IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.
To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.
This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.
One case where we hit this issue is camera sensors such as e.g. the OV8865
sensor found on the Microsoft Surface Go. The sensor uses clks, regulators
and GPIOs provided by a TPS68470 PMIC which is described in an INT3472
ACPI device. There is special platform code handling this and setting
platform_data with the necessary consumer info on the MFD cells
instantiated for the PMIC under: drivers/platform/x86/intel/int3472.
For this to work properly the ov8865 driver must not bind to the I2C-client
for the OV8865 sensor until after the TPS68470 PMIC gpio, regulator and
clk MFD cells have all been fully setup.
The OV8865 on the Microsoft Surface Go is just one example, all X86
devices using the Intel IPU3 camera block found on recent Intel SoCs
have similar issues where there is an INT3472 HID ACPI-device, which
describes the clks and regulators, and the driver for this INT3472 device
must be fully initialized before the sensor driver (any sensor driver)
binds for things to work properly.
On these devices the ACPI nodes describing the sensors all have a _DEP
dependency on the matching INT3472 ACPI device (there is one per sensor).
This allows solving the probe-ordering problem by delaying the enumeration
(instantiation of the I2C-client in the ov8865 example) of ACPI-devices
which have a _DEP dependency on an INT3472 device.
The new acpi_dev_ready_for_enumeration() helper used for this is also
exported because for devices, which have the enumeration_by_parent flag
set, the parent-driver will do its own scan of child ACPI devices and
it will try to enumerate those during its probe(). Code doing this such
as e.g. the i2c-core-acpi.c code must call this new helper to ensure
that it too delays the enumeration until all the _DEP dependencies are
met on devices which have the new honor_deps flag set.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-2-hdegoede@redhat.com
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3.
No need to flush the caches during hibernation (S4).
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Theoretically, when the hardware signature in FACS changes, the OS
is supposed to gracefully decline to attempt to resume from S4:
"If the signature has changed, OSPM will not restore the system
context and can boot from scratch"
In practice, Windows doesn't do this and many laptop vendors do allow
the signature to change especially when docking/undocking, so it would
be a bad idea to simply comply with the specification by default in the
general case.
However, there are use cases where we do want the compliant behaviour
and we know it's safe. Specifically, when resuming virtual machines where
we know the hypervisor has changed sufficiently that resume will fail.
We really want to be able to *tell* the guest kernel not to try, so it
boots cleanly and doesn't just crash. This patch provides a way to opt
in to the spec-compliant behaviour on the command line.
A follow-up patch may do this automatically for certain "known good"
machines based on a DMI match, or perhaps just for all hypervisor
guests since there's no good reason a hypervisor would change the
hardware_signature that it exposes to guests *unless* it wants them
to obey the ACPI specification.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some devices with a X-Powers AXP288 PMIC the LPAT tables in the ACPI
node for the AXP288 PMIC for some reason only describe a small temperature
range, e.g. 27° - 37° Celcius (assuming the entries are in millidegrees).
When the tablet is idle in a room at 21° degrees this is causing values
outside the LPAT table to be read, causing e.g. the following 2 errors
to get spammed to the logs every 4 seconds! :
[ 7512.791316] ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] (20210930/evregion-281)
[ 7512.791611] ACPI Error: Aborting method \_SB.SXP1._TMP due to previous error (AE_ERROR) (20210930/psparse-529)
Fix this by clamping the raw value to the LPAT table range before
passing it to acpi_lpat_raw_to_temp().
Note clamping has been chosen rather then extrapolating because it is
unknown how other parts of the ACPI tables will respond to temperature
values outside of the LPAT range.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The LPAT tables used in the DSDT for some PMICs require special handling,
allow the PMIC OpRegion drivers to provide an alternative implementation
by adding a lpat_raw_to_temp function pointer to struct pmic_table;
and initialize this to the default acpi_lpat_raw_to_temp function
for all PMICs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The struct intel_pmic_opregion_data declarations never change,
constify them all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using write_support=1 with the ec_sys module changes the mode of the
"io" debugfs file to 0600. This will cause any attempts to access it under
a kernel in lockdown mode to return -EPERM, which makes the entire ec_sys
module unusable.
Use the special module_param_hw() macro for module parameters which
may not be used while in lockdown mode, to avoid this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move acpi_ec_create_query() after acpi_ec_event_processor(), drop the
no longer needed forward declaration of the latter, and eliminate
acpi_ec_delete_query() which isn't really necessary.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EC driver uses a relatively simple state machine for the event
work handling, but it is not really straightforward to figure out.
The states are as follows:
"Ready": The event handling work can be submitted.
In this state, the EC_FLAGS_QUERY_PENDING flag is clear.
"In progress": The event handling work is pending or is being
processed. It cannot be submitted again.
In ths state, the EC_FLAGS_QUERY_PENDING flag is set and both the
events_to_process count is nonzero and the EC_FLAGS_QUERY_GUARDING
flag is clear.
"Complete": The event handling work has been completed, but it still
cannot be submitted again.
In ths state, the EC_FLAGS_QUERY_PENDING flag is set and the
events_to_process count is zero or the EC_FLAGS_QUERY_GUARDING
flag is set.
The state changes from "Ready" to "In progress" when new event is
detected by advance_transaction() and acpi_ec_submit_event() is
called by it.
Next, the state can change from "In progress" directly to "Ready" in
the following situations:
* ec_event_clearing is ACPI_EC_EVT_TIMING_STATUS and the state of
an ACPI_EC_COMMAND_QUERY transaction becomes ACPI_EC_COMMAND_POLL.
* ec_event_clearing is ACPI_EC_EVT_TIMING_QUERY and the state of
an ACPI_EC_COMMAND_QUERY transaction becomes
ACPI_EC_COMMAND_COMPLETE.
* ec_event_clearing is either ACPI_EC_EVT_TIMING_STATUS or
ACPI_EC_EVT_TIMING_QUERY and there are no more events to
process (ie. ec->events_to_process becomes 0).
If ec_event_clearing is ACPI_EC_EVT_TIMING_EVENT, however, the
state must change from "In progress" to "Complete" before it
can change to "Ready". The changes from "In progress" to
"Complete" in that case occur in the following situations:
* The state of an ACPI_EC_COMMAND_QUERY transaction becomes
ACPI_EC_COMMAND_COMPLETE.
* There are no more events to process (ie. ec->events_to_process
becomes 0).
Finally, the state changes from "Complete" to "Ready" when
advance_transaction() is invoked when the state is "Complete" and
the state of the current transaction is not ACPI_EC_COMMAND_POLL.
To make this state machine visible in the code, add a new
event_state field to struct acpi_ec and modify the code to use
it istead the EC_FLAGS_QUERY_PENDING and EC_FLAGS_QUERY_GUARDING
flags.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that it is not necessary to queue up the event work again
if the while () loop in acpi_ec_event_handler() is still running
which is the case if nr_pending_queries is greater than 0 at the
beginning of acpi_ec_submit_event() and modify the code to avoid
doing that.
While at it, rename nr_pending_queries in struct acpi_ec to
events_to_process which actually matches the role of that field
and change its data type to unsigned int which is sufficient.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename acpi_ec_submit_query() to acpi_ec_submit_event(),
acpi_ec_query() to acpi_ec_submit_query(), and
acpi_ec_complete_query() to acpi_ec_close_event() to make
the names reflect what the functions do.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because acpi_ec_event_handler() is a work function, it always
runs in process context with interrupts enabled, so it can use
spin_lock_irq() and spin_unlock_irq() for the locking.
Make it do so and adjust white space around those calls.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is not necessary to check ec->nr_pending_queries against 0 in the
while () loop in acpi_ec_event_handler(), because that loop terminates
when ec->nr_pending_queries is 0 and the code depending on that can be
run after the loop has ended.
Modify the code accordingly and while at it rewrite the comment
regarding that code to make it clearer.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because acpi_ec_event_handler() is the only caller of
acpi_ec_check_event() and the separation of these two functions
makes it harder to follow the code flow, fold the latter into the
former (and simplify that code while at it).
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that the second argument to acpi_ec_query() is redundant,
because in the only case when it is not NULL, the value passed
through it is only checked against 0 and it can only be 0 when
acpi_ec_query() returns an error code, but its return value
is checked along with the value passed through its second
argument.
Accordingly, modify acpi_ec_query() to take only one argument
and while at it, change its handling of the case when
acpi_ec_transaction() returns an error so as to return that
error value to the caller right away.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calling acpi_dispatch_gpe() from acpi_ec_dispatch_gpe() is generally
problematic, because it may cause the spurious interrupt handling in
advance_transaction() to trigger in theory.
However, instead of calling acpi_dispatch_gpe() to dispatch the EC
GPE, acpi_ec_dispatch_gpe() can call advance_transaction() directly
on first_ec and it can pass 'false' as its second argument to indicate
calling it from process context.
Moreover, if advance_transaction() is modified to return a bool value
indicating whether or not the EC work needs to be flushed, it can be
used to avoid unnecessary EC work flushing in acpi_ec_dispatch_gpe(),
so change the code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The flushing of pending work in the EC driver uses drain_workqueue()
to flush the event handling work that can requeue itself via
advance_transaction(), but this is problematic, because that
work may also be requeued from the query workqueue.
Namely, if an EC transaction is carried out during the execution of
a query handler, it involves calling advance_transaction() which
may queue up the event handling work again. This causes the kernel
to complain about attempts to add a work item to the EC event
workqueue while it is being drained and worst-case it may cause a
valid event to be skipped.
To avoid this problem, introduce two new counters, events_in_progress
and queries_in_progress, incremented when a work item is queued on
the event workqueue or the query workqueue, respectively, and
decremented at the end of the corresponding work function, and make
acpi_ec_dispatch_gpe() the workqueues in a loop until the both of
these counters are zero (or system wakeup is pending) instead of
calling acpi_ec_flush_work().
At the same time, change __acpi_ec_flush_work() to call
flush_workqueue() instead of drain_workqueue() to flush the event
workqueue.
While at it, use the observation that the work item queued in
acpi_ec_query() cannot be pending at that time, because it is used
only once, to simplify the code in there.
Additionally, clean up a comment in acpi_ec_query() and adjust white
space in acpi_ec_event_processor().
Fixes: f0ac20c3f613 ("ACPI: EC: Fix flushing of pending work")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Xiaomi Mi Pad 2 has backlit LEDs behind the capacitive menu, home
and back buttons below the screen which are controlled by the PWM2
controller of the CHT SoC. This PWM2 controller gets hidden by the
firmware, add it to the always_present_ids table so that we can use
the PWM controller to control the backlighting of the buttons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GPD win and its sibling the GPD pocket (99% the same electronics in a
different case) use a PCI wifi card. But the ACPI tables on both variants
contain a bug where the SDIO MMC controller for SDIO wifi cards is enabled
despite this. This SDIO MMC controller has a PCI0.SDHB.BRC1 child-device
which _PS3 method sets a GPIO causing the PCI wifi card to turn off.
At the moment there is a pretty ugly kludge in the sdhci-acpi.c code,
just to work around the bug in the DSDT of this single design. This can
be solved cleaner/simply with a quirk overriding the _STA return of the
broken PCI0.SDHB.BRC1 PCI0.SDHB.BRC1 child with a status value of 0,
so that its power_manageable flag gets cleared, avoiding this problem.
Note that even though it is not used, the _STA method for the MMC
controller is deliberately not overridden. If the status of the MMC
controller were forced to 0 it would never get suspended, which would
cause these mini-laptops to not reach S0i3 level when suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Not all ACPI-devices have a HID + UID, allow specifying quirks for
acpi_device_override_status() by path too.
Note this moves the path/HID+UID check to after the CPU + DMI checks
since the path lookup is somewhat costly.
This way this lookup is only done on devices where the other checks
match.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, acpi_bus_get_status() calls acpi_device_always_present() to
allow platform quirks to override the _STA return to report that a
device is present (status = ACPI_STA_DEFAULT) independent of the _STA
return.
In some cases it might also be useful to have the opposite functionality
and have a platform quirk which marks a device as not present (status = 0)
to work around ACPI table bugs.
Change acpi_device_always_present() into a more generic
acpi_device_override_status() function to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It turns out that there is a WMI object which controls the PWM2 device
used for the keyboard backlight and that WMI object also provides some
other useful functionality.
The upcoming lenovo-yogabook-wmi driver will offer both backlight
control and the other functionality, so there no longer is a need
to have the lpss-pwm driver binding to PWM2 for backlight control;
and this is now actually undesirable because this will cause both
the WMI code and the lpss-pwm driver to poke at the same PWM
controller.
Drop the always-present quirk for the PWM2 ACPI-device, so that the
lpss-pwm controller will no longer bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
Section 6.1.2 of ACPI 6.4 explicitly requires _HID to be present for
_CID to be defined, so don't add device IDs from _CID to the device
IDs list of a device if _HID is not valid.
Link: https://uefi.org/specs/ACPI/6.4/06_Device_Configuration/Device_Configuration.html#cid-compatible-id
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Address the following coccicheck warning:
./drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:914:40-41:
WARNING opportunity for swap().
by using swap() for the swapping of variable values and drop
the tmp variable that is not needed any more.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
[ rjw: Subject and changelog rewrite ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a comment in dptf_pch_fivr.c which seemingly was added under
the assumption that the PCH FIVR driver would be used on Tiger Lake
platforms, but support for Alder Lake has been udded to it by commit
38748bcb940e ("ACPI: DPTF: Support Alder Lake"), so update the
comment to cover a broader range of platforms by changing the device
ID mentioned by it to INTC10xx.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
[ rjw: Subject and changelog rewrite ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Print additional debug messages when enabling and disabling wakeup
power for an ACPI device object to facilitate more fine-grained
debugging of problems in that area.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check cpc_desc against NULL in cppc_get_perf(), so it doesn't crash
down the road if cpc_desc is NULL.
Fixes: 0654cf05d17b ("ACPI: CPPC: Introduce cppc_get_nominal_perf()")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
acpi_node_get_parent() isn't used outside drivers/acpi/property.c.
Make it local.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Printk modifier %pfw is used to print the full path of the device name.
This is obtained device by device until a device no longer has a parent.
On ACPI getting the parent fwnode is done by calling acpi_get_parent()
which tries to down() a semaphore. But local IRQs are now disabled in
vprintk_store() before the mutex is acquired. This is obviously a problem.
Luckily struct device, embedded in struct acpi_device, has a parent field
already. Use that field to get the parent instead of relying on
acpi_get_parent().
Fixes: 3bd32d6a2ee6 ("lib/vsprintf: Add %pfw conversion specifier for printing fwnode names")
Cc: 5.5+ <stable@vger.kernel.org> # 5.5+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit c10383e8ddf4 ("ACPI: scan: Release PM resources blocked
by unused objects"), because it causes boot issues to appear on some
platforms.
Reported-by: Kyle D. Pelton <kyle.d.pelton@intel.com>
Reported-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Address of a field inside a struct can't possibly be null; gcc-12 warns
about this.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SGX EPC pages do not have a "struct page" associated with them so the
pfn_valid() sanity check fails and results in a warning message to
the console.
Add an additional check to skip the warning if the address of the error
is in an SGX EPC page.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lkml.kernel.org/r/20211026220050.697075-8-tony.luck@intel.com
SGX reserved memory does not appear in the standard address maps.
Add hook to call into the SGX code to check if an address is located
in SGX memory.
There are other challenges in injecting errors into SGX. Update the
documentation with a sequence of operations to inject.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lkml.kernel.org/r/20211026220050.697075-7-tony.luck@intel.com
During NUMA init, CXL memory defined in the SRAT Memory Affinity
subtable may be assigned to a NUMA node. Since there is no
requirement that the SRAT be comprehensive for CXL memory another
mechanism is needed to assign NUMA nodes to CXL memory not identified
in the SRAT.
Use the CXL Fixed Memory Window Structure (CFMWS) of the ACPI CXL
Early Discovery Table (CEDT) to find all CXL memory ranges.
Create a NUMA node for each CFMWS that is not already assigned to
a NUMA node. Add a memblk attaching its host physical address
range to the node.
Note that these ranges may not actually map any memory at boot time.
They may describe persistent capacity or may be present to enable
hot-plug.
Consumers can use phys_to_target_node() to discover the NUMA node.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/163553711933.2509508.2203471175679990.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for drivers reusing the core table parsing
infrastructure, arrange for handlers to take a context argument. This
allows driver table parsing to wrap ACPI table entries in
driver-specific data.
The first consumer of this infrastructure is the CEDT parsing that
happens in the cxl_acpi driver, add a conditional
(CONFIG_ACPI_TABLE_LIB=y) export of a acpi_table_parse_cedt() helper for
this case.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Tested-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/163553710257.2509508.14310494417463866020.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The CEDT adds yet one more unique subtable header type where the length
is a 16-bit value. Extend the subtable helpers to detect this scenario.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Tested-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/163553709742.2509508.5177761945441327574.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The NFIT driver and now the CXL ACPI driver have both open-coded ACPI
table parsing. Before another instance is added arrange for the core
ACPI sub-table parsing to be optionally available to drivers via the
CONFIG_ACPI_TABLE_LIB symbol. If no drivers select the symbol then the
infrastructure reverts back to being tagged __init via the
__init_or_acpilib annotation.
For now, only tag the core sub-table routines and data that the CEDT parsing in
the cxl_acpi driver would want to reuse, a CEDT parsing helper is added
in a later change.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Alison Schofield <alison.schofield@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/163553709227.2509508.8215196520233473814.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Add support for new ACPI device configuration object called _DSC
to allow certain devices to be probed without changing their power
states, document it and make two drivers use it (Sakari Ailus,
Rajmohan Mani).
- Fix device wakeup power reference counting broken recently by
mistake (Rafael Wysocki).
- Drop unused symbol and macros depending on it from acgcc.h (Rafael
Wysocki).
- Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).
- Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
piece of data from all of the list entries (Hans de Goede).
- Fix register read accesses handling in the Intel PMIC operation
region driver (Hans de Goede).
- Clean up static variables initialization in the EC driver
(wangzhitong).
-----BEGIN PGP SIGNATURE-----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=k8+T
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add support for a new ACPI device configuration object called
_DSC, fix some issues including one recent regression, add two new
items to quirk lists and clean up assorted pieces of code.
Specifics:
- Add support for new ACPI device configuration object called _DSC
("Deepest State for Configuration") to allow certain devices to be
probed without changing their power states, document it and make
two drivers use it (Sakari Ailus, Rajmohan Mani).
- Fix device wakeup power reference counting broken recently by
mistake (Rafael Wysocki).
- Drop unused symbol and macros depending on it from acgcc.h (Rafael
Wysocki).
- Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).
- Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
piece of data from all of the list entries (Hans de Goede).
- Fix register read accesses handling in the Intel PMIC operation
region driver (Hans de Goede).
- Clean up static variables initialization in the EC driver
(wangzhitong)"
* tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: ACPI: Fix non-D0 probe _DSC object example
ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
ACPI: PM: Fix device wakeup power reference counting error
ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
ACPI: EC: Remove initialization of static variables to false
ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
at24: Support probing while in non-zero ACPI D state
media: i2c: imx319: Support device probe in non-zero ACPI D state
ACPI: Add a convenience function to tell a device is in D0 state
Documentation: ACPI: Document _DSC object usage for enum power state
i2c: Allow an ACPI driver to manage the device's power state during probe
ACPI: scan: Obtain device's desired enumeration power state
Merge assorted fixes and cleanups and one new backlight quirk list
item for 5.16-rc1.
* acpica:
ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
* acpi-ec:
ACPI: EC: Remove initialization of static variables to false
ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
* acpi-pmic:
ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
* acpi-video:
ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
Merge new ACPI device configuration object _DSC support for 5.16-rc1.
* acpi-dsc:
Documentation: ACPI: Fix non-D0 probe _DSC object example
at24: Support probing while in non-zero ACPI D state
media: i2c: imx319: Support device probe in non-zero ACPI D state
ACPI: Add a convenience function to tell a device is in D0 state
Documentation: ACPI: Document _DSC object usage for enum power state
i2c: Allow an ACPI driver to manage the device's power state during probe
ACPI: scan: Obtain device's desired enumeration power state
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Fix a device wakeup power reference counting error introduced by
commit a2d7b2e004af ("ACPI: PM: Fix sharing of wakeup power
resources") because of a coding mistake.
Fixes: a2d7b2e004af ("ACPI: PM: Fix sharing of wakeup power resources")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Xiaomi Mi Pad 2 is a Cherry Trail based x86 tablet which does not
use the i915's driver backlight control support:
i915 0000:00:02.0: [drm:intel_panel_setup_backlight [i915]] no backlight present per VBT
Like all Cherry Trail devices the ACPI tables on the Xiaomi Mi Pad 2
contain a broken ACPI-video implementation which causes 6 different
acpi_video backlights to get registered when used.
The lack of the i915 driver registering a BACKLIGHT_RAW (aka native) type
backlight causes acpi_video_get_backlight_type() to pick the broken
acpi_video backlight code as the backlight driver to use.
There actually is a separate lp8556 backlight controller connected
over I2C which gets registered as a BACKLIGHT_PLATFORM (aka vendor).
Add a quirk to force acpi_video_get_backlight_type() to return
acpi_backlight_vendor, so that the broken acpi_video backlight
interfaces do not get registered.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The .ident field of the dmi_system_id structs in the
video_detect_dmi_table[] is not used by the code.
Change all .ident = "..." assignments to comments, this reduces the
size of video_detect.o / video.ko by about 1500 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The handling of PMIC register reads through writing 0 to address 4
of the OpRegion is wrong. Instead of returning the read value
through the value64, which is a no-op for function == ACPI_WRITE calls,
store the value and then on a subsequent function == ACPI_READ with
address == 3 (the address for the value field of the OpRegion)
return the stored value.
This has been tested on a Xiaomi Mi Pad 2 and makes the ACPI battery dev
there mostly functional (unfortunately there are still other issues).
Here are the SET() / GET() functions of the PMIC ACPI device,
which use this OpRegion, which clearly show the new behavior to
be correct:
OperationRegion (REGS, 0x8F, Zero, 0x50)
Field (REGS, ByteAcc, NoLock, Preserve)
{
CLNT, 8,
SA, 8,
OFF, 8,
VAL, 8,
RWM, 8
}
Method (GET, 3, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
RWM = Zero
If ((AVBG == One))
{
GPRW = Zero
}
}
Return (VAL) /* \_SB_.PCI0.I2C7.PMI5.VAL_ */
}
Method (SET, 4, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
VAL = Arg3
RWM = One
If ((AVBG == One))
{
GPRW = One
}
}
}
Fixes: 0afa877a5650 ("ACPI / PMIC: intel: add REGS operation region support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the initialization of two static variables to false which is
pointless.
Signed-off-by: wangzhitong <wangzhitong@uniontech.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
EC interrupts constantly wake up system from s2idle, so set
ec_no_wakeup by default to keep the system in s2idle and reduce
energy consumption.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a convenience function to tell whether a device is in D0 state,
primarily for use in drivers' probe or remove functions on busses where
the custom is to power on the device for the duration of both.
Returns false on non-ACPI systems.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Store a device's desired enumeration power state in struct
acpi_device_power during acpi_device object's initialisation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
