IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
MCP23017 is an IO expander offering 16 input/output port expander with
interrupt output.
On stm32mp135f-dk, only INTA is routed (on PG12), but MCP23017 can mirror
the bank B interrupts on INTA, that's why the property microchip,irq-mirror
is used.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The USB OTG controller provides the USB data available on stm32mp135f-dk,
on the Type-C connector. Data role is determined by "usb-role-switch".
A STM32G0 provides the USB Type-C and Power Delivery connectivity.
It controls dual role power and dual role data through UCSI protocol over
I2C. It's wired on I2C1, with an interrupt pin on PI2 GPIO.
Its firmware maybe updated over I2C, so use the optional firmware-name
to enable firmware update.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
USBH Host EHCI controller manages the USB High-Speed hub controller IC
offering Type-A CN5 & CN6 connectors available on stm32mp135f-dk.
USB Host OHCI controller doesn't need to be enabled as Full-Speed and
Low-Speed traffic will be managed by the hub.
This USB2514B onboard hub is supplied by a 3v3 PMIC regulator.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
USBPHYC manages the two USB High-Speed phys. port0 is used by USBH and
port1 is used by USBOTG.
Enable and tune both PHYs on stm32mp135f-dk.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add VDD_USB and 3V3_SW regulators on stm32mp135f-dk. Temporary add them
as fixed regulators, waiting for full SCMI regulators support.
This is a precursor patch to enable USB support on STM32MP13:
- VDD_USB supplies the STM32MP13 USB internals
- 3V3_SW supplies various peripherals, including the onboard HUB.
Note: USB support requires these regulators to be enabled before
entering the kernel.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Configure ADC support on stm32mp135f-dk. ADC can be used for
USB Type-C CC1 & CC2 pins wired to in6 & in12.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add a dummy fixed regulator vdd-adc for STM32 ADC,
on STM32MP135F-DK board, while SCMI regulators are not available.
This patch will have to be removed when SCMI regulator support
is added to STM32MP13.
This patch intends to allow ADC enabling on STM32MP13.
With this patch the ADC can probe but it cannot return
valid conversion data, as it's regulator is not actually enabled.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add pinctrl information and a disabled spi5 node within
stm32mp135f-dk.dts in order to use the spi5 bus which is
available via the GPIO expansion pins of the STM32MP135 Discovery board.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enable the two i2c busses i2c1 and i2c5 available on the
stm32mp135f-dk Discovery board.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The PA13 user button is connected to the PA13 pin of the stm32mp135f-dk
board. It requires an internal pull-up configuration.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The blue led (Linux heartbeat) is connected to the PA14 pin of the
stm32mp135f-dk board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enables the support of RTC on stm32mp135f-dk board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
