IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add support to setup_mdio_bus for internal phy declaration. Introduce a
flag to use the legacy port phy mapping by default and use the direct
mapping if a mdio node is detected in the switch node. Register a
dedicated mdio internal mdio bus to address the different mapping
between port and phy if the mdio node is detected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The witch require some extra delay after setting page or the next
read/write can use still use the old page. Add a delay after the
set_page function to address this as it's done in QSDK legacy driver.
Some timeouts were notice with VLAN and phy function, enlarge the
mdio busy wait timeout to fix these problems.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy qsdk code used a different delay instead of the max value.
Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable
using the standard rx/tx-internal-delay-ps ethernet binding and apply
qsdk values by default. The connected gmac doesn't add any delay so no
additional delay is added to tx/rx.
On this switch the delay is actually in ns so value should be in the
1000 order. Any value converted from ps to ns by dividing it by 1000
as the switch max value for delay is 3ns.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k internal phy driver require some special debug value to be set
based on the switch revision. Rework the switch id read function to
also read the chip revision.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch qca8327 needs special settings for the GLOBAL_FC_THRES regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port 5 of the qca8337 have some problem in flood condition. The
original legacy driver had some specific buffer and priority settings
for the different port suggested by the QCA switch team. Add this
missing settings to improve switch stability under load condition.
The packet priority tweak is only needed for the qca8337 switch and
other qca8k switch are not affected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8327 switch is a low tier version of the more recent qca8337.
It does share the same regs used by the qca8k driver and can be
supported with minimal change.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iopoll macro instead of while loop.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full 802.1q VLAN support to the qca8k, allowing the use of
vlan_filtering and more complicated bridging setups than allowed by
basic port VLAN support.
Tested with a number of untagged ports with separate VLANs and then a
trunk port with all the VLANs tagged on it.
v3:
- Pull QCA8K_PORT_VID_DEF changes into separate cleanup patch
- Reverse Christmas tree notation for variable definitions
- Use untagged instead of tagged for consistency
v2:
- Return sensible errnos on failure rather than -1 (rmk)
- Style cleanups based on Florian's feedback
- Silently allow VLAN 0 as device correctly treats this as no tag
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a magic value of 1 when configuring the port VIDs add
a QCA8K_PORT_VID_DEF define and use that instead. Also fix up the
bitmask in the process; the top 4 bits are reserved so this wasn't a
problem, but only masking 12 bits is the correct approach.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch has a single max frame size configuration register, so we
track the requested MTU for each port and apply the largest.
v2:
- Address review feedback from Vladimir Oltean
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the handling of the SGMII interface on the QCA8K
devices. Previously the driver did no configuration of the port, even if
it was selected. We now configure it up in the appropriate
PHY/MAC/Base-X mode depending on what phylink tells us we are connected
to and ensure it is enabled.
Tested with a device where the CPU connection is RGMII (i.e. the common
current use case) + one where the CPU connection is SGMII. I don't have
any devices where the SGMII interface is brought out to something other
than the CPU.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".
This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.
Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA drivers are calling phy_init_eee if eee_enabled is true.
Move up this statement in the DSA layer to simplify the DSA drivers.
qca8k does not require to cache the ethtool_eee structures from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains initial support for the QCA8337 switch. It
will detect a QCA8337 switch, if present and declared in the DT.
Each port will be represented through a standalone net_device interface,
as for other DSA switches. CPU can communicate with any of the ports by
setting an IP@ on ethN interface. Most of the extra callbacks of the DSA
subsystem are already supported, such as bridge offloading, stp, fdb.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
