IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.
Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During bi-directional stress on some 82566/82567 devices, some received
packets were dropped. Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM. However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME). Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.
The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Otherwise (on sparc64):
drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full. Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable RPS by default. Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.
v2: added ethtool command to query flow hashing behavior per Ben Hutchings
and changed the type of rsskey to cleanup the setting of the register
array and avoid unnecessary casts (as pointed out by Joe Perches).
The long error messages are not changed since there is nothing in
the kernel ./Documentation that suggests the preferred method for
dealing with long messages other than to never break strings; leaving
them as-is for now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
e1000_rx_checksum() instead of in each call to the function
v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes sparse warnings:
drivers/net/ethernet/intel/ixgbevf/vf.c:418:21: warning: symbol 'ixgbevf_82599_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/vf.c:423:21: warning: symbol 'ixgbevf_X540_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/mbx.c:331:29: warning: symbol 'ixgbevf_mbx_ops' was not declared. Should it be static?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This irq disable/enable pair used to wrap access to the driver's vlgrp
struct, which is no longer present. So, then, this could also so no longer
be present.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements support for ndo_get_fcoe_hbainfo()
call in the ixgbe driver.
This function will be called by the FCoE protocol stack to
obtain device specific information from the underlying
device configured to do FCoE.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to 82576_Datasheet.pdf, PHY setting is lost after PHY power down.
So resetting PHY is needed when recovering from PHY power down to set a default
setting to PHY register.
Owing to this lack, NIC doesn't link up in some rare situation.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the runtime power management framework to add basic runtime PM support
to the igb driver. Namely, make the driver suspend the device when the link
is off and set it up for generating a wakeup event after the link has been
detected again. This feature is disabled by default.
Based on e1000e's runtime PM code.
Changes since v1:
Don't suspend the device when shutting down the interface.
Avoid race between runtime suspending and ethtool operations.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A global variable is currently used to hold the virtual address of the
CE4100 MDIO base register address. Store the address in the e1000_hw
structure and update macros accordingly.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Steven Rostedt, e1000 has a lockdep splat added
during the recent merge window. The issue is that
cancel_delayed_work is called while holding our private mutex.
There is no reason that I can see to hold the mutex during pci
shutdown, it was more just paranoia that I put the mutex_lock
around the call to e1000_down.
In a quick survey lots of drivers handle locking differently when
being called by the pci layer. The assumption here is that we
don't need the mutexes' protection in this function because
the driver could not be unloaded while in the shutdown handler
which is only called at reboot or poweroff.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transitioning through an IEEE DCBX version from a CEE DCBX
and back (CEE->IEEE->CEE) may leave IEEE attributes programmed
in the hardware. DCB uses a bit field in the set routines to
determine which attributes PG, PFC, APP need to be reprogrammed.
This is needed because user flow allows queueing a series
of changes and then reprogramming the hardware with the
entire set in one operation.
When transitioning from IEEE DCBX mode back into CEE DCBX
mode the PG and PFC bits need to be set so the possibly
different CEE attributes get programmed into the device.
This patch fixes broken logic that was evaluating to 0
and never setting any bits. Further this removes some
checks for num_tc in set routines. This logic only worked
when the number of traffic classes and user priorities
were equal. This is no longer the case for X540 devices.
Besides we can trust user input in this case if the
device is incorrectly configured the DCB bandwidths will
be incorrectly mapped but no OOPs, BUG, or hardware
failure will occur.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The order of operations is important in DCBnl set_all(). When FCoE
is configured it uses the up2tc map to learn which queues to configure
the hardware offloads on. Therefore we need to setup the map before
configuring FCoE.
This is only seen when the both up2tc mappings and APP info are
configured simultaneously.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the DMA Coalescing feature parameters to account for
larger MTUs. Previously, sufficient space may not have been allocated in
the receive buffer, causing packet drop.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
