IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Fix a problem where 578xx-KR is unable to get link when connected to 1G link
partner. Two fixes were required:
One was to force CL37 sync_status low to prevent Warpcore from getting stuck in
CL73 parallel detect loop while link partner is sending.
Second fix was to enable auto-detect mode, thus allowing the Warpcore to select
the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73
when there's indication for it.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer that is used to pass doorbell offset to the userspace UIO
driver may contain nonzero value in older versions of bnx2x driver.
Userspace cannot easily tell whether it contains a valid doorbell
offset or not. With the added signature, userspace will only use
the doorbell offset if the signature is present.
Update version to 2.5.19.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-mdix currently only works if autoneg is enabled. This patch enables
auto-mdix all the time by setting a bit in a PHY register. Define
meaningful constants for this PHY registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not reset the advertisement register when the speed
is forced, leaving the default advertisement value of 10 Mbps. This does
not work with some link partners when the next patch enables auto-mdix.
Set advertisement register to 0 if the speed is forced.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 stepping silicon specific code
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the hardware specific init and management.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing structures
and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code
to Linux.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This PCI-E SR-IOV virtual function (VF) driver is dependant upon the
physical function (PF) driver (i40e) for nearly all of its hardware
configuration. Requests from the VF driver are passed to the PF using
the hardware's Admin Queue.
This patch contains the functionality for communicating with the PF
driver. Because of the delay inherent in this communications channel,
most of the replies from the PF driver are handled asynchronously. The
exceptions are the "send API version" and "get VF config" messages,
which busy-wait because they are done so early during init that
interrupts are not yet configured.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the ethtool interface and related functionality.
Since the VF driver is mostly unaware of link, much of that
functionality is unused. The driver implements ethtool hooks for
statistics, driver info, and some basic non-link-related driver
settings.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This file contains the transmit, receive, and NAPI functionality.
Some of the functions in this module are extracted from the i40e driver
but functions that are not appropriate for virtual function devices have
been removed.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the driver for the Intel(R) XL710 X710 Virtual Function.
This patch contains the main driver entry points, but does not include
transmit and receive or ethtool functionality, which are presented as
separate patches in this series.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state
detection) there are still spurious link-down events for some chips
where the false link-down events count go over a few hundreds.
This patch takes a more conservative approach and only looks at
link-down events where the link-down state is not combined with other
states (e.g. half/full speed, pending frames in SRAM or TX status
information valid). In all other cases we assume the link is up.
Tested on MCS7830CV-DA (USB ID 9710:7830).
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Michael Leun <lkml20120218@newton.leun.net>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ding Tianhong says:
====================
slight optimization of addr compare for net modules
This is the second patchset for slight optimization of address compare,
mainly for net tree, just following the Joe's opinion, it will help review
the code for maintainers and supports.
v2: Change some style for patch 2.
According Eric's suggestion, use the ether_addr_equal_64bits to instead
of ether_addr_equal for patch 19.
In fact, there are a lot of places which could use ether_addr_equal_64bits
to instead of ether_addr_equal, but not this time, thanks for Joe's
opinion.
v3: Change some style for patch 11/19:
(net: packetengines: slight optimization of addr compare).
Joe pointed out that is_broadcast_ether_addr(addr) would be appropriate here,
but this should be left alone and not in this patch, so fix it later.
In the patch (net: caif: slight optimization of addr compare), the operand for
memcmp is not mac address, so it is unsuitable to use the ether_addr_equal
to compare a non mac address, so remove the patch from the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal_64bits
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned to instead of memcmp.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Santosh Raspatur <santosh@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned to instead of memcmp.
Cc: Ariel Elior <ariele@broadcom.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/socket.c:99:0:
include/net/sock.h: In function ‘sock_rps_record_flow’:
include/net/sock.h:849:30: error: ‘const struct sock’ has no member named ‘sk_rxhash’
include/net/sock.h: In function ‘sock_rps_reset_flow’:
include/net/sock.h:854:29: error: ‘const struct sock’ has no member named ‘sk_rxhash’
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dst_set will use dst, if dst is NULL although is not a problem,
then goto the 'no_route' and free nskb, so do the skb_dst_set is pointless.
so move the skb_dst_set after dst check.
Remove the unnecessary initialization as well.
v2: fix the subject line because it would confuse people,
as pointed out by Daniel.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new attribute to support 64bit rates so that
tc can use them to break the 32bit limit.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TSO/GSO/GRO packets, skb->len doesn't represent
a precise amount of bytes on wire.
This patch replace skb->len with qdisc_pkt_len(skb)
which is more precise.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device tunneling offloads mode is vxlan do the following
- call SET_PORT with the relevant setting
- add DMFS steering vxlan rule for the device self and multicast mac addresses
of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP
- set relevant QPC fields in RSS context and RX ring QPs
- in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
which are marked for encapsulation such that the HW will segment them properly.
- in RX flow, read HW offloaded checksum for encapsulated packets from the CQE
- advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to facilitate development for netlink protocol dissector,
fill the unused field skb->pkt_type of the cloned skb with a hint
of the address space of the new owner (receiver) socket in the
notion of "to kernel" resp. "to user".
At the time we invoke __netlink_deliver_tap_skb(), we already have
set the new skb owner via netlink_skb_set_owner_r(), so we can use
that for netlink_is_kernel() probing.
In normal PF_PACKET network traffic, this field denotes if the
packet is destined for us (PACKET_HOST), if it's broadcast
(PACKET_BROADCAST), etc.
As we only have 3 bit reserved, we can use the value (= 6) of
PACKET_FASTROUTE as it's _not used_ anywhere in the whole kernel
and not supported anywhere, and packets of such type were never
exposed to user space, so there are no overlapping users of such
kind. Thus, as wished, that seems the only way to make both
PACKET_* values non-overlapping and therefore device agnostic.
By using those two flags for netlink skbs on nlmon devices, they
can be made available and picked up via sll_pkttype (previously
unused in netlink context) in struct sockaddr_ll. We now have
these two directions:
- PACKET_USER (= 6) -> to user space
- PACKET_KERNEL (= 7) -> to kernel space
Partial `ip a` example strace for sa_family=AF_NETLINK with
detected nl msg direction:
syscall: direction:
sendto(3, ...) = 40 /* to kernel */
recvmsg(3, ...) = 3404 /* to user */
recvmsg(3, ...) = 1120 /* to user */
recvmsg(3, ...) = 20 /* to user */
sendto(3, ...) = 40 /* to kernel */
recvmsg(3, ...) = 168 /* to user */
recvmsg(3, ...) = 144 /* to user */
recvmsg(3, ...) = 20 /* to user */
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should also deliver packets to nlmon devices when we are in
netlink_unicast_kernel(), and only one of the {src,dst} sockets
is user sk and the other one kernel sk. That's e.g. the case in
netlink diag, netlink route, etc. Still, forbid to deliver messages
from kernel to kernel sks.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman says:
====================
sctp: Consolidate and ratelimit deprecation warnings
The SCTP protocol has several deprecation warnings in its setsockopt path that
can be triggered by unprivlidged users. Since these are not ratelimited, we can
spam the logs quite easily here. Since these are all deprecation warnings, and
that type of warning isn't uncommon in the rest of the kernel, lets make a
common pr_warn_deprecated macro to produce somewhat generalized ratelimited
deprecation warnings easily
====================
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a recent discussion regarding some sctp socket options, it was noted that
we have several points at which we issue log warnings that can be flooded at an
unbounded rate by any user. Fix this by converting all the pr_warns in the
sctp_setsockopt path to be pr_warn_ratelimited.
Note there are several debug level messages as well. I'm leaving those alone,
as, if you turn on pr_debug, you likely want lots of verbosity.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
