IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
For calculating the HDA DMA format, use the max_bps supported by the
DAI caps instead of fixing it to 32/24. For host DMA the Max bps support
is 32, but in case of link DMA, this depends on the codec capability.
So use the sig_bits to define the bps supported by dai.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
KPB module default parameter were overwritten by the dynamic instance
id once use case is executed. This will cause module crash from
subsequent execution of use case as the updated parameters are used.
So instead of over writing the default parameter, make a copy and
update the module parameter and use this in IPC message.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Kranthikumar, GudishaX <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When module size > DMA buffer size, driver copies first chunk and waits
for the BDL complete interrupt. BDL complete interrupt never occurs and
wait time expires as module load IPC is not send to start the DMA from
DSP.
To fix the above issue need to follow the below steps:
1. After copying the first chunk, send the module load IPC to start the
DMA.
2. Wait for the BDL interrupt. Once interrupt is received, copy the
next chunk.
3. Continue step 2 till all bytes are copied.
4. When all the bytes are copied (bytes_left = 0), wait for module load
IPC response
5. Handled module load IPC response messages, check the load module IPC
response and wake up the thread to complete module load.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dsp ops is already set in init, so use this in cleanup routine
instead of again retrieving it. Also constify struct skl_dsp_ops.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP firmware sends notification every 1ms, which is disabled in runtime
suspend. But if a system has no runtime pm, we keep getting
notification, so disable after FW init as well.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove BE prepare ops which enables MCLK by default. If MCLK is required
to be enabled for any specific platform, it needs to be enabled in the
corresponding machine driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If D3 IPC fails or times out, firmware needs to be reloaded as driver
continues the reset.
So set the fw_load flag to false to reload the firmware in D0.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In system suspend, firmware needs to be re-downloaded as IMR is cleared.
When firmware is downloaded in D0, core state is not set to running
state causing instability with subsequent D0-D3 cycles.
So set the core state correctly during D0 and check the DSP core state
if not in reset to set the DSP to D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DSP is in D3, no interrupts are expected, so disable
interrupt while entering D3.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the widget is a mixin module, just unbind between source and sink
and don't stop the source pipe as there can be multiple sinks
connected.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe needs to stopped before deleting the pipe. Currently check is
for pipe state > STARTED, which is incorrect. So changed to include
pipe state STARTED to stop the pipe if it started.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a commit 4cd9899f0d16 ("ASoC: Intel: Skylake: Add multiple pin
formats") describes, 'fixups is applied to pin 0 only'. On the other
hand, the commit left some codes as what they were. This might
confuses readers.
This commit fixes the issue. This doesn't change driver behaviour at all.
Fixes: 4cd9899f0d16 ("ASoC: Intel: Skylake: Add multiple pin formats")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 'include/linux/kernel.h', there's a helper macro to round numerical
value. Let's use it.
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 'skl_tplg_set_module_init_data()', a pointer to 'params' member of
'struct skl_algo_data' is calculated, then casted to (u32 *) and assigned
to a member of configuration data. The configuration data is passed to the
other functions and used to process intel IPC. In this processing, the
value of member is used to get message data, however this can bring invalid
memory access in 'skl_set_module_params()' as a result of calculation of
a pointer for actual message data.
(sound/soc/intel/skylake/skl-topology.c)
skl_tplg_init_pipe_modules()
->skl_tplg_set_module_init_data() (has this bug)
->skl_tplg_set_module_params()
(sound/soc/intel/skylake/skl-messages.c)
->skl_set_module_params()
((char *)param) + data_offset
This commit fixes the bug.
Fixes: abb740033b56 ("ASoC: Intel: Skylake: Add support to configure module params")
Signed-off-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.5+
During S3->S0 transition, sometime ROM init fails because of
authentication engine loads later than the OS. In this case driver
waits for a longer period and then retries the FW download causing
huge delay in resume time of audio device.
To avoid this, ROM INIT wait time is set to a optimal value and
increased the retries for firmware download.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the DSP firmware/library at boot, so that for S3 to S0 transition
use the stored ctx for downloading the firmware to DSP memory.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch create entry in sysfs file system to report the
platform_id = "pci-id-oem_id-oem_table_id-oem_revision"
for board identification.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA channel(stream tag) used by the HDA link need to programmed in
codec so that codec receives packet from the link associated with the
same channel.
DMA channel is allocated in link BE dai hw_params, the same needs to be
set for the BE codec dai. Instead of using get/set dma_data(), use
dai_ops snd_soc_dai_set_tdm_slot() to set the stream tag.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In system suspend, the firmware pipelines will be deleted and there
is no need to save the pipeline context. Driver will save the DPIB and
LPIB pointers in suspend.
In system resume, the firmware pipelines will be created again and the
RD/RW pointers in the Firmware buffer points to the base address. So
need to fetch the non-played data again to firmware buffer. LPIB
indicates the HW rendered position.
Instead of setting DPIB as resume point, set it to LPIB to restore from
the HW render position so that DMA would fetch the non-played data one
more time.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipe is pass-through, BE and FE modules are defined inside
a pipe, reset of pipe will be done in FE DAI prepare. So don't
reset in the BE prepare.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Saved firmware ctx was not never released, so release Firmware
ctx in cleanup routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the optimized dsp_register_poll API to poll the DSP firmware
status register rather than open coding it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing the topology manifest info directly to IPC library,
define the manifest info in topology and use this in IPC Library.
This will remove the dependency on topology interface definition with
IPC library.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is not available in a pipeline, fail safely rather than
causing oops.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed the unused function skl_get_format as the format is calculated
directly using the HDA core API.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds helper function to configure the host/link DMA when
the DMA is in decoupled mode.
Next patch adds the usage of this helper routines for configuring
DMA in Mixer event handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system is suspended when PCM was paused/stopped, restart doesn't
configure DMA as it is we are in Pause state and results in IO error
eventually.
Configure host/link DMA before initializing DSP Gateway copier module
instead of DAI prepare(). So moved DMA configuration to mixer PRE_PMD
widget handler instead of DAI prepare.
This uses previously added new API to do the configuration and removes
old DAI prepare code.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To configure Host/Link DMA, additionally link index and format
are required based on the hw params. So added these parameters in
the pipe params and in hw_params the pipe params are updated.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In skl_tplg_mixer_dapm_post_pmd_event(), a variable 'ret' is initialized but
not used.
We don't check return of skl_delete_pipe, so remove the assignment as
well, so remove this variable.
sound/soc/intel/skylake/skl-topology.c: In function ‘skl_tplg_mixer_dapm_post_pmd_event’:
sound/soc/intel/skylake/skl-topology.c:976:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret = 0;
^
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that I2S conflig blob structure is no longer in use, remove it.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S blob config structure can change between DSP copier module versions.
We are not modifying these structures anyway and NHLT blobs specify them
properly, so use the blob directly to send the dma_control ipc instead
of using the predefined I2S blob config structure.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to suspend, if we have any pending D0i3 work scheduled,
flush that and force the DSP to goto D0i3 mode before going to suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were invoking pci_disable_device() while going to suspend-to-idle and
pci_enable_device() while coming back to active state.
Turns out that we do not need these calls as we only need system to be
wake capable when in suspend-to-idle state. The wake capability is
already done by enable_irq_wake() calls, so remove these unwanted calls
in driver.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver needs two DSP callback, one to set D0i0 (active) and D0i3
(low-power) states.
Add these callbacks in dsp ops and implement them for broxton platforms.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To set the controller in D0i3 mode, the driver needs to set D0i3C
register after DSP is quiesced. Since the D0iX entry/exit is done by IPC,
add this as callback so that it can be invoked from IPC module.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio DSP supports intermediate power states between D0 and D3
states. These states are D0i0 and D0i3 states.
Collectively we refer these two states as D0iX states.
To set or wake up from these states, driver also needs to send an IPC "Set D0iX
IPC" before doing anything else.
Add support for this new IPC messages.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI codec is required to be powered up before controller initialization
for successful enumeration of codec. If the probe fails it needs to be
powered off to balance the power state of HDMI codec.
This fix balances the reference count in the error path before turning
off the codec.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"*val" is a u64. It definitely looks like we intend to use the high 32
bits as well.
Fixes: 700a9a63f9c1 ("ASoC: Intel: Skylake: Add module instance id generation APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_probe() releases a runtime pm ref unconditionally wheras
skl_remove() acquires one only if the device is wakeup capable.
Thus if the device is not wakeup capable, unloading and reloading
the module will result in the refcount being decreased below 0.
Fix it.
Fixes: d8c2dab8381d ("ASoC: Intel: Add Skylake HDA audio driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
