similar, Scarlet the tablet-
device is quite different in its design.
Therefore move the Chromebook parts into a gru-chromebook dtsi file
to make sharing easier.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
