IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The patch prevents beacon misses in some case of
heavy load on a system.
If a beacon can't be transmitted directly from an
SWBA event it will be left in arvif->beacon and
transmission will be retried once TX credits
become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be necessary for further changes in
command submission scheme.
Once HTC is cleaned up WMI commands will finally
block.
This requires for SWBA to be processed in a
non-atomic context for now. Once other necessary
changes are in this will be reverted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.
To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:
[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95
Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mgmt_rx event structure has been expanded.
Since the structure header is expanded the payload
(i.e. mgmt frame) is shifted by a few bytes. This
needs to be taken into account in order to support
both old and new firmware.
This introduces a fw_features to keep track of any
FW-related ABI/behaviour changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This implements a limited subset of what can be
reported in the survey dump.
This can be used for assessing approximate channel
load, e.g. for automatic channel selection.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now ath10k assumed 3 spatial streams.
However some devices support only 2 spatial
streams.
This patch improves performance on devices that
don't support 3 spatial streams.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Restart the hardware if FW crashes.
If FW crashes during recovery we leave the
hardware in a "wedged" state to avoid recursive
recoveries.
When in "wedged" state userspace may bring
interfaces down (to issue stop()) and then bring
one interface (to issue start()) to reload
hardware manually.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different FW versions may provide different
functions thus mean different hw capabilities
advertised to mac80211.
It is safe to swap firmware files on disk during
driver/device runtime without worries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split up fw-related and hw-related suspension code.
Although we don't advertise WoW support to
mac80211 yet it's useful to keep the code in
suspend/resume hooks.
At this point there's no need to keep pci pm ops.
In case of WoW mac80211 calls ath10k_suspend()
which should take care of entering low-power mode.
In case WoW is not available mac80211 will go
through regular interface teradown and use start/stop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain notification hook can be called
regardless of the hw state (i.e. before start
mac80211 callback).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enables code reuse for proper hw reconfiguration
that is in turn required for proper
suspend/hibernation/wowlan support.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
