IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add IFLA_BOND_MIIMON to allow get/set of bonding parameter
miimon via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to netconf to show changes to proxy-arp status on a per
interface basis via netlink in a manner similar to forwarding
and reverse path state.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the GRO stack to avoid the use of "network_header"
and associated macros like ip_hdr() and ipv6_hdr() in order to allow
an arbitary number of IP hdrs (v4 or v6) to be used in the
encapsulation chain. This lays the foundation for various IP
tunneling support (IP-in-IP, GRE, VXLAN, SIT,...) to be added later.
With this patch, the GRO stack traversing now is mostly based on
skb_gro_offset rather than special hdr offsets saved in skb (e.g.,
skb->network_header). As a result all but the top layer (i.e., the
the transport layer) must have hdrs of the same length in order for
a pkt to be considered for aggregation. Therefore when adding a new
encap layer (e.g., for tunneling), one must check and skip flows
(e.g., by setting NAPI_GRO_CB(p)->same_flow to 0) that have a
different hdr length.
Note that unlike the network header, the transport header can and
will continue to be set by the GRO code since there will be at
most one "transport layer" in the encap chain.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now macvlan and macvtap use the same receive and
forward handlers, we can remove them completely and use
netif_rx and dev_forward_skb() directly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4191 states in 3.5:
When a host avoids using any non-reachable router X and instead sends
a data packet to another router Y, and the host would have used
router X if router X were reachable, then the host SHOULD probe each
such router X's reachability by sending a single Neighbor
Solicitation to that router's address. A host MUST NOT probe a
router's reachability in the absence of useful traffic that the host
would have sent to the router if it were reachable. In any case,
these probes MUST be rate-limited to no more than one per minute per
router.
Currently, when the neighbour corresponding to a router falls into
NUD_FAILED, it's never considered again. Introduce a new rt6_nud_state
value, RT6_NUD_FAIL_PROBE, which suggests the route should not be used but
should be probed with a single NS. The probe is ratelimited by the existing
code. To better distinguish meanings of the failure values, rename
RT6_NUD_FAIL_SOFT to RT6_NUD_FAIL_DO_RR.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Help of this function says: "in_dev: only on this interface, 0=any interface",
but since commit 39a6d06300 ("[NETNS]: Process inet_confirm_addr in the
correct namespace."), the code supposes that it will never be NULL. This
function is never called with in_dev == NULL, but it's exported and may be used
by an external module.
Because this patch restore the ability to call inet_confirm_addr() with in_dev
== NULL, I partially revert the above commit, as suggested by Julian.
CC: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC is currently using the field 'af_packet_priv' in struct net_device
as a handle to find the bearer instance associated to the given network
device. But, by doing so it is blocking other networking cleanups, such
as the one discussed here:
http://patchwork.ozlabs.org/patch/178044/
This commit removes this usage from TIPC. Instead, we introduce a new
field, 'tipc_ptr', to the net_device structure, to serve this purpose.
When TIPC bearer is enabled, the bearer object is associated to
'tipc_ptr'. When a TIPC packet arrives in the recv_msg() upcall
from a networking device, the bearer object can now be obtained from
'tipc_ptr'. When a bearer is disabled, the bearer object is detached
from its underlying network device by setting 'tipc_ptr' to NULL.
Additionally, an RCU lock is used to protect the new pointer.
Henceforth, the existing tipc_net_lock is used in write mode to
serialize write accesses to this pointer, while the new RCU lock is
applied on the read side to ensure that the pointer is 100% valid
within its wrapped area for all readers.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't needlessly recompute 'opt[opt_iter + 1]' as we already have it
stored in 'tag_len'.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And use it if possible.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tclass information in now already stored in rcv_flowinfo
We do not need to store the same information twice.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of IPV6_FLOWINFO only gives a
result if pktoptions is available (thanks to the
ip6_datagram_recv_ctl function).
It gives inconsistent results to user space, sometimes
there is a result for getsockopt(IPV6_FLOWINFO), sometimes
not.
This patch add rcv_flowinfo to store it, and return it to
the userspace in the same way than other pkt_options.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
several is_<foo>_ether_addr functions can be slightly
improved by using u32 dereferences.
I believe all current uses of is_zero_ether_addr and
is_broadcast_ether_addr are u16 aligned, so always use
u16 references to improve those functions performance.
Document the u16 alignment requirements.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic routine to test if possibly unaligned
to u16 Ethernet addresses are equal.
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
this uses the slightly faster generic routine
ether_addr_equal, otherwise this uses memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the behaviour similar to ipv4. This will allow user to set sysctl
default neigh param values and these values will be respected even by
devices registered before (that ones what do not have address set yet).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously inet devices were only constructed when addresses are added.
Therefore the default neigh parms values they get are the ones at the
time of these operations.
Now that we're creating inet devices earlier, this changes the behaviour
of default neigh parms values in an incompatible way (see bug #8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Introduced by:
commit 8030f54499
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Thu Feb 22 01:53:47 2007 +0900
[IPV4] devinet: Register inetdev earlier.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be needed later on to provide better management of default values.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the neigh param members to an array. This allows easier
manipulation which will be needed later on to provide better management of
default values.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library already reads the MII_STAT1000 and MII_LPA registers in
genphy_read_status(), so extend it to also populate the PHY device link
partner advertised features such that we can feed this back into ethtool
when asked for it in phy_ethtool_gset().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a PACKET_QDISC_BYPASS socket option, that
allows for using a similar xmit() function as in pktgen instead
of taking the dev_queue_xmit() path. This can be very useful when
PF_PACKET applications are required to be used in a similar
scenario as pktgen, but with full, flexible packet payload that
needs to be provided, for example.
On default, nothing changes in behaviour for normal PF_PACKET
TX users, so everything stays as is for applications. New users,
however, can now set PACKET_QDISC_BYPASS if needed to prevent
own packets from i) reentering packet_rcv() and ii) to directly
push the frame to the driver.
In doing so we can increase pps (here 64 byte packets) for
PF_PACKET a bit:
# CPUs -- QDISC_BYPASS -- qdisc path -- qdisc path[**]
1 CPU == 1,509,628 pps -- 1,208,708 -- 1,247,436
2 CPUs == 3,198,659 pps -- 2,536,012 -- 1,605,779
3 CPUs == 4,787,992 pps -- 3,788,740 -- 1,735,610
4 CPUs == 6,173,956 pps -- 4,907,799 -- 1,909,114
5 CPUs == 7,495,676 pps -- 5,956,499 -- 2,014,422
6 CPUs == 9,001,496 pps -- 7,145,064 -- 2,155,261
7 CPUs == 10,229,776 pps -- 8,190,596 -- 2,220,619
8 CPUs == 11,040,732 pps -- 9,188,544 -- 2,241,879
9 CPUs == 12,009,076 pps -- 10,275,936 -- 2,068,447
10 CPUs == 11,380,052 pps -- 11,265,337 -- 1,578,689
11 CPUs == 11,672,676 pps -- 11,845,344 -- 1,297,412
[...]
20 CPUs == 11,363,192 pps -- 11,014,933 -- 1,245,081
[**]: qdisc path with packet_rcv(), how probably most people
seem to use it (hopefully not anymore if not needed)
The test was done using a modified trafgen, sending a simple
static 64 bytes packet, on all CPUs. The trick in the fast
"qdisc path" case, is to avoid reentering packet_rcv() by
setting the RAW socket protocol to zero, like:
socket(PF_PACKET, SOCK_RAW, 0);
Tradeoffs are documented as well in this patch, clearly, if
queues are busy, we will drop more packets, tc disciplines are
ignored, and these packets are not visible to taps anymore. For
a pktgen like scenario, we argue that this is acceptable.
The pointer to the xmit function has been placed in packet
socket structure hole between cached_dev and prot_hook that
is hot anyway as we're working on cached_dev in each send path.
Done in joint work together with Jesper Dangaard Brouer.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need it elsewhere, move the inline helper function of
skb_needs_linearize() over to skbuff.h include file. While
at it, also convert the return to 'bool' instead of 'int'
and add a proper kernel doc.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6da7c8fcbc ("qdisc: allow setting default queuing discipline")
added the ability to change default qdisc from pfifo_fast to say fq
But as most modern ethernet devices are multiqueue, we cant really
see all the statistics from "tc -s qdisc show", as the default root
qdisc is mq.
This patch adds the calls to qdisc_list_add() to mq and mqprio
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new check for CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to reduce
the number of or's used in the ether_addr_equal comparison to very
slightly improve function performance.
Simplify the ether_addr_equal_64bits implementation.
Integrate and remove the zap_last_2bytes helper as it's now
used only once.
Remove the now unused compare_ether_addr function.
Update the unaligned-memory-access documentation to remove the
compare_ether_addr description and show how unaligned accesses
could occur with ether_addr_equal.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating an address with this flag set will result in kernel taking care
of temporary addresses in the same way as if the address was created by
kernel itself (after RA receive). This allows userspace applications
implementing the autoconfiguration (NetworkManager for example) to
implement ipv6 addresses privacy.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no more space in u8 ifa_flags. So do what davem suffested and
add another netlink attr called IFA_FLAGS for carry more flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers use dev_kfree_skb_any() and dev_kfree_skb_irq()
helpers to free skbs, both for dropped packets and TX completed ones.
We need to separate the two causes to get better diagnostics
given by dropwatch or "perf record -e skb:kfree_skb"
This patch provides two new helpers, dev_consume_skb_any() and
dev_consume_skb_irq() to be used for consumed skbs.
__dev_kfree_skb_irq() is slightly optimized to remove one
atomic_dec_and_test() in fast path, and use this_cpu_{r|w} accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breakdown the PHY_*_FEATURES into per speed defines such that we can
easily re-use them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for the 3.14 stream...
For the mac80211 bits, Johannes says:
"I have various improvements/cleanups/fixes all over, but the shortlog
shows that Luis's regulatory work and mesh work from the cozybit folks
are the biggest ones, along with the CSA fixes."
Along with that, we have big batches of updates to brcmfmac, rtlwifi,
and ath9k. There are updates to wcn36xx, rt2x00, and a handful of
others as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.
Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)
If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.
This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.
The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.
Using FQ/pacing is a way to increase the probability of
autocorking being triggered.
Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)
Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.
Tested:
Interesting effects when using line buffered commands under ssh.
Excellent performance results in term of cpu usage and total throughput.
lpq83:~# echo 1 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
9410.39
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
35209.439626 task-clock # 2.901 CPUs utilized
2,294 context-switches # 0.065 K/sec
101 CPU-migrations # 0.003 K/sec
4,079 page-faults # 0.116 K/sec
97,923,241,298 cycles # 2.781 GHz [83.31%]
51,832,908,236 stalled-cycles-frontend # 52.93% frontend cycles idle [83.30%]
25,697,986,603 stalled-cycles-backend # 26.24% backend cycles idle [66.70%]
102,225,978,536 instructions # 1.04 insns per cycle
# 0.51 stalled cycles per insn [83.38%]
18,657,696,819 branches # 529.906 M/sec [83.29%]
91,679,646 branch-misses # 0.49% of all branches [83.40%]
12.136204899 seconds time elapsed
lpq83:~# echo 0 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
6624.89
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
40045.864494 task-clock # 3.301 CPUs utilized
171 context-switches # 0.004 K/sec
53 CPU-migrations # 0.001 K/sec
4,080 page-faults # 0.102 K/sec
111,340,458,645 cycles # 2.780 GHz [83.34%]
61,778,039,277 stalled-cycles-frontend # 55.49% frontend cycles idle [83.31%]
29,295,522,759 stalled-cycles-backend # 26.31% backend cycles idle [66.67%]
108,654,349,355 instructions # 0.98 insns per cycle
# 0.57 stalled cycles per insn [83.34%]
19,552,170,748 branches # 488.244 M/sec [83.34%]
157,875,417 branch-misses # 0.81% of all branches [83.34%]
12.130267788 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: netfilter@vger.kernel.org
CC: Pablo Neira Ayuso <pablo@netfilter.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kill memcg_tcp_enter_memory_pressure. The only function of
memcg_tcp_enter_memory_pressure was to reduce deal with the
unnecessary abstraction that was tcp_memcontrol. Now that struct
tcp_memcontrol is gone remove this unnecessary function, the
unnecessary function pointer, and modify sk_enter_memory_pressure to
set this field directly, just as sk_leave_memory_pressure cleas this
field directly.
This fixes a small bug I intruduced when killing struct tcp_memcontrol
that caused memcg_tcp_enter_memory_pressure to never be called and
thus failed to ever set cg_proto->memory_pressure.
Remove the cg_proto enter_memory_pressure function as it now serves
no useful purpose.
Don't test cg_proto->memory_presser in sk_leave_memory_pressure before
clearing it. The test was originally there to ensure that the pointer
was non-NULL. Now that cg_proto is not a pointer the pointer does not
matter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to detect fragments in checksum_setup() was missing for IPv4 and
too eager for IPv6. (It transpires that Windows seems to send IPv6 packets
with a fragment header even if they are not a fragment - i.e. offset is zero,
and M bit is not set).
This patch also incorporates a fix to callers of maybe_pull_tail() where
skb->network_header was being erroneously added to the length argument.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
cc: David Miller <davem@davemloft.net>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 018c5bba05.
It causes regressions for people using chips driven by the sungem
driver. Suspicion is that the skb->csum value isn't being adjusted
properly.
The change also has a bug in that if __pskb_trim() fails, we'll leave
a corruped skb->csum value in there. We would really need to revert
it to it's original value in that case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
Pull scheduler fixes from Ingo Molnar:
"Various smaller fixlets, all over the place"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Fix generation of device-drivers
sched: Expose preempt_schedule_irq()
sched: Fix a trivial typo in comments
sched: Remove unused variable in 'struct sched_domain'
sched: Avoid NULL dereference on sd_busy
sched: Check sched_domain before computing group power
MAINTAINERS: Update file patterns in the lockdep and scheduler entries
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit.
While at it, split 5 and 10 MHz capability flags in case we ever need
to support hardware that can only do one of the two.
Also move the flag settings to the split-only information so we don't
increase the space needed for old userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change location of flag setting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
