IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a generic power domain implementation, TI SCI PM Domains, that
will hook into the genpd framework and allow the TI SCI protocol to
control device power states.
Also, provide macros representing each device index as understood
by TI SCI to be used in the device node power-domain references.
These are identifiers for the K2G devices managed by the PMMC.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
SoCs after A31 has a clock controller module in the PRCM part.
Support the clock controller module on H3/5 and A64 now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
iqc1, iqc2, tegra_clk_pll_a_out_adsp, tegra_clk_pll_a_out0_out_adsp, adsp
and adsp neon were not modelled. dp2 wasn't modelled for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unlike other R-Car Gen2 SoCs with Cortex-A15 CPU cores, R-Car V2H does
not have a programmable Z clock (Cortex-A15 CPU core clock), but uses a
fixed divider.
This is similar to the Z2 clock (Cortex-A7 CPU core clock) on R-Car E2.
Hence:
- Remove the Z clock output from the cpg_clocks node, as this implied
a programmable clock,
- Add the Z clock as a fixed factor clock,
- Let the first CPU node point to the new Z clock,
- Remove the Z clock index from the bindings (this definition was used
by r8a7792.dtsi only, and was not a contract between DT and driver).
Fixes: 7c4163aae3d8e5b9 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing module clock for the second channel of the display unit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch lists STM32F7's RCC numeric constants.
It will be used by clock and reset drivers, and DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[include rename in rk1108.dtsi to prevent compile errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cA1
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- make reset drivers with bool Kconfig options explicitly non-modular
- fix uniphier non-static symbol warnings
- fix socfpga nr_resets property
- new drivers for the Arria10 and i.MX7 system reset controllers
- fix sunxi 64-bit compilation
-----BEGIN PGP SIGNATURE-----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=5xmN
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.12-1' of git://git.pengutronix.de/git/pza/linux into next/drivers
Reset controller changes for v4.12
- make reset drivers with bool Kconfig options explicitly non-modular
- fix uniphier non-static symbol warnings
- fix socfpga nr_resets property
- new drivers for the Arria10 and i.MX7 system reset controllers
- fix sunxi 64-bit compilation
* tag 'reset-for-4.12-1' of git://git.pengutronix.de/git/pza/linux:
reset: sunxi: fix for 64-bit compilation
reset: Add Altera Arria10 SR Reset Controller
dt-bindings: reset: a10sr: Add Arria10 SR Reset Controller offsets
reset: Add i.MX7 SRC reset driver
reset-socfpga: Fix nr_resets property
reset: uniphier: fix non static symbol warnings
reset: pistachio: make it explicitly non-modular
reset: ath79: make it explicitly non-modular
reset: oxnas: make it explicitly non-modular
reset: meson: make it explicitly non-modular
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra210 has 2 special resets which don't follow the normal pattern:
DVCO and ADSP. Add them in this patch.
Changelog:
v2: add DT bindings file
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock clocks the ADSP Cortex-A9.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has 3 DMIC inputs which can be clocked from the recovered clock
of several other audio inputs (eg. i2s0, i2s1, ...). To model this, we
add a 3 new clocks similar to the audio* clocks which handle the same
function for the I2S and SPDIF clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is used to clock the HDMI CEC interface.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 2 ISP clocks (ispa and ispb) share a mux/divider control. So model
this as 1 mux/divider clock and child gate clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Arria10 System Resource Chip reset controller handles the
Arria10 peripheral PHYs. This patch adds the offsets for
these PHYs.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The timer-ids are wrong compared to the manual, probably due a simple
copy-paste mistake from the otherwise very similar rk3288. And there
are even more timers in the system than the ones wrongly listed here.
Timer-Ids were unused both in clock-driver as well as devicetree
till now, so fixing them won't break anything.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock and the C4 power domain,
so it can be power managed using that clock in the future.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SDHI controller in the RZ/A1 has 2 clock sources per channel and both
need to be enabled/disabled for proper operation. This fixes the fact that
the define for R7S72100_CLK_SDHI1 was not correct to begin with (typo), and
that all 4 clock sources need to be defined an used.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=o8o/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc
register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=od7u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
We sometimes collect non-critical fixes that come in during the later part
of the merge window in a branch for the next release instead, and this is
that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for SCPI
to only enable on ARM{,64}.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NhZq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
- new driver for stts751
- it87: Added support for IT8622E and IT8792E; improved support for other chips
- lm70: Added support for TMP122/124
- use permission-specific DEVICE_ATTR variants where possible
- fixed overflows in various drivers
- minor improvements in various drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QLmt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for stts751
- it87: Added support for IT8622E and IT8792E; improved support for
other chips
- lm70: Added support for TMP122/124
- use permission-specific DEVICE_ATTR variants where possible
- fixed overflows in various drivers
- minor improvements in various drivers
* tag 'hwmon-for-linus-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (95 commits)
hwmon: (sht15) Add device tree support
devicetree: add lm90 thermal_zone sensor support
hwmon: (it87) Add support for IT8792E
hwmon: (it87) Do not overwrite bit 2..6 of pwm control registers
hwmon: (it87) Fix pwm4 detection for IT8620 and IT8628
hwmon: (it87) Ensure that pwm control cache is current before updating values
hwmon: (it87) Improve IT8622 support
hwmon: (it87) Add support for IT8622E
hwmon: (it87) Add feature flag indicating that VIN3 is connected to 5V
DT: add binding documentation for STTS751
hwmon: new driver for ST stts751 thermal sensor
hwmon: Register thermal zone only if 'dev' parameter was provided
hwmon: Relax name attribute validation for new APIs
hwmon: Update documentation to clarify rules for the 'name' attribute
hwmon: Make name attribute mandatory for new APIs
hwmon: (lm70) Add support for TI TMP122/124
hwmon: (lm70) Utilize dev_warn instead of pr_warn
hwmon: (ltc4151) Export OF device ID table as module aliases
hwmon: (adc128d818) Preserve operation mode
hwmon: (adc128d818) Support operation modes 1-3
...
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYk3YaAAoJEME3ZuaGi4PXYwAP/2d7SiLymurXwmctrxm9Q5kI
ZD7xdTr5JWq/sbuGfDHLKUz4iPMBsdQqRwczZ+DSls+Iet1fNw4enmoU/p1SpZ/5
31EFB3uN28DSL4ZA3SzOrzPgcdMRxXOYhUMq9DTY5N8h0LlI2TwB3WBDgWTpGB6R
NXX3wKulH2hXJyOizOZh2yel5KvzLqug7j/V0u9K1OmUISmTy3XfDWaXIVk33MUw
IZ6qpgTzShw6sZj5VmR9CFPFbDjwExTVenIA9gwewJlQNQnqrsg0BdEF3ZvasW+V
eFeLV4ieZHKzEoVjwdxGgTLLwjjL/orsWQ5CYiQNeCKC85rgTVfijTe8s+QKOYAq
SiV1GghHACExpCULhtQiqioFsUAUPJ+iq/EZ9NfNh7QzE5Y05RJ7bRgRd2UdBlN8
BXhekgN5RepLwKWHK8oYivMMpIKzDve1ICRpQYBVxmmwg9nzRz6Nij2YUi4oEb5j
77FOuyKe5M+QCIoKVn2v/CDQMemGkI8OEsKubjDKcOZ2V2COw7Sr1L/GCGVCslLM
FyOjaTKeoIzkrx62qgqGFuNwEaZwW0dDacHrZrccEAn9P9G7O/cU8EE9F5nJqGG0
IeDaPH7BqQ0gOHbvrEkljSbJuuOMQmZJl6qh8MMJYB9P8u9Ft3OXUXJ1qBNZB4si
E5nFWGj0CMm0UfBWgkD/
=02Sx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Pull "Samsung DeviceTree ARM64 update for v4.11, third round" from Krzysztof Kozłowski:
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
* tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
clk: samsung: exynos5433: Add data for 250MHz and 278MHz PLL rates
clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
...
This patch updates the LM90's devicetree definition to
include the #thermal-sensor-cells property as well as
the sensor constants in include/dt-bindings/thermal/lm90.h.
Cc: Wei Ni <wni@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
