IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add the DesignWare EP device ID entry to pci_endpoint_test driver table.
Allow the device to be recognized and handled by the pci_endpoint_test
driver.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add device tree binding documentation for the EP in PCIe DesignWare driver.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The PCIe controller dual mode is capable of operating in Root Complex
(RC) mode as well as EP mode by configuration option.
Add EP support to the DesignWare driver on top of RC mode support.
Add new property on pci_epc structure which allow to configure
pci_epf_test driver accordingly to the controller specific requirements.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Replace "ctrlreg" reg-name by "dbi" to be coherent with similar drivers,
however it still be compatible with any previous DT that uses the old
reg-name.
Replace the PCIe base address example by a real PCIe base address in use.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Replace all initial lower case character into upper case in comments
and debug printks.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Replace all initial lower case character into upper case in comments
and debug printks.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The functions in linux/of_pci.h are primarily used by host bridge
drivers, so they can be private to drivers/pci/.
The remaining functions are still used mostly in host bridge drivers
that still live in arch specific code. Hopefully someday, those will get
moved into drivers/pci as well.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
There's no need for every config option to explicitly depend on
CONFIG_PCI, so move it out of individual option to the menu option.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Replace magic numbers by a self-explained define to ease human
comprehension.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Replace a division by 2 operation for a right shift rotation of 1 bit.
Probably any recent and decent compiler does this kind of substitution
in order to improve code performance. Nevertheless it's a coding good
practice whenever there is a division / multiplication by multiple of 2
to replace it by the equivalent operation in this case, the shift
rotation.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Replace of all initial lowercase character in comments and debug messages
to uppercase to maintain coherence.
Fix messages coherence within the DesignWare driver.
Fix code style on dw_pcie_irq_domain_free() function.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Add a callback to define the maximum number of vectors used by the RC.
Since this is a parameter associated to each SoC IP setting, makes sense
to be configurable and easily visible to future modifications.
Set DesignWare driver vectors number maximum to 256.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Remove space before tabs to fix the following checkpatch
warning:
WARNING: please, no space before tabs
+^Icase IMX6QP: ^I^I/* FALLTHROUGH */$
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "Link already up" message does not indicate any error, so
change it to dev_info() level instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Change Layerscape PCIe driver maintainers' email address
from freescale to nxp.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Roy Zang <roy.zang@nxp.com>
Now Rockchip PCIe drivers could support both of RC mode and EP
mode, so we need to rename the config name. This patch updates
defconfig to reflect the fact that we want to build Rockchip PCIe
controller as RC mode, into a module as before.
Cc: linux-arm-kernel@lists.infradead.org
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch documents the DT bindings for the Rockchip PCIe controller
when configured in EP mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add support for the Rockchip PCIe controller in endpoint mode;
it currently supports up to 32 regions with each region spanning
at least 1MB as per TRM.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Adds a "pci=noats" boot parameter. When supplied, all ATS related
functions fail immediately and the IOMMU is configured to not use
device-IOTLB.
Any function that checks for ATS capabilities directly against the devices
should also check this flag. Currently, such functions exist only in IOMMU
drivers, and they are covered by this patch.
The motivation behind this patch is the existence of malicious devices.
Lots of research has been done about how to use the IOMMU as protection
from such devices. When ATS is supported, any I/O device can access any
physical address by faking device-IOTLB entries. Adding the ability to
ignore these entries lets sysadmins enhance system security.
Signed-off-by: Gil Kupfer <gilkup@cs.technion.ac.il>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
When a PCIe AER error occurs, the TLP header information is printed in the
kernel message but it is missing from the tracepoint. A userspace program
can use this information in the tracepoint to better analyze problems.
To enable the tracepoint:
echo 1 > /sys/kernel/debug/tracing/events/ras/aer_event/enable
Example tracepoint output:
$ cat /sys/kernel/debug/tracing/trace
aer_event: 0000:01:00.0
PCIe Bus Error: severity=Uncorrected, non-fatal, Completer Abort
TLP Header={0x0,0x1,0x2,0x3}
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Make it more obvious that this documentation is referenced for
adding the Rockchip PCIe controller as RC mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Most of the initialization are used for both of RC driver and
EP driver; factor the initialization out to a new function,
rockchip_pcie_init_port(), in pcie-rockchip.c and rename the
original function to rockchip_pcie_host_init_port() to avoid
confusion. No functional changed intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Most of the DT properties are used for both of RC driver and EP driver,
so split them out in a new function, rockchip_pcie_parse_dt(), in
pcie-rockchip.c and rename the original function to
rockchip_pcie_parse_host_dt() to avoid confusion.
No functional changed intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
In preparation for introducing EP driver for Rockchip PCIe controller,
rename the RC driver from pcie-rockchip.c to pcie-rockchip-host.c, and
only leave some common functions in pcie-rockchip.c in order to be
reused for both of RC driver and EP driver.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
The non-functional change removes a custom function to parse and
allocate PCI resources in favour of pci_parse_request_of_pci_ranges().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
pci_epf_test_write() is never called in atomic context.
The call chain ending up at pci_epf_test_write() is:
[1] pci_epf_test_write() <- pci_epf_test_cmd_handler()
pci_epf_test_cmd_handler() is set as a parameter of INIT_DELAYED_WORK()
in pci_epf_test_probe().
This function is not called in atomic context.
Despite never getting called from atomic context, pci_epf_test_write()
calls mdelay() to busy wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
AER errors can be reported natively (Linux AER driver fields interrupts and
reads error state directly from hardware) or via the ACPI/APEI/GHES/CPER
path (platform firmware reads error state from hardware and sends it to
Linux via ACPI interfaces).
Previously the same error would produce different output depending on
whether it was reported natively or via ACPI. The CPER path resulted in
hard-to-understand messages, without a prefix. Instead use
__aer_print_error() for both native AER and CPER to provide a more
consistent log format.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Even if a device supports extended config space, i.e., it is a PCI-X Mode 2
or a PCI Express device, the extended space may not be accessible if
there's a conventional PCI bus in the path to it.
We currently figure that out in pci_cfg_space_size() by reading the first
dword of extended config space. On most platforms that returns ~0 data if
the space is inaccessible, but it may set error bits in PCI status
registers, and on some platforms it causes exceptions that we currently
don't recover from.
For example, a PCIe-to-conventional PCI bridge treats config transactions
with a non-zero Extended Register Address as an Unsupported Request on PCIe
and a received Master-Abort on the destination bus (see PCI Express to
PCI/PCI-X Bridge spec, r1.0, sec 4.1.3).
A sample case is a LS1043A CPU (NXP QorIQ Layerscape) platform with the
following bus topology:
LS1043 PCIe Root Port
-> PEX8112 PCIe-to-PCI bridge (doesn't support ext cfg on PCI side)
-> PMC slot connector (for legacy PMC modules)
With a PMC module topology as follows:
PMC connector
-> PCI-to-PCIe bridge
-> PCIe switch (4 ports)
-> 4 PCIe devices (one on each port)
The PCIe devices on the PMC module support extended config space, but we
can't reach it because the PEX8112 can't generate accesses to the extended
space on its secondary bus. Attempts to access it cause Unsupported
Request errors, which result in synchronous aborts on this platform.
To avoid these errors, check whether bridges are capable of generating
extended config space addresses on their secondary interfaces. If they
can't, we restrict devices below the bridge to only the 256-byte
PCI-compatible config space.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
[bhelgaas: changelog, rework patch so bus_flags testing is all in
pci_bridge_child_ext_cfg_accessible()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several PCIe hotplug controllers have errata that mean they do not set the
Command Completed bit unless writes to the Slot Command register change
"Control" bits. Command Completed is never set for writes that only change
software notification "Enable" bits. This results in timeouts like this:
pciehp 0000:00:1c.0:pcie004: Timeout on hotplug command 0x1038 (issued 65284 msec ago)
When this erratum is present, avoid these timeouts by marking commands
"completed" immediately unless they change the "Control" bits.
Here's the text of the Intel erratum CF118. We assume this applies to all
Intel parts:
CF118 PCIe Slot Status Register Command Completed bit not always
updated on any configuration write to the Slot Control
Register
Problem: For PCIe root ports (devices 0 - 10) supporting hot-plug,
the Slot Status Register (offset AAh) Command Completed
(bit[4]) status is updated under the following condition:
IOH will set Command Completed bit after delivering the new
commands written in the Slot Controller register (offset
A8h) to VPP. The IOH detects new commands written in Slot
Control register by checking the change of value for Power
Controller Control (bit[10]), Power Indicator Control
(bits[9:8]), Attention Indicator Control (bits[7:6]), or
Electromechanical Interlock Control (bit[11]) fields. Any
other configuration writes to the Slot Control register
without changing the values of these fields will not cause
Command Completed bit to be set.
The PCIe Base Specification Revision 2.0 or later describes
the “Slot Control Register” in section 7.8.10, as follows
(Reference section 7.8.10, Slot Control Register, Offset
18h). In hot-plug capable Downstream Ports, a write to the
Slot Control register must cause a hot-plug command to be
generated (see Section 6.7.3.2 for details on hot-plug
commands). A write to the Slot Control register in a
Downstream Port that is not hotplug capable must not cause a
hot-plug command to be executed.
The PCIe Spec intended that every write to the Slot Control
Register is a command and expected a command complete status
to abstract the VPP implementation specific nuances from the
OS software. IOH PCIe Slot Control Register implementation
is not fully conforming to the PCIe Specification in this
respect.
Implication: Software checking on the Command Completed status after
writing to the Slot Control register may time out.
Workaround: Software can read the Slot Control register and compare the
existing and new values to determine if it should check the
Command Completed status after writing to the Slot Control
register.
Per Sinan, the Qualcomm QDF2400 controller also does not set the Command
Completed bit unless writes to the Slot Command register change "Control"
bits.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Link: https://lkml.kernel.org/r/8770820b-85a0-172b-7230-3a44524e6c9f@molgen.mpg.de
Reported-by: Paul Menzel <pmenzel+linux-pci@molgen.mpg.de> # Lenovo X60
Tested-by: Paul Menzel <pmenzel+linux-pci@molgen.mpg.de> # Lenovo X60
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> # Qcom quirk
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
MT7622's hardware default value of vendor ID and class type is not correct,
fix that by setup the correct values before linkup with Endpoint.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Document the R-Car V3H (R8A77980) SoC in the R-Car PCIe bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
rcar_pcie_hw_init_{h1|gen2|gen3}() only differ in the PCIe PHY init code
and all end with a call to rcar_pcie_hw_init(), thus it makes sense to
move that call into the driver's probe() method and then rename those
functions to rcar_pcie_phy_init_{h1|gen2|gen3}().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car gen3 SoCs the PCIe PHY has its own register region, thus we
need to add the corresponding code in rcar_pcie_hw_init_gen3() and call
devm_phy_optional_get() at the driver's probing time, so that the
existing R-Car gen3 device trees (not having a PHY node) would still
work (we only need to power up the PHY on R-Car V3H).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Since rcar_pcie_hw_init() is polling PCIEPHYSR.PHYRDY there is no need
anymore for polling the PHY specific register in rcar_pcie_hw_init_h1().
Remove it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
In all the R-Car gen1/2/3 manuals, we are instructed to poll PCIEPHYSR
for PHYRDY=1 at an early stage of the PCIEC initialization -- while
the driver only does this on R-Car H1 (polling a PHY specific register).
Add the PHYRDY polling to rcar_pcie_hw_init(). Note that without the
special PHY driver on the R-Car V3H (R8A77980) the PCIEC initialization
just freezes the kernel -- adding the PHYRDY polling allows the init code
to exit gracefully on timeout (PHY starts powered down after reset on this
SoC).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
02bfeb484230 ("PCI/portdrv: Simplify PCIe feature permission checking")
removed the only call of pcie_port_acpi_setup() and removed portdrv_acpi.o
from the Makefile, but I forgot to remove pcie_port_acpi_setup() itself.
Remove pcie_port_acpi_setup() and the drivers/pci/pcie/portdrv_acpi.c file.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When Linux runs as a guest VM in Hyper-V and Hyper-V adds the virtual PCI
bus to the guest, Hyper-V always provides unique PCI domain.
commit 4a9b0933bdfc ("PCI: hv: Use device serial number as PCI domain")
overrode unique domain with the serial number of the first device added to
the virtual PCI bus.
The reason for that patch was to have a consistent and short name for the
device, but Hyper-V doesn't provide unique serial numbers. Using non-unique
serial numbers as domain IDs leads to duplicate device addresses, which
causes PCI bus registration to fail.
commit 0c195567a8f6 ("netvsc: transparent VF management") avoids the need
for commit 4a9b0933bdfc ("PCI: hv: Use device serial number as PCI
domain"). When scripts were used to configure VF devices, the name of
the VF needed to be consistent and short, but with commit 0c195567a8f6
("netvsc: transparent VF management") all the setup is done in the kernel,
and we do not need to maintain consistent name.
Revert commit 4a9b0933bdfc ("PCI: hv: Use device serial number as PCI
domain") so we can reliably support multiple devices being assigned to
a guest.
Tag the patch for stable kernels containing commit 0c195567a8f6
("netvsc: transparent VF management").
Fixes: 4a9b0933bdfc ("PCI: hv: Use device serial number as PCI domain")
Signed-off-by: Sridhar Pitchai <sridhar.pitchai@microsoft.com>
[lorenzo.pieralisi@arm.com: trimmed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Add COMPILE_TEST on driver config options with it. Some ARM drivers
still have arch dependencies, so we have to keep those dependent on ARM.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
[lorenzo.pieralisi@arm.com: rebased, updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch replaces the (1 << n) with BIT(n) and cleans up whitespace,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The controller clock can be switched off during suspend/resume,
let runtime PM take care of that.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-pci@vger.kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the early dump of PCI configuration space looks quite unhelpful,
e.g.
[ 0.000000] 60:
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000] 00
[ 0.000000]
which makes really hard to get anything out of this. Convert the function
to use print_hex_dump() to make output neat.
In the result we will have
[ 0.000000] 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
which is much, much better.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Intel 300 series chipset still has the same ACS issue as the previous
generations so extend the ACS quirk to cover it as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
The specification update indicates these have the same errata for
implementing non-standard ACS capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
IB/hfi1 contains custom macros for PCIe link configuration. Remove the
custom macros in favor of the PCIe link macros. No functional change
intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: use "GT" instead of "GB"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
The Link Control 2 register is missing macros for Target Link Speeds. Add
those in.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: use "GT" instead of "GB"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of implementing our own version of a SR-IOV configuration stub in
the nvme driver, use the existing pci_sriov_configure_simple() function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Instead of implementing our own version of a SR-IOV configuration stub in
the ena driver, use the existing pci_sriov_configure_simple() function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Some SR-IOV PF devices provide no functionality other than acting as a
means of enabling VFs. For these devices, we want to enable the VFs and
assign them to guest virtual machines, but there's no need to have a driver
for the PF itself.
Add a new pci-pf-stub driver to claim those PF devices and provide the
generic VF enable functionality. An administrator can use the sysfs
"sriov_numvfs" file to enable VFs, then assign them to guests.
For now I only have one example ID provided by Amazon in terms of devices
that require this functionality. The general idea is that in the future we
will see other devices added as vendors come up with devices where the PF
is more or less just a lightweight shim used to allocate VFs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
SR-IOV (Single Root I/O Virtualization) is an optional PCIe capability (see
PCIe r4.0, sec 9). A PCIe Function with the SR-IOV capability is referred
to as a PF (Physical Function). If SR-IOV is enabled on the PF, several
VFs (Virtual Functions) may be created. The VFs can be individually
assigned to virtual machines, which allows them to share a single hardware
device while being isolated from each other.
Some SR-IOV devices have resources such as queues and interrupts that must
be set up in the PF before enabling the VFs, so they require a PF driver to
do that.
Other SR-IOV devices don't require any PF setup before enabling VFs. Add a
pci_sriov_configure_simple() interface so PF drivers for such devices can
use it without repeating the VF-enabling code.
Tested-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>:wq
