IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pinconf_generic_dt_node_to_map() scans only subnodes of the pinctrl-0 pahndle,
not the referenced node itself. Change the example nodes to match.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document the GPIO/PINCONF device tree binding for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Scorpion supports a set of local performance monitor event
selection registers (LPM) sitting behind a cp15 based interface
that extend the architected PMU events to include Scorpion CPU
and Venum VFP specific events. To use these events the user is
expected to program the lpm register with the event code shifted
into the group they care about and then point the PMNx event at
that region+group combo by writing a LPMn_GROUPx event. Add
support for this hardware.
Note: the raw event number is a pure software construct that
allows us to map the multi-dimensional number space of regions,
groups, and event codes into a flat event number space suitable
for use by the perf framework.
This is based on code originally written by Sheetal Sahasrabudhe,
Ashwin Chaugule, and Neil Leeder [1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm/tree/arch/arm/kernel/perf_event_msm.c?h=msm-3.4
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Neil Leeder <nleeder@codeaurora.org>
Cc: Ashwin Chaugule <ashwinc@codeaurora.org>
Cc: Sheetal Sahasrabudhe <sheetals@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add documentation to the sound directory of the
device-tree bindings for the soundcard of the
Storm board.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the representation of the audio DSP, in the
LPASS CPU bindings description, from a required
subnode to an optional phandle.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the binding documentation for the Imagination Technologies hash
accelerator that provides hardware acceleration for SHA1/SHA224/SHA256/MD5
hashes. This hardware will be present in the upcoming pistachio SoC.
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a rather unpleasantly large set of bug fixes for arm-soc,
Most of them because of cross-tree dependencies for Exynos
where we should have figured out the right path to merge things
before the merge window, and then the maintainer being unable to
sort things out in time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile
express and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down
on Exynos5
- Multiple small OMAP power management fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Lr/j
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather unpleasantly large set of bug fixes for arm-soc, Most
of them because of cross-tree dependencies for Exynos where we should
have figured out the right path to merge things before the merge
window, and then the maintainer being unable to sort things out in
time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile express
and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down on Exynos5
- Multiple small OMAP power management fixes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: vexpress: update CONFIG_USB_ISP1760 option
ARM: digicolor: add the machine directory to Makefile
ARM: STi: Add STiH410 SoC support
MAINTAINERS: add Freescale Vybrid SoC
MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
...
Add a binding for the OMAP4/5 wake-up generator, which acts as
an interrupt controller feeding into the GIC.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Fix for stdout-path option parsing with added unittest
- Fix for stdout-path interaction with earlycon
- Several DT unittest fixes
- Fix Sparc allmodconfig build error on
of_platform_register_reconfig_notifier
- Several DT overlay kconfig and build warning fixes
- Several DT binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVAvyzAAoJEMhvYp4jgsXiKSAIALRxbtnjPu13+1vD6C8xcTsN
TsD/GoIOtBjVlEPDFrKXOhRXkxXbgONDSveQYhm0iWr30ECloVoikIxF2NPty2nR
B3xN7WbbmeEBl1ubGVw60xs/M1cF7d11UpjRabjlVqFpMll5LufX0+ZAbLQ+Brsl
5zSGxIonG8pRxFy0yi6++76cyywn3XVYoUTMb+nKaiSzXvOBhGnm5MXruiynVH9m
enVKop8rhizfUdvSHFfxxipFK9L3+EYx0yxaZWW9tvYh6yHhb/GZxQcuz1Rn5KUJ
wY0Y4PJdusLOO0FNprZmLsi3GxEXOIBS0bcPCXQAqD/Kr46waVOETajyIItMYnY=
=nyIQ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix for stdout-path option parsing with added unittest
- fix for stdout-path interaction with earlycon
- several DT unittest fixes
- fix Sparc allmodconfig build error on of_platform_register_reconfig_notifier
- several DT overlay kconfig and build warning fixes
- several DT binding documentation updates
* tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/platform: Fix sparc:allmodconfig build
of: unittest: Add options string testcase variants
of: fix handling of '/' in options for of_find_node_by_path()
of/unittest: Fix the wrong expected value in of_selftest_property_string
of/unittest: remove the duplicate of_changeset_init
dt: submitting-patches: clarify that DT maintainers are to be cced on bindings
of: unittest: fix I2C dependency
of/overlay: Remove unused variable
Documentation: DT: Renamed of-serial.txt to 8250.txt
of: Fix premature bootconsole disable with 'stdout-path'
serial: add device tree binding documentation for ETRAX FS UART
of/overlay: Directly include idr.h
of: Drop superfluous dependance for OF_OVERLAY
of: Add vendor prefix for Arasan
of: Add prompt for OF_OVERLAY config
To connect the channel of USB-DMAC to USBHS DnFIFO number, this patch
adds this channel/FIFO number in dma-names. Otherwise, this driver
needs to add analysis code for device tree.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support to STiH410 SoC.
Please note "st,stih410" is already present in device tree.
The problem is that it is missing the entry in the match table,
and so the L2 cache and other cpus than 0 don't get initialized.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The exact steps provided for submitting binding patches can be read
as requiring the bindings to be sent only to the devicetree@vger.kernel.org
list. Since the DT maintainers would like to be Cced on any binding
submissions, make this requirement explicit in step 2.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The file of-serial.txt was only for 8250 compatible UART implementations,
so renamed it to 8250.txt to avoid confusing other persons.
This is suggested by Arnd, see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/291455.html
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into HEAD
Linux 4.0-rc3
Merging in v4.0-rc3 because commit 30a22c215a00 (console: Fix
console name size mismatch) is a dependency.
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
The jz4780 and jz4740 have very similar i2s blocks.
The slight difference is in Rx/Tx fifos.
And the bitclocks for input/output are different.
This patch adds jz4780 support to the driver
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.
As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some boards, such as the LaCie 2Big Network v2 or 2Big NAS (based on
Marvell Kirkwood SoCs), an I2C fan controller is used but the alarm
signal is wired to a separate GPIO. Unfortunately, the gpio-fan driver
can't be used to handle GPIO alarm alone from DT: an error is returned
if the "gpios" DT property is missing.
This patch allows to use the gpio-fan driver even if the "alarm-gpios"
DT property is defined alone.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missing "cdns,at91sam9260-macb", "atmel,sama5d3-gem" and
"atmel,sama5d4-gem" compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing has revealed that the temperature in the rtp controller of the A10
(sun4i) SoC has a different curve then on the A13 (sun5i) and later models.
Add a new sun5i-a13-ts compatible to differentiate the newer models and
set the curve based on the compatible string.
The new curve is still not ideal on all A10-s, that seems to have to
do with there being a large spread between different A10-s out there,
the new curve us based on callibration results on 4 completely different
models:
raw min raw max temp min temp max stepsize offset
Tong Zhang's hackberry 2402 2680 45.0 80.0 0.125 -255.3
Hansg's Cubieboard 2207 2300 36.0 45.0 0.096 -175.8
Olliver's lime 1 (*): 2258 2537 48.3 87.1 0.139 -265.7
Olliver's lime 2 (*): 2222 2486 46.7 91.7 0.170 -331.0
*) from: http://linux-sunxi.org/Temperature_Calibration
Average all 4: 0.133 -257.0
Average without outliers (middle 2): 0.132 -261.0
Since it is better to slightly overreport the temperature this patch uses
the average of all 4 as curve.
This fixes the temperature reported on the A10 being much higher then
expected.
Reported-by: Tong Zhang <lovewilliam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other serial
driver bugfixes as well. Most notable is a wait_until_sent bugfix that
was traced back to being around since before 2.6.12 that Johan has fixed
up.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
zYYAn2w0uRndW+AqP4Tls54isRz6owpF
=gA2k
-----END PGP SIGNATURE-----
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Add binding documentation for CPU configuration and interrupt router
submodule of the Miscellaneous System Control Module. The MSCM is
used in all variants of Freescale Vybrid SoC's.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-3-git-send-email-stefan@agner.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull i2c fixes from Wolfram Sang:
"A set of updates and bugfixes for the new designware-baytrail driver.
And a documentation bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: add required clocks property to binding
i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
i2c: designware-baytrail: cross-check lock functions
i2c: designware-baytrail: fix sparse warnings
i2c: designware-baytrail: fix typo in error path
i2c: designware-baytrail: describe magic numbers
The act88600/act8846/act8865 regulators have a number of input supplies
supplying the individual regulators. This may even be recursively like on
most Rockchip boards using the act8846 where REG4 is most of the time
connected to the inl1-supply.
Therefore add the ability to specify the input supplies for the individual inputs.
The input-names are taken from the datasheets of act8600, act8846 and act8865.
On the act8600 some regulators do not have separate input supplies.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver supports reg-names, and Audio DMAC peri peri.
This patch adds sample code for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
