IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Eliminate the following sparse warnings:
drivers/md/dm-stripe.c:443:12: warning: symbol 'dm_stripe_init' was not declared. Should it be static?
drivers/md/dm-stripe.c:456:6: warning: symbol 'dm_stripe_exit' was not declared. Should it be static?
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the collection of I/O statistics on user-defined regions of
a DM device. If no regions are defined no statistics are collected so
there isn't any performance impact. Only bio-based DM devices are
currently supported.
Each user-defined region specifies a starting sector, length and step.
Individual statistics will be collected for each step-sized area within
the range specified.
The I/O statistics counters for each step-sized area of a region are
in the same format as /sys/block/*/stat or /proc/diskstats but extra
counters (12 and 13) are provided: total time spent reading and
writing in milliseconds. All these counters may be accessed by sending
the @stats_print message to the appropriate DM device via dmsetup.
The creation of DM statistics will allocate memory via kmalloc or
fallback to using vmalloc space. At most, 1/4 of the overall system
memory may be allocated by DM statistics. The admin can see how much
memory is used by reading
/sys/module/dm_mod/parameters/stats_current_allocated_bytes
See Documentation/device-mapper/statistics.txt for more details.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If pool has 'no_free_space' set it means a previous allocation already
determined the pool has no free space (and failed that allocation with
-ENOSPC). By always returning -ENOSPC if 'no_free_space' is set, we do
not allow the pool to oscillate between allocating blocks and then not.
But a side-effect of this determinism is that if a user wants to be able
to allocate new blocks they'll need to reload the pool's table (to clear
the 'no_free_space' flag). This reload will happen automatically if the
pool's data volume is resized. But if the user takes action to free a
lot of space by deleting snapshot volumes, etc the pool will no longer
allow data allocations to continue without an intervening table reload.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Hold the mapped device's type_lock before calling populate_table() since
it is where the table's type is determined based on the specified
targets. There is no need to allow concurrent table loads to race to
establish the table's targets or type.
This eliminates the need to grab the lock in dm_table_set_type().
Also verify that the type_lock is held in both dm_set_md_type() and
dm_get_md_type().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A device-mapper device must always have a name consisting of a non-empty
string. If the device also has a uuid, this similarly must not be an
empty string.
The DM_DEV_CREATE ioctl enforces these rules when the device is created,
but this patch is needed to enforce them when DM_DEV_RENAME is used to
change the name or uuid.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
break_sharing() now handles an arbitrary alloc_data_block() error
the same way as provision_block(): marks pool read-only and errors the
cell.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Useful to know which pool is experiencing the error.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
It may be useful to switch a request-based table to the "error" target.
Enhance the DM core to allow a hybrid target_type which is capable of
handling either bios (via .map) or requests (via .map_rq).
Add a request-based map function (.map_rq) to the "error" target_type;
making it DM's first hybrid target. Train dm_table_set_type() to prefer
the mapped device's established type (request-based or bio-based). If
the mapped device doesn't have an established type default to making the
table with the hybrid target(s) bio-based.
Tested 'dmsetup wipe_table' to work on both bio-based and request-based
devices.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]) we also have a
new driver: esas2r which has a number of static checker problems, but which I
expect to resolve over the -rc course of 3.12 under the new driver exception.
We also have the error return updates that were discussed at LSF.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSJfX5AAoJEDeqqVYsXL0M8u8H+gN65iA4YeNc3Eq9F6mliLfg
JOIfn6GRz7ChbQ1ZZKdH/5xCOtzXphrkg7kRGmr9frsvYZ4X2c7W3xweQTA08gqP
wPH7/xyPffPnUm/r+V+SV41pm39bEjmltknLwiF572a6iOoVYQpnmDjdZQKT0jU0
QZEqI81+646m8edCnApLw3Tlsn2gBwHaDrkd55H2IQGTkOD016C0CQbM+cNMU440
qdqDcfRWCsp1fhLo3JH2kWTx8BihhyfEYAFz4tZwuFdGGkRZxF20HwyzV0h3hZOG
kZ2Gd1BFf0SybxOcESQmAukbcH5hyumX1Y7HMYKZbS2ubD4MCO1MO8UUtLXlxNc=
=PDBQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]).
We also have a new driver: esas2r which has a number of static checker
problems, but which I expect to resolve over the -rc course of 3.12
under the new driver exception.
We also have the error return that were discussed at LSF"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (118 commits)
[SCSI] sg: push file descriptor list locking down to per-device locking
[SCSI] sg: checking sdp->detached isn't protected when open
[SCSI] sg: no need sg_open_exclusive_lock
[SCSI] sg: use rwsem to solve race during exclusive open
[SCSI] scsi_debug: fix logical block provisioning support when unmap_alignment != 0
[SCSI] scsi_debug: fix endianness bug in sdebug_build_parts()
[SCSI] qla2xxx: Update the driver version to 8.06.00.08-k.
[SCSI] qla2xxx: print MAC via %pMR.
[SCSI] qla2xxx: Correction to message ids.
[SCSI] qla2xxx: Correctly print out/in mailbox registers.
[SCSI] qla2xxx: Add a new interface to update versions.
[SCSI] qla2xxx: Move queue depth ramp down message to i/o debug level.
[SCSI] qla2xxx: Select link initialization option bits from current operating mode.
[SCSI] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support.
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN
[SCSI] qla2xxx: Correct Interrupt Register offset for ISPFX00
[SCSI] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen().
[SCSI] qla2xxx: Send all AENs for ISPFx00 to above layers.
[SCSI] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS
...
If there are not enough stripes to handle, we'd better not always
queue all available work_structs. If one worker can only handle small
or even none stripes, it will impact request merge and create lock
contention.
With this patch, the number of work_struct running will depend on
pending stripes number. Note: some statistics info used in the patch
are accessed without locking protection. This should doesn't matter,
we just try best to avoid queue unnecessary work_struct.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some requests - particularly 'discard' and 'read' are handled
differently depending on whether a reshape is active or not.
It is harmless to assume reshape is active if it isn't but wrong
to act as though reshape is not active when it is.
So when we start reshape - after making clear to all requests that
reshape has started - use mddev_suspend/mddev_resume to flush out all
requests. This will ensure that no requests will be assuming the
absence of reshape once it really starts.
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() access various shape parameters (raid_disks, chunk_size
etc) which might be changed by raid5_start_reshape().
If the later is called at and awkward time during the form, the wrong
stripe_head might be used.
So introduce a 'seqcount' and after finding a stripe_head make sure
there is no reason to expect that we got the wrong one.
Signed-off-by: NeilBrown <neilb@suse.de>
Add a sysfs entry to control running workqueue thread number. If
group_thread_cnt is set to 0, we will disable workqueue offload handling of
stripes.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This is another attempt to create multiple threads to handle raid5 stripes.
This time I use workqueue.
raid5 handles request (especially write) in stripe unit. A stripe is page size
aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a
state machine for the corresponding stripe, which includes reading some disks
of the stripe, calculating parity, and writing some disks of the stripe. The
state machine is running in raid5d thread currently. Since there is only one
thread, it doesn't scale well for high speed storage. An obvious solution is
multi-threading.
To get better performance, we have some requirements:
a. locality. stripe corresponding to request submitted from one cpu is better
handled in thread in local cpu or local node. local cpu is preferred but some
times could be a bottleneck, for example, parity calculation is too heavy.
local node running has wide adaptability.
b. configurablity. Different setup of raid5 array might need diffent
configuration. Especially the thread number. More threads don't always mean
better performance because of lock contentions.
My original implementation is creating some kernel threads. There are
interfaces to control which cpu's stripe each thread should handle. And
userspace can set affinity of the threads. This provides biggest flexibility
and configurability. But it's hard to use and apparently a new thread pool
implementation is disfavor.
Recent workqueue improvement is quite promising. unbound workqueue will be
bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to
do affinity setting. For example, we can only include one HT sibling in
affinity. Since work is non-reentrant by default, and we can control running
thread number by limiting dispatched work_struct number.
In this patch, I created several stripe worker group. A group is a numa node.
stripes from cpus of one node will be added to a group list. Workqueue thread
of one node will only handle stripes of worker group of the node. In this way,
stripe handling has numa node locality. And as I said, we can control thread
number by limiting dispatched work_struct number.
The work_struct callback function handles several stripes in one run. A typical
work queue usage is to run one unit in each work_struct. In raid5 case, the
unit is a stripe. But we can't do that:
a. Though handling a stripe doesn't need lock because of reference accounting
and stripe isn't in any list, queuing a work_struct for each stripe will make
workqueue lock contended very heavily.
b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we
might dispatch request. If each work_struct only handles one stripe, such block
plug is meaningless.
This implementation can't do very fine grained configuration. But the numa
binding is most popular usage model, should be enough for most workloads.
Note: since we have only one stripe queue, switching to multi-thread might
decrease request size dispatching down to low level layer. The impact depends
on thread number, raid configuration and workload. So multi-thread raid5 might
not be proper for all setups.
Changes V1 -> V2:
1. remove WQ_NON_REENTRANT
2. disabling multi-threading by default
3. Add more descriptions in changelog
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
patch "make release_stripe lockless" changes the order stripes are released.
Originally I thought block layer can take care of request merge, but it appears
there are still some requests not merged. It's easy to fix the order.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
release_stripe still has big lock contention. We just add the stripe to a llist
without taking device_lock. We let the raid5d thread to do the real stripe
release, which must hold device_lock anyway. In this way, release_stripe
doesn't hold any locks.
The side effect is the released stripes order is changed. But sounds not a big
deal, stripes are never handled in order. And I thought block layer can already
do nice request merge, which means order isn't that important.
I kept the unplug release batch, which is unnecessary with this patch from lock
contention avoid point of view, and actually if we delete it, the stripe_head
release_list and lru can share storage. But the unplug release batch is also
helpful for request merge. We probably can delay wakeup raid5d till unplug, but
I'm still afraid of the case which raid5d is running.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When the last process closes /dev/mdX sync_blockdev will be called so
that all buffers get flushed.
So if it is then opened for the STOP_ARRAY ioctl to be sent there will
be nothing to flush.
However if we open /dev/mdX in order to send the STOP_ARRAY ioctl just
moments before some other process which was writing closes their file
descriptor, then there won't be a 'last close' and the buffers might
not get flushed.
So do_md_stop() calls sync_blockdev(). However at this point it is
holding ->reconfig_mutex. So if the array is currently 'clean' then
the writes from sync_blockdev() will not complete until the array
can be marked dirty and that won't happen until some other thread
can get ->reconfig_mutex. So we deadlock.
We need to move the sync_blockdev() call to before we take
->reconfig_mutex.
However then some other thread could open /dev/mdX and write to it
after we call sync_blockdev() and before we actually stop the array.
This can leave dirty data in the page cache which is awkward.
So introduce new flag MD_STILL_CLOSED. Set it before calling
sync_blockdev(), clear it if anyone does open the file, and abort the
STOP_ARRAY attempt if it gets set before we lock against further
opens.
It is still possible to get problems if you open /dev/mdX, write to
it, then issue the STOP_ARRAY ioctl. Just don't do that.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->flags is mostly used to record if an update of the
metadata is needed. Sometimes the whole field is tested
instead of just the important bits. This makes it difficult
to introduce more state bits.
So replace all bare tests of mddev->flags with tests for the bits
that actually need testing.
Signed-off-by: NeilBrown <neilb@suse.de>
Setting a variable to itself probably wasn't the intention here.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Whe we set the safe_mode_timeout to a smaller value we trigger a timeout
immediately - otherwise the small value might not be honoured.
However if the previous timeout was 0 meaning "no timeout", we didn't.
This would mean that no timeout happens until the next write completes,
which could be a long time.
Signed-off-by: NeilBrown <neilb@suse.de>
There is no really need as GFP_NOIO is very likely sufficient,
and failure is not catastrophic.
Calling md_allow_write here will convert a read-auto array to
read/write which could be confusing when you are just performing
a read operation.
Signed-off-by: NeilBrown <neilb@suse.de>
When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.
[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Prior to this patch these methods did a lookup followed by an insert.
Instead they now call a common mutate function that adjusts the value
according to a callback function. This avoids traversing the data
structures twice and hence improves performance.
Also factor out sm_ll_lookup_big_ref_count() for use by both
sm_ll_lookup() and sm_ll_mutate().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-btree now takes advantage of dm-bufio's ability to prefetch data via
dm_bm_prefetch(). Prior to this change many btree node visits were
causing a synchronous read.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove a visited leaf straight away from the stack, rather than
marking all it's children as visited and letting it get removed on the
next iteration. May also offer a micro optimisation in dm_btree_del.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reorder members in the cache structure to eliminate 6 out of 7 holes
(reclaiming 24 bytes). Also, the 'worker' and 'waker' members no longer
straddle cachelines.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Do not blindly override the queue limits (specifically io_min and
io_opt). Allow traditional stacking of these limits if io_opt is a
factor of the cache's data block size.
Without this patch mkfs.xfs does not recognize the cache device's
provided limits as a useful geometry (e.g. raid) so these hints are
ignored. This was due to setting io_min to a useless value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Do not blindly override the queue limits (specifically io_min and
io_opt). Allow traditional stacking of these limits if io_opt is a
factor of the thin-pool's data block size.
Without this patch mkfs.xfs does not recognize the thin device's
provided limits as a useful geometry (e.g. raid) so these hints are
ignored. This was due to setting io_min to a useless value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Place upper bound on the cache's data block size (1GB).
Inform users that the data block size can't be any arbitrary number,
i.e. its value must be between 32KB and 1GB. Also, it should be a
multiple of 32KB.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
dbf2576e37 ("workqueue: make all workqueues non-reentrant") made
WQ_NON_REENTRANT no-op and the flag is going away. Remove its usages.
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
On sparc32, which includes <linux/swap.h> from <asm/pgtable_32.h>:
drivers/md/dm-cache-policy-mq.c:962:13: error: conflicting types for 'remove_mapping'
include/linux/swap.h:285:12: note: previous declaration of 'remove_mapping' was here
As mq_remove_mapping() already exists, and the local remove_mapping() is
used only once, inline it manually to avoid the conflict.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Both marked for -stable, both since 3.3. I guess I should spend more
time testing...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=68H7
-----END PGP SIGNATURE-----
Merge tag 'md/3.11-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Two more bugfixes for md in 3.11
Both marked for -stable, both since 3.3. I guess I should spend more
time testing..."
* tag 'md/3.11-fixes' of git://neil.brown.name/md:
md/raid5: fix interaction of 'replace' and 'recovery'.
md/raid10: remove use-after-free bug.
If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.
This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).
So schedule those writes when s.replacing is set as well.
In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete. So introduce STRIPE_REPLACED to
record if the replacement has happened.
For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test. The latter
ensure that now IO has been flagged but not started. The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.
Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.
Finally if a NeedReplace device is not UPTODATE then that is an
error. We really must trigger a warning.
This bug was introduced in commit 9a3e1101b8
(md/raid5: detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.
Cc: stable@vger.kernel.org (3.3+)
Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua <qindehua@163.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We always need to be careful when calling generic_make_request, as it
can start a chain of events which might free something that we are
using.
Here is one place I wasn't careful enough. If the wbio2 is not in
use, then it might get freed at the first generic_make_request call.
So perform all necessary tests first.
This bug was introduced in 3.3-rc3 (24afd80d99) and can cause an
oops, so fix is suitable for any -stable since then.
Cc: stable@vger.kernel.org (3.3+)
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block IO driver bits from Jens Axboe:
"As I mentioned in the core block pull request, due to real life
circumstances the driver pull request would be late. Now it looks
like -rc2 late... On the plus side, apart form the rsxx update, these
are all things that I could argue could go in later in the cycle as
they are fixes and not features. So even though things are late, it's
not ALL bad.
The pull request contains:
- Updates to bcache, all bug fixes, from Kent.
- A pile of drbd bug fixes (no big features this time!).
- xen blk front/back fixes.
- rsxx driver updates, some of them deferred form 3.10. So should be
well cooked by now"
* 'for-3.11/drivers' of git://git.kernel.dk/linux-block: (63 commits)
bcache: Allocation kthread fixes
bcache: Fix GC_SECTORS_USED() calculation
bcache: Journal replay fix
bcache: Shutdown fix
bcache: Fix a sysfs splat on shutdown
bcache: Advertise that flushes are supported
bcache: check for allocation failures
bcache: Fix a dumb race
bcache: Use standard utility code
bcache: Update email address
bcache: Delete fuzz tester
bcache: Document shrinker reserve better
bcache: FUA fixes
drbd: Allow online change of al-stripes and al-stripe-size
drbd: Constants should be UPPERCASE
drbd: Ignore the exit code of a fence-peer handler if it returns too late
drbd: Fix rcu_read_lock balance on error path
drbd: fix error return code in drbd_init()
drbd: Do not sleep inside rcu
bcache: Refresh usage docs
...
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
allowed a bit more than just that. It also allows devices to be added
to a read-write array and to end up skipping recovery.
This patch removes the offending piece of code pending a rewrite for a
subsequent release.
More specifically:
If the array has a bitmap, then the device will still need a bitmap
based resync ('saved_raid_disk' is set under different conditions
is a bitmap is present).
If the array doesn't have a bitmap, then this is correct as long as
nothing has been written to the array since the metadata was checked
by ->validate_super. However there is no locking to ensure that there
was no write.
Bug was introduced in 3.10 and causes data corruption so
patch is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
1/ When an different between blocks is found, data is copied from
one bio to the other. However bv_len is used as the length to
copy and this could be zero. So use r10_bio->sectors to calculate
length instead.
Using bv_len was probably always a bit dubious, but the introduction
of bio_advance made it much more likely to be a problem.
2/ When preparing some blocks for sync, we don't set BIO_UPTODATE
except on bios that we schedule for a read. This ensures that
missing/failed devices don't confuse the loop at the top of
sync_request write.
Commit 8be185f2c9 "raid10: Use bio_reset()"
removed a loop which set BIO_UPTDATE on all appropriate bios.
So we need to re-add that flag.
These bugs were introduced in 3.10, so this patch is suitable for
3.10-stable, and can remove a potential for data corruption.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The alloc kthread should've been using try_to_freeze() - and also there
was the potential for the alloc kthread to get woken up after it had
shut down, which would have been bad.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Part of the job of garbage collection is to add up however many sectors
of live data it finds in each bucket, but that doesn't work very well if
it doesn't reset GC_SECTORS_USED() when it starts. Whoops.
This wouldn't have broken anything horribly, but allocation tries to
preferentially reclaim buckets that are mostly empty and that's not
gonna work with an incorrect GC_SECTORS_USED() value.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
The journal replay code starts by finding something that looks like a
valid journal entry, then it does a binary search over the unchecked
region of the journal for the journal entries with the highest sequence
numbers.
Trouble is, the logic was wrong - journal_read_bucket() returns true if
it found journal entries we need, but if the range of journal entries
we're looking for loops around the end of the journal - in that case
journal_read_bucket() could return true when it hadn't found the highest
sequence number we'd seen yet, and in that case the binary search did
the wrong thing. Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Stopping a cache set is supposed to make it stop attached backing
devices, but somewhere along the way that code got lost. Fixing this
mainly has the effect of fixing our reboot notifier.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
If we stopped a bcache device when we were already detaching (or
something like that), bcache_device_unlink() would try to remove a
symlink from sysfs that was already gone because the bcache dev kobject
had already been removed from sysfs.
So keep track of whether we've removed stuff from sysfs.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Whoops - bcache's flush/FUA was mostly correct, but flushes get filtered
out unless we say we support them...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
In the far-too-complicated closure code - closures can have destructors,
for probably dubious reasons; they get run after the closure is no
longer waiting on anything but before dropping the parent ref, intended
just for freeing whatever memory the closure is embedded in.
Trouble is, when remaining goes to 0 and we've got nothing more to run -
we also have to unlock the closure, setting remaining to -1. If there's
a destructor, that unlock isn't doing anything - nobody could be trying
to lock it if we're about to free it - but if the unlock _is needed...
that check for a destructor was racy. Argh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s5m4
-----END PGP SIGNATURE-----
Merge tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Add a device-mapper target called dm-switch to provide a multipath
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes"
* tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: add switch target
dm: update maintainers
dm: optimize reorder structure
dm: optimize use SRCU and RCU
dm bufio: submit writes outside lock
dm cache: fix arm link errors with inline
dm verity: use __ffs and __fls
dm flakey: correct ctr alloc failure mesg
dm verity: remove pointless comparison
dm: use __GFP_HIGHMEM in __vmalloc
dm verity: fix inability to use a few specific devices sizes
dm ioctl: set noio flag to avoid __vmalloc deadlock
dm mpath: fix ioctl deadlock when no paths
dm-switch is a new target that maps IO to underlying block devices
efficiently when there is a large number of fixed-sized address regions
but there is no simple pattern to allow for a compact mapping
representation such as dm-stripe.
Though we have developed this target for a specific storage device, Dell
EqualLogic, we have made an effort to keep it as general purpose as
possible in the hope that others may benefit.
Originally developed by Jim Ramsay. Simplified by Mikulas Patocka.
Signed-off-by: Jim Ramsay <jim_ramsay@dell.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This reorder actually improves performance by 20% (from 39.1s to 32.8s)
on x86-64 quad core Opteron.
I have no explanation for this, possibly it makes some other entries are
better cache-aligned.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes "io_lock" and "map_lock" in struct mapped_device and
"holders" in struct dm_table and replaces these mechanisms with
sleepable-rcu.
Previously, the code would call "dm_get_live_table" and "dm_table_put" to
get and release table. Now, the code is changed to call "dm_get_live_table"
and "dm_put_live_table". dm_get_live_table locks sleepable-rcu and
dm_put_live_table unlocks it.
dm_get_live_table_fast/dm_put_live_table_fast can be used instead of
dm_get_live_table/dm_put_live_table. These *_fast functions use
non-sleepable RCU, so the caller must not block between them.
If the code changes active or inactive dm table, it must call
dm_sync_table before destroying the old table.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes dm-bufio so that it submits write I/Os outside of the
lock. If the number of submitted buffers is greater than the number of
requests on the target queue, submit_bio blocks. We want to block outside
of the lock to improve latency of other threads that may need the lock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use __always_inline to avoid a link failure with gcc 4.6 on ARM.
gcc 4.7 is OK.
It creates a function block_div.part.8, it references __udivdi3 and
__umoddi3 and it is never called. The references to __udivdi3 and
__umoddi3 cause a link failure.
Reported-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes ffs() to __ffs() and fls() to __fls() which don't add
one to the result.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the reference to the "linear" target from the error message
issued when allocation fails in the flakey target.
Cc: Robin Dong <sanbai@taobao.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove num < 0 test in verity_ctr because num is unsigned.
(Found by Coverity.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use __GFP_HIGHMEM in __vmalloc.
Pages allocated with __vmalloc can be allocated in high memory that is not
directly mapped to kernel space, so use __GFP_HIGHMEM just like vmalloc
does. This patch reduces memory pressure slightly because pages can be
allocated in the high zone.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a boundary condition that caused failure for certain device sizes.
The problem is reported at
http://code.google.com/p/cryptsetup/issues/detail?id=160
For certain device sizes the number of hashes at a specific level was
calculated incorrectly.
It happens for example for a device with data and metadata block size 4096
that has 16385 blocks and algorithm sha256.
The user can test if he is affected by this bug by running the
"veritysetup verify" command and also by activating the dm-verity kernel
driver and reading the whole block device. If it passes without an error,
then the user is not affected.
The condition for the bug is:
Split the total number of data blocks (data_block_bits) into bit strings,
each string has hash_per_block_bits bits. hash_per_block_bits is
rounddown(log2(metadata_block_size/hash_digest_size)). Equivalently, you
can say that you convert data_blocks_bits to 2^hash_per_block_bits base.
If there some zero bit string below the most significant bit string and at
least one bit below this zero bit string is set, then the bug happens.
The same bug exists in the userspace veritysetup tool, so you must use
fixed veritysetup too if you want to use devices that are affected by
this boundary condition.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.4+
Cc: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set noio flag while calling __vmalloc() because it doesn't fully respect
gfp flags to avoid a possible deadlock (see commit
502624bdad).
This should be backported to stable kernels 3.8 and newer. The kernel 3.8
doesn't have memalloc_noio_save(), so we should set and restore process
flag PF_MEMALLOC instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When multipath needs to retry an ioctl the reference to the
current live table needs to be dropped. Otherwise a deadlock
occurs when all paths are down:
- dm_blk_ioctl takes a reference to the current table
and spins in multipath_ioctl().
- A new table is being loaded, but upon resume the process
hangs in dm_table_destroy() waiting for references to
drop to zero.
With this patch the reference to the old table is dropped
prior to retry, thereby avoiding the deadlock.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
The recent comment:
commit 7e83ccbecd
md/raid10: Allow skipping recovery when clean arrays are assembled
Causes raid10 to skip a recovery in certain cases where it is safe to
do so. Unfortunately it also causes a reshape to be skipped which is
never safe. The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).
Bug was introduced in 3.10, so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
There is a bug in 'check_reshape' for raid5.c To checks
that the new minimum number of devices is large enough (which is
good), but it does so also after the reshape has started (bad).
This is bad because
- the calculation is now wrong as mddev->raid_disks has changed
already, and
- it is pointless because it is now too late to stop.
So only perform that test when reshape has not been committed to.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ If a RAID10 is being reshaped to a fewer number of devices
and is stopped while this is ongoing, then when the array is
reassembled the 'mirrors' array will be allocated too small.
This will lead to an access error or memory corruption.
2/ A sanity test for a reshaping RAID10 array is restarted
is slightly incorrect.
Due to the first bug, this is suitable for any -stable
kernel since 3.5 where this code was introduced.
Cc: stable@vger.kernel.org (v3.5+)
Signed-off-by: NeilBrown <neilb@suse.de>
Some of bcache's utility code has made it into the rest of the kernel,
so drop the bcache versions.
Bcache used to have a workaround for allocating from a bio set under
generic_make_request() (if you allocated more than once, the bios you
already allocated would get stuck on current->bio_list when you
submitted, and you'd risk deadlock) - bcache would mask out __GFP_WAIT
when allocating bios under generic_make_request() so that allocation
could fail and it could retry from workqueue. But bio_alloc_bioset() has
a workaround now, so we can drop this hack and the associated error
handling.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Journal writes need to be marked FUA, not just REQ_FLUSH. And btree node
writes have... weird ordering requirements.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Now that we're tracking dirty data per stripe, we can add two
optimizations for raid5/6:
* If a stripe is already dirty, force writes to that stripe to
writeback mode - to help build up full stripes of dirty data
* When flushing dirty data, preferentially write out full stripes first
if there are any.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
To make background writeback aware of raid5/6 stripes, we first need to
track the amount of dirty data within each stripe - we do this by
breaking up the existing sectors_dirty into per stripe atomic_ts
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Previously, dirty_data wouldn't get initialized until the first garbage
collection... which was a bit of a problem for background writeback (as
the PD controller keys off of it) and also confusing for users.
This is also prep work for making background writeback aware of raid5/6
stripes.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
The old lazy sorting code was kind of hacky - rewrite in a way that
mathematically makes more sense; the idea is that the size of the sets
of keys in a btree node should increase by a more or less fixed ratio
from smallest to biggest.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Old gcc doesnt like the struct hack, and it is kind of ugly. So finish
off the work to convert pr_debug() statements to tracepoints, and delete
pkey()/pbtree().
Signed-off-by: Kent Overstreet <koverstreet@google.com>
The tracepoints were reworked to be more sensible, and fixed a null
pointer deref in one of the tracepoints.
Converted some of the pr_debug()s to tracepoints - this is partly a
performance optimization; it used to be that with DEBUG or
CONFIG_DYNAMIC_DEBUG pr_debug() was an empty macro; but at some point it
was changed to an empty inline function.
Some of the pr_debug() statements had rather expensive function calls as
part of the arguments, so this code was getting run unnecessarily even
on non debug kernels - in some fast paths, too.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
The most significant change is that btree reads are now done
synchronously, instead of asynchronously and doing the post read stuff
from a workqueue.
This was originally done because we can't block on IO under
generic_make_request(). But - we already have a mechanism to punt cache
lookups to workqueue if needed, so if we just use that we don't have to
deal with the complexity of doing things asynchronously.
The main benefit is this makes the locking situation saner; we can hold
our write lock on the btree node until we're finished reading it, and we
don't need that btree_node_read_done() flag anymore.
Also, for writes, btree_write() was broken out into btree_node_write()
and btree_leaf_dirty() - the old code with the boolean argument was dumb
and confusing.
The prio_blocked mechanism was improved a bit too, now the only counter
is in struct btree_write, we don't mess with transfering a count from
struct btree anymore.
This required changing garbage collection to block prios at the start
and unblock when it finishes, which is cleaner than what it was doing
anyways (the old code had mostly the same effect, but was doing it in a
convoluted way)
And the btree iter btree_node_read_done() uses was converted to a real
mempool.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
An old version of gcc was complaining about using a const int as the
size of a stack allocated array. Which should be fine - but using
ARRAY_SIZE() is better, anyways.
Also, refactor the code to use scnprintf().
Signed-off-by: Kent Overstreet <koverstreet@google.com>
bio_alloc_bioset returns NULL on failure. This fix adds a missing check
for potential NULL pointer dereferencing.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
MD: Remember the last sync operation that was performed
This patch adds a field to the mddev structure to track the last
sync operation that was performed. This is especially useful when
it comes to what is recorded in mismatch_cnt in sysfs. If the
last operation was "data-check", then it reports the number of
descrepancies found by the user-initiated check. If it was a
"repair" operation, then it is reporting the number of
descrepancies repaired. etc.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
RAID5 uses a 'per-array' value for the 'size' of each device.
RAID0 uses a 'per-device' value - it can be different for each device.
When converting a RAID5 to a RAID0 we must ensure that the per-device
size of each device matches the per-array size for the RAID5, else
the array will change size.
If the metadata cannot record a changed per-device size (as is the
case with v0.90 metadata) the array could get bigger on restart. This
does not cause data corruption, so it not a big issue and is mainly
yet another a reason to not use 0.90.
Signed-off-by: NeilBrown <neilb@suse.de>
It isn't really enough to check that the rdev is present, we need to
also be sure that the device is still In_sync.
Doing this requires using rcu_dereference to access the rdev, and
holding the rcu_read_lock() to ensure the rdev doesn't disappear while
we look at it.
Signed-off-by: NeilBrown <neilb@suse.de>
As 'enough' accesses conf->prev and conf->geo, which can change
spontanously, it should guard against changes.
This can be done with device_lock as start_reshape holds device_lock
while updating 'geo' and end_reshape holds it while updating 'prev'.
So 'error' needs to hold 'device_lock'.
On the other hand, raid10_end_read_request knows which of the two it
really wants to access, and as it is an active request on that one,
the value cannot change underneath it.
So change _enough to take flag rather than a pointer, pass the
appropriate flag from raid10_end_read_request(), and remove the locking.
All other calls to 'enough' are made with reconfig_mutex held, so
neither 'prev' nor 'geo' can change.
Signed-off-by: NeilBrown <neilb@suse.de>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When a device has failed, it needs to be removed from the personality
module before it can be removed from the array as a whole.
The first step is performed by md_check_recovery() which is called
from the raid management thread.
So when a HOT_REMOVE ioctl arrives, wait briefly for md_check_recovery
to have run. This increases the chance that the ioctl will succeed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Neil Brown <nfbrown@suse.de>
This doesn't really need to be initialised, but it doesn't hurt,
silences the compiler, and as it is a counter it makes sense for it to
start at zero.
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Fix raid_resume not reviving failed devices in all cases
When a device fails in a RAID array, it is marked as Faulty. Later,
md_check_recovery is called which (through the call chain) calls
'hot_remove_disk' in order to have the personalities remove the device
from use in the array.
Sometimes, it is possible for the array to be suspended before the
personalities get their chance to perform 'hot_remove_disk'. This is
normally not an issue. If the array is deactivated, then the failed
device will be noticed when the array is reinstantiated. If the
array is resumed and the disk is still missing, md_check_recovery will
be called upon resume and 'hot_remove_disk' will be called at that
time. However, (for dm-raid) if the device has been restored,
a resume on the array would cause it to attempt to revive the device
by calling 'hot_add_disk'. If 'hot_remove_disk' had not been called,
a situation is then created where the device is thought to concurrently
be the replacement and the device to be replaced. Thus, the device
is first sync'ed with the rest of the array (because it is the replacement
device) and then marked Faulty and removed from the array (because
it is also the device being replaced).
The solution is to check and see if the device had properly been removed
before the array was suspended. This is done by seeing whether the
device's 'raid_disk' field is -1 - a condition that implies that
'md_check_recovery -> remove_and_add_spares (where raid_disk is set to -1)
-> hot_remove_disk' has been called. If 'raid_disk' is not -1, then
'hot_remove_disk' must be called to complete the removal of the previously
faulty device before it can be revived via 'hot_add_disk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Break-up untidy function
Clean-up excessive indentation by moving some code in raid_resume()
into its own function.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f (raid10) and 6b740b8d79 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
__md_stop_writes() will currently sometimes freeze recovery.
So any caller must be ready for that to happen, and indeed they are.
However if __md_stop_writes() doesn't freeze_recovery, then
a recovery could start before mddev_suspend() is called, which
could be awkward. This can particularly cause problems or dm-raid.
So change __md_stop_writes() to always freeze recovery. This is safe
and more predicatable.
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Tested-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
The patch that converted raid5 to use bio_reset() forgot to initialize
bi_vcnt.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: NeilBrown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Tested-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix detection of the need to resize the dm thin metadata device.
The code incorrectly tried to extend the metadata device when it
didn't need to due to a merging error with patch 24347e9 ("dm thin:
detect metadata device resizing").
device-mapper: transaction manager: couldn't open metadata space map
device-mapper: thin metadata: tm_open_with_sm failed
device-mapper: thin: aborting transaction failed
device-mapper: thin: switching pool to failure mode
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
