IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called with a NULL port
driver-data pointer or if some other always-true sanity checks failed.
The bogus sanity checks were later removed by commit ce039bd4b21f ("USB:
serial: mos7840: drop paranoid port checks") and 7b2faede671a ("USB:
serial: mos7840: drop port driver data accessors") but the
function-header comments were never updated to match.
Drop the outdated return-value comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were ever called with a NULL port
driver-data pointer. The return value was later changed to zero by
commit 23198fda7182 ("tty: fix chars_in_buffers") but the bogus sanity
checks were left in place as were the outdated function-header comments.
The port driver data isn't cleared until after the port has been
deregistered and all open ttys have been hung up so drop the unnecessary
sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called while or after the port
had been closed. The return value was later changed to zero by commit
d76f2f4462bb ("io_edgeport: Fix various bogus returns to the tty
layer") but the bogus sanity checks were left in place as were the
outdated function-header comments.
These callbacks will never be called for an uninitialised port so drop
the unnecessary sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Both the dp_write_urb_in_use flag and dp_out_buf_len counter should be
accessed while holding the driver port lock. Add the missing locking to
chars_in_buffer and clean up the implementation somewhat by using a
common exit path.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Due to an ancient quirk in n_tty poll implementation, the
digi_acceleport driver has been reporting that its queue contains 256
(WAKEUP_CHARS) characters whenever its write URB is in use.
This has not been necessary since 2003 when the line-discipline started
taking the write room into account so let's return the maximum transfer
size again in order to over-report a little less and incidentally fix
the related debug statement.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_operations::chars_in_buffer is being switched to return uint. Do the
same for usb_serial_driver's chars_in_buffer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). Both of them are being
updated to return an unsigned int. Switch also
usb_serial_driver::write_room and all its users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message, drop unrelated comment change ]
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the device id for the ADLINK ND-6530 which is a PL2303GC based
device.
Signed-off-by: Zolton Jheng <s6668c2t@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for the Startech.com generic serial to USB converter.
It seems to be a bone stock TI_3410. I have been using this patch for
years.
Signed-off-by: Sean MacLennan <seanm@seanm.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the IDS GmbH Vendor ID and the Product IDs for SI31A (2xRS232)
and CM31A (LoRaWAN Modem).
Signed-off-by: Dominik Andreas Schorpp <dominik.a.schorpp@ids.de>
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big set of USB and Thunderbolt driver updates for 5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work
with (something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa42A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMEACgkQBzLb5W/IocS+oq7+D7P3V581sAn1Dcy2Qq
Yz370/X2hrjXAyIm7/Cz
=5dj/
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work with
(something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (371 commits)
usb: Fix up movement of USB core kerneldoc location
usb: dwc3: gadget: Handle DEV_TXF_FLUSH_BYPASS capability
usb: dwc3: Capture new capability register GHWPARAMS9
usb: gadget: prevent a ternary sign expansion bug
usb: dwc3: core: Do core softreset when switch mode
usb: dwc2: Get rid of useless error checks in suspend interrupt
usb: dwc2: Update dwc2_handle_usb_suspend_intr function.
usb: dwc2: Add exit hibernation mode before removing drive
usb: dwc2: Add hibernation exiting flow by system resume
usb: dwc2: Add hibernation entering flow by system suspend
usb: dwc2: Allow exit hibernation in urb enqueue
usb: dwc2: Move exit hibernation to dwc2_port_resume() function
usb: dwc2: Move enter hibernation to dwc2_port_suspend() function
usb: dwc2: Clear GINTSTS_RESTOREDONE bit after restore is generated.
usb: dwc2: Clear fifo_map when resetting core.
usb: dwc2: Allow exiting hibernation from gpwrdn rst detect
usb: dwc2: Fix hibernation between host and device modes.
usb: dwc2: Fix host mode hibernation exit with remote wakeup flow.
usb: dwc2: Reset DEVADDR after exiting gadget hibernation.
usb: dwc2: Update exit hibernation when port reset is asserted
...
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The three-character drain delay was added by commit f1175daa5312 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f81036d ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a debug printk to dump the GPIO configuration stored in EEPROM
during probe.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new GPIO valid-mask feature to inform gpiolib which pins are
available for use instead of handling that in a request callback.
This also allows user space to figure out which pins are available
through the chardev interface without having to request each pin in
turn.
Note that the return value when requesting an unavailable pin will now
be -EINVAL instead of -ENODEV.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port struct device rather than tty class device for debugging.
Note that while USB serial doesn't support serdev yet (due to serdev not
handling hotplugging), serdev ttys do not have a corresponding class
device and would have been logged using a "(NULL device *):" prefix.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unused definitions relating to a never mainlined custom
proc-interface and some likewise unused string descriptor definitions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ti_usb_3410_5052 has supported changing the closing_wait parameter
through TIOCSSERIAL (setserial) for about a decade and commit
f1175daa5312 ("USB: ti_usb_3410_5052: kill custom closing_wait").
It's time to drop the corresponding driver-specific module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that all USB serial drivers supports setting the closing_wait
parameter through TIOCSSERIAL (setserial) it's time to drop the
corresponding io_ti module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL implementation needs to compare the old flag and divisor
settings with the new to detect ASYNC_SPD changes, but there's no need
to copy all driver state to the stack for that.
While at it, unbreak the function parameter list.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the deprecated custom_divisor field is an unprivileged
operation so after verifying that flag field does not contain any
privileged changes both updates can be carried out by any user.
Combine the two branches and drop the erroneous comment.
Note that private flags field is only used for ASYNC flags so there's no
need to try to retain any other bits when updating the flags.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL error handling is inconsistent at best, but drivers tend
to ignore requests to change parameters which cannot be changed rather
than return an error.
The FTDI driver ignores change requests for all immutable parameters but
baud_base so return success also in this case for consistency.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
