IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Testing has revealed the existence of a race condition where a XIVE
interrupt being shut down can be in one of the XIVE interrupt queues
(of which there are up to 8 per CPU, one for each priority) at the
point where free_irq() is called. If this happens, can return an
interrupt number which has been shut down. This can lead to various
symptoms:
- irq_to_desc(irq) can be NULL. In this case, no end-of-interrupt
function gets called, resulting in the CPU's elevated interrupt
priority (numerically lowered CPPR) never gets reset. That then
means that the CPU stops processing interrupts, causing device
timeouts and other errors in various device drivers.
- The irq descriptor or related data structures can be in the process
of being freed as the interrupt code is using them. This typically
leads to crashes due to bad pointer dereferences.
This race is basically what commit 62e0468650 ("genirq: Add optional
hardware synchronization for shutdown", 2019-06-28) is intended to
fix, given a get_irqchip_state() method for the interrupt controller
being used. It works by polling the interrupt controller when an
interrupt is being freed until the controller says it is not pending.
With XIVE, the PQ bits of the interrupt source indicate the state of
the interrupt source, and in particular the P bit goes from 0 to 1 at
the point where the hardware writes an entry into the interrupt queue
that this interrupt is directed towards. Normally, the code will then
process the interrupt and do an end-of-interrupt (EOI) operation which
will reset PQ to 00 (assuming another interrupt hasn't been generated
in the meantime). However, there are situations where the code resets
P even though a queue entry exists (for example, by setting PQ to 01,
which disables the interrupt source), and also situations where the
code leaves P at 1 after removing the queue entry (for example, this
is done for escalation interrupts so they cannot fire again until
they are explicitly re-enabled).
The code already has a 'saved_p' flag for the interrupt source which
indicates that a queue entry exists, although it isn't maintained
consistently. This patch adds a 'stale_p' flag to indicate that
P has been left at 1 after processing a queue entry, and adds code
to set and clear saved_p and stale_p as necessary to maintain a
consistent indication of whether a queue entry may or may not exist.
With this, we can implement xive_get_irqchip_state() by looking at
stale_p, saved_p and the ESB PQ bits for the interrupt.
There is some additional code to handle escalation interrupts
properly; because they are enabled and disabled in KVM assembly code,
which does not have access to the xive_irq_data struct for the
escalation interrupt. Hence, stale_p may be incorrect when the
escalation interrupt is freed in kvmppc_xive_{,native_}cleanup_vcpu().
Fortunately, we can fix it up by looking at vcpu->arch.xive_esc_on,
with some careful attention to barriers in order to ensure the correct
result if xive_esc_irq() races with kvmppc_xive_cleanup_vcpu().
Finally, this adds code to make noise on the console (pr_crit and
WARN_ON(1)) if we find an interrupt queue entry for an interrupt
which does not have a descriptor. While this won't catch the race
reliably, if it does get triggered it will be an indication that
the race is occurring and needs to be debugged.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100648.GE9567@blackberry
At present, when running a guest on POWER9 using HV KVM but not using
an in-kernel interrupt controller (XICS or XIVE), for example if QEMU
is run with the kernel_irqchip=off option, the guest entry code goes
ahead and tries to load the guest context into the XIVE hardware, even
though no context has been set up.
To fix this, we check that the "CAM word" is non-zero before pushing
it to the hardware. The CAM word is initialized to a non-zero value
in kvmppc_xive_connect_vcpu() and kvmppc_xive_native_connect_vcpu(),
and is now cleared in kvmppc_xive_{,native_}cleanup_vcpu.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100100.GC9567@blackberry
When a vCPU is brought done, the XIVE VP (Virtual Processor) is first
disabled and then the event notification queues are freed. When freeing
the queues, we check for possible escalation interrupts and free them
also.
But when a XIVE VP is disabled, the underlying XIVE ENDs also are
disabled in OPAL. When an END (Event Notification Descriptor) is
disabled, its ESB pages (ESn and ESe) are disabled and loads return all
1s. Which means that any access on the ESB page of the escalation
interrupt will return invalid values.
When an interrupt is freed, the shutdown handler computes a 'saved_p'
field from the value returned by a load in xive_do_source_set_mask().
This value is incorrect for escalation interrupts for the reason
described above.
This has no impact on Linux/KVM today because we don't make use of it
but we will introduce in future changes a xive_get_irqchip_state()
handler. This handler will use the 'saved_p' field to return the state
of an interrupt and 'saved_p' being incorrect, softlockup will occur.
Fix the vCPU cleanup sequence by first freeing the escalation interrupts
if any, then disable the XIVE VP and last free the queues.
Fixes: 90c73795af ("KVM: PPC: Book3S HV: Add a new KVM device for the XIVE native exploitation mode")
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190806172538.5087-1-clg@kaod.org
The XIVE device structure is now allocated in kvmppc_xive_get_device()
and kfree'd in kvmppc_core_destroy_vm(). In case of an OPAL error when
allocating the XIVE VPs, the kfree() call in kvmppc_xive_*create()
will result in a double free and corrupt the host memory.
Fixes: 5422e95103 ("KVM: PPC: Book3S HV: XIVE: Replace the 'destroy' method by a 'release' method")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6ea6998b-a890-2511-01d1-747d7621eb19@kaod.org
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XICS-on-XIVE KVM device needs to allocate XIVE event queues when a
priority is used by the OS. This is referred as EQ provisioning and it
is done under the hood when :
1. a CPU is hot-plugged in the VM
2. the "set-xive" is called at VM startup
3. sources are restored at VM restore
The kvm->lock mutex is used to protect the different XIVE structures
being modified but in some contexts, kvm->lock is taken under the
vcpu->mutex which is not permitted by the KVM locking rules.
Introduce a new mutex 'lock' for the KVM devices for them to
synchronize accesses to the XIVE device structures.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, kvmppc_xive_release() and kvmppc_xive_native_release() clear
kvm->arch.mmu_ready and call kick_all_cpus_sync() as a way of ensuring
that no vcpus are executing in the guest. However, future patches will
change the mutex associated with kvm->arch.mmu_ready to a new mutex that
nests inside the vcpu mutexes, making it difficult to continue to use
this method.
In fact, taking the vcpu mutex for a vcpu excludes execution of that
vcpu, and we already take the vcpu mutex around the call to
kvmppc_xive_[native_]cleanup_vcpu(). Once the cleanup function is
done and we release the vcpu mutex, the vcpu can execute once again,
but because we have cleared vcpu->arch.xive_vcpu, vcpu->arch.irq_type,
vcpu->arch.xive_esc_vaddr and vcpu->arch.xive_esc_raddr, that vcpu will
not be going into XIVE code any more. Thus, once we have cleaned up
all of the vcpus, we are safe to clean up the rest of the XIVE state,
and we don't need to use kvm->arch.mmu_ready to hold off vcpu execution.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to ensure that after a XIVE or XICS-on-XIVE KVM device
is closed, KVM will not try to enable or disable any of the escalation
interrupts for the VCPUs. We don't have to worry about races between
clearing the pointers and use of the pointers by the XIVE context
push/pull code, because the callers hold the vcpu->mutex, which is
also taken by the KVM_RUN code. Therefore the vcpu cannot be entering
or exiting the guest concurrently.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Now that we have the possibility of a XIVE or XICS-on-XIVE device being
released while the VM is still running, we need to be careful about
races and potential use-after-free bugs. Although the kvmppc_xive
struct is not freed, but kept around for re-use, the kvmppc_xive_vcpu
structs are freed, and they are used extensively in both the XIVE native
and XICS-on-XIVE code.
There are various ways in which XIVE code gets invoked:
- VCPU entry and exit, which do push and pull operations on the XIVE hardware
- one_reg get and set functions (vcpu->mutex is held)
- XICS hypercalls (but only inside guest execution, not from
kvmppc_pseries_do_hcall)
- device creation calls (kvm->lock is held)
- device callbacks - get/set attribute, mmap, pagefault, release/destroy
- set_mapped/clr_mapped calls (kvm->lock is held)
- connect_vcpu calls
- debugfs file read callbacks
Inside a device release function, we know that userspace cannot have an
open file descriptor referring to the device, nor can it have any mmapped
regions from the device. Therefore the device callbacks are excluded,
as are the connect_vcpu calls (since they need a fd for the device).
Further, since the caller holds the kvm->lock mutex, no other device
creation calls or set/clr_mapped calls can be executing concurrently.
To exclude VCPU execution and XICS hypercalls, we temporarily set
kvm->arch.mmu_ready to 0. This forces any VCPU task that is trying to
enter the guest to take the kvm->lock mutex, which is held by the caller
of the release function. Then, sending an IPI to all other CPUs forces
any VCPU currently executing in the guest to exit.
Finally, we take the vcpu->mutex for each VCPU around the process of
cleaning up and freeing its XIVE data structures, in order to exclude
any one_reg get/set calls.
To exclude the debugfs read callbacks, we just need to ensure that
debugfs_remove is called before freeing any data structures. Once it
returns we know that no CPU can be executing the callbacks (for our
kvmppc_xive instance).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a P9 sPAPR VM boots, the CAS negotiation process determines which
interrupt mode to use (XICS legacy or XIVE native) and invokes a
machine reset to activate the chosen mode.
We introduce 'release' methods for the XICS-on-XIVE and the XIVE
native KVM devices which are called when the file descriptor of the
device is closed after the TIMA and ESB pages have been unmapped.
They perform the necessary cleanups : clear the vCPU interrupt
presenters that could be attached and then destroy the device. The
'release' methods replace the 'destroy' methods as 'destroy' is not
called anymore once 'release' is. Compatibility with older QEMU is
nevertheless maintained.
This is not considered as a safe operation as the vCPUs are still
running and could be referencing the KVM device through their
presenters. To protect the system from any breakage, the kvmppc_xive
objects representing both KVM devices are now stored in an array under
the VM. Allocation is performed on first usage and memory is freed
only when the VM exits.
[paulus@ozlabs.org - Moved freeing of xive structures to book3s.c,
put it under #ifdef CONFIG_KVM_XICS.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The KVM XICS-over-XIVE device and the proposed KVM XIVE native device
implement an IRQ space for the guest using the generic IPI interrupts
of the XIVE IC controller. These interrupts are allocated at the OPAL
level and "mapped" into the guest IRQ number space in the range 0-0x1FFF.
Interrupt management is performed in the XIVE way: using loads and
stores on the addresses of the XIVE IPI interrupt ESB pages.
Both KVM devices share the same internal structure caching information
on the interrupts, among which the xive_irq_data struct containing the
addresses of the IPI ESB pages and an extra one in case of pass-through.
The later contains the addresses of the ESB pages of the underlying HW
controller interrupts, PHB4 in all cases for now.
A guest, when running in the XICS legacy interrupt mode, lets the KVM
XICS-over-XIVE device "handle" interrupt management, that is to
perform the loads and stores on the addresses of the ESB pages of the
guest interrupts. However, when running in XIVE native exploitation
mode, the KVM XIVE native device exposes the interrupt ESB pages to
the guest and lets the guest perform directly the loads and stores.
The VMA exposing the ESB pages make use of a custom VM fault handler
which role is to populate the VMA with appropriate pages. When a fault
occurs, the guest IRQ number is deduced from the offset, and the ESB
pages of associated XIVE IPI interrupt are inserted in the VMA (using
the internal structure caching information on the interrupts).
Supporting device passthrough in the guest running in XIVE native
exploitation mode adds some extra refinements because the ESB pages
of a different HW controller (PHB4) need to be exposed to the guest
along with the initial IPI ESB pages of the XIVE IC controller. But
the overall mechanic is the same.
When the device HW irqs are mapped into or unmapped from the guest
IRQ number space, the passthru_irq helpers, kvmppc_xive_set_mapped()
and kvmppc_xive_clr_mapped(), are called to record or clear the
passthrough interrupt information and to perform the switch.
The approach taken by this patch is to clear the ESB pages of the
guest IRQ number being mapped and let the VM fault handler repopulate.
The handler will insert the ESB page corresponding to the HW interrupt
of the device being passed-through or the initial IPI ESB page if the
device is being removed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These controls will be used by the H_INT_SET_QUEUE_CONFIG and
H_INT_GET_QUEUE_CONFIG hcalls from QEMU to configure the underlying
Event Queue in the XIVE IC. They will also be used to restore the
configuration of the XIVE EQs and to capture the internal run-time
state of the EQs. Both 'get' and 'set' rely on an OPAL call to access
the EQ toggle bit and EQ index which are updated by the XIVE IC when
event notifications are enqueued in the EQ.
The value of the guest physical address of the event queue is saved in
the XIVE internal xive_q structure for later use. That is when
migration needs to mark the EQ pages dirty to capture a consistent
memory state of the VM.
To be noted that H_INT_SET_QUEUE_CONFIG does not require the extra
OPAL call setting the EQ toggle bit and EQ index to configure the EQ,
but restoring the EQ state will.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This control will be used by the H_INT_SET_SOURCE_CONFIG hcall from
QEMU to configure the target of a source and also to restore the
configuration of a source when migrating the VM.
The XIVE source interrupt structure is extended with the value of the
Effective Interrupt Source Number. The EISN is the interrupt number
pushed in the event queue that the guest OS will use to dispatch
events internally. Caching the EISN value in KVM eases the test when
checking if a reconfiguration is indeed needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The XIVE KVM device maintains a list of interrupt sources for the VM
which are allocated in the pool of generic interrupts (IPIs) of the
main XIVE IC controller. These are used for the CPU IPIs as well as
for virtual device interrupts. The IRQ number space is defined by
QEMU.
The XIVE device reuses the source structures of the XICS-on-XIVE
device for the source blocks (2-level tree) and for the source
interrupts. Under XIVE native, the source interrupt caches mostly
configuration information and is less used than under the XICS-on-XIVE
device in which hcalls are still necessary at run-time.
When a source is initialized in KVM, an IPI interrupt source is simply
allocated at the OPAL level and then MASKED. KVM only needs to know
about its type: LSI or MSI.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The user interface exposes a new capability KVM_CAP_PPC_IRQ_XIVE to
let QEMU connect the vCPU presenters to the XIVE KVM device if
required. The capability is not advertised for now as the full support
for the XIVE native exploitation mode is not yet available. When this
is case, the capability will be advertised on PowerNV Hypervisors
only. Nested guests (pseries KVM Hypervisor) are not supported.
Internally, the interface to the new KVM device is protected with a
new interrupt mode: KVMPPC_IRQ_XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This creates an alternative guest entry/exit path which is used for
radix guests on POWER9 systems when we have indep_threads_mode=Y. In
these circumstances there is exactly one vcpu per vcore and there is
no coordination required between vcpus or vcores; the vcpu can enter
the guest without needing to synchronize with anything else.
The new fast path is implemented almost entirely in C in book3s_hv.c
and runs with the MMU on until the guest is entered. On guest exit
we use the existing path until the point where we are committed to
exiting the guest (as distinct from handling an interrupt in the
low-level code and returning to the guest) and we have pulled the
guest context from the XIVE. At that point we check a flag in the
stack frame to see whether we came in via the old path and the new
path; if we came in via the new path then we go back to C code to do
the rest of the process of saving the guest context and restoring the
host context.
The C code is split into separate functions for handling the
OS-accessible state and the hypervisor state, with the idea that the
latter can be replaced by a hypercall when we implement nested
virtualization.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix CONFIG_ALTIVEC=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not currently possible to create the full number of possible
VCPUs (KVM_MAX_VCPUS) on Power9 with KVM-HV when the guest uses fewer
threads per core than its core stride (or "VSMT mode"). This is
because the VCORE ID and XIVE offsets grow beyond KVM_MAX_VCPUS
even though the VCPU ID is less than KVM_MAX_VCPU_ID.
To address this, "pack" the VCORE ID and XIVE offsets by using
knowledge of the way the VCPU IDs will be used when there are fewer
guest threads per core than the core stride. The primary thread of
each core will always be used first. Then, if the guest uses more than
one thread per core, these secondary threads will sequentially follow
the primary in each core.
So, the only way an ID above KVM_MAX_VCPUS can be seen, is if the
VCPUs are being spaced apart, so at least half of each core is empty,
and IDs between KVM_MAX_VCPUS and (KVM_MAX_VCPUS * 2) can be mapped
into the second half of each core (4..7, in an 8-thread core).
Similarly, if IDs above KVM_MAX_VCPUS * 2 are seen, at least 3/4 of
each core is being left empty, and we can map down into the second and
third quarters of each core (2, 3 and 5, 6 in an 8-thread core).
Lastly, if IDs above KVM_MAX_VCPUS * 4 are seen, only the primary
threads are being used and 7/8 of the core is empty, allowing use of
the 1, 5, 3 and 7 thread slots.
(Strides less than 8 are handled similarly.)
This allows the VCORE ID or offset to be calculated quickly from the
VCPU ID or XIVE server numbers, without access to the VCPU structure.
[paulus@ozlabs.org - tidied up comment a little, changed some WARN_ONCE
to pr_devel, wrapped line, fixed id check.]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ARM:
- Include icache invalidation optimizations, improving VM startup time
- Support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- A small fix for power-management notifiers, and some cosmetic changes
PPC:
- Add MMIO emulation for vector loads and stores
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- Improve the handling of escalation interrupts with the XIVE interrupt
controller
- Support decrement register migration
- Various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- Exitless interrupts for emulated devices
- Cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- Hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- Paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- Allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512
features
- Show vcpu id in its anonymous inode name
- Many fixes and cleanups
- Per-VCPU MSR bitmaps (already merged through x86/pti branch)
- Stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJafvMtAAoJEED/6hsPKofo6YcH/Rzf2RmshrWaC3q82yfIV0Qz
Z8N8yJHSaSdc3Jo6cmiVj0zelwAxdQcyjwlT7vxt5SL2yML+/Q0st9Hc3EgGGXPm
Il99eJEl+2MYpZgYZqV8ff3mHS5s5Jms+7BITAeh6Rgt+DyNbykEAvzt+MCHK9cP
xtsIZQlvRF7HIrpOlaRzOPp3sK2/MDZJ1RBE7wYItK3CUAmsHim/LVYKzZkRTij3
/9b4LP1yMMbziG+Yxt1o682EwJB5YIat6fmDG9uFeEVI5rWWN7WFubqs8gCjYy/p
FX+BjpOdgTRnX+1m9GIj0Jlc/HKMXryDfSZS07Zy4FbGEwSiI5SfKECub4mDhuE=
=C/uD
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs
without requiring the complex thread synchronization that earlier
CPU versions required.
- A series from Ben Herrenschmidt to improve the handling of
escalation interrupts with the XIVE interrupt controller.
- Provide for the decrementer register to be copied across on
migration.
- Various minor cleanups and bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaYXViAAoJEJ2a6ncsY3GfDhgIAIDVBZH/Ftq7eJiUSxDpqyCQ
DF/x7fNKzK/J33pu+3ntOI2gZsldExAy7vH2M27I4qLIkbI5y3vu4v8l3CDlS1LK
9dKi72zg7baozoVF5mGUNm0B1sSvZiIQlC/kaami2aPTF1GcrJ561GthzfZwxENX
TSLqOA4LkeUZh2tUsvbcUrPi6v+E4Em2lgacQcx2ioMblWz56sZu79VsUbSSw/a3
P8+pIv7EbHw+TrOZMehjCbZkOdBeZ3IRLJsdlIAfe7y4vWME/5b9uVnQS/+XQj/B
6f3rQrduGvF2P6GMjsm8gDkgE5oZ1zbKlgO4i5WApnu80MMLFlfEUN+GWuGJ95Q=
=OjGs
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM update for 4.16
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs
without requiring the complex thread synchronization that earlier
CPU versions required.
- A series from Ben Herrenschmidt to improve the handling of
escalation interrupts with the XIVE interrupt controller.
- Provide for the decrementer register to be copied across on
migration.
- Various minor cleanups and bugfixes.
Pull asm/uaccess.h whack-a-mole from Al Viro:
"It's linux/uaccess.h, damnit... Oh, well - eventually they'll stop
cropping up..."
* 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
asm-prototypes.h: use linux/uaccess.h, not asm/uaccess.h
riscv: use linux/uaccess.h, not asm/uaccess.h...
ppc: for put_user() pull linux/uaccess.h, not asm/uaccess.h
This works on top of the single escalation support. When in single
escalation, with this change, we will keep the escalation interrupt
disabled unless the VCPU is in H_CEDE (idle). In any other case, we
know the VCPU will be rescheduled and thus there is no need to take
escalation interrupts in the host whenever a guest interrupt fires.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The prodded flag is only cleared at the beginning of H_CEDE,
so every time we have an escalation, we will cause the *next*
H_CEDE to return immediately.
Instead use a dedicated "irq_pending" flag to indicate that
a guest interrupt is pending for the VCPU. We don't reuse the
existing exception bitmap so as to avoid expensive atomic ops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
That feature, provided by Power9 DD2.0 and later, when supported
by newer OPAL versions, allows us to sacrifice a queue (priority 7)
in favor of merging all the escalation interrupts of the queues
of a single VP into a single interrupt.
This reduces the number of host interrupts used up by KVM guests
especially when those guests use multiple priorities.
It will also enable a future change to control the masking of the
escalation interrupts more precisely to avoid spurious ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add details about enabled queues and escalation interrupts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When we migrate a VM from a POWER8 host (XICS) to a POWER9 host
(XICS-on-XIVE), we have an error:
qemu-kvm: Unable to restore KVM interrupt controller state \
(0xff000000) for CPU 0: Invalid argument
This is because kvmppc_xics_set_icp() checks the new state
is internaly consistent, and especially:
...
1129 if (xisr == 0) {
1130 if (pending_pri != 0xff)
1131 return -EINVAL;
...
On the other side, kvmppc_xive_get_icp() doesn't set
neither the pending_pri value, nor the xisr value (set to 0)
(and kvmppc_xive_set_icp() ignores the pending_pri value)
As xisr is 0, pending_pri must be set to 0xff.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When restoring a pending interrupt, we are setting the Q bit to force
a retrigger in xive_finish_unmask(). But we also need to force an EOI
in this case to reach the same initial state : P=1, Q=0.
This can be done by not setting 'old_p' for pending interrupts which
will inform xive_finish_unmask() that an EOI needs to be sent.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In KVM's XICS-on-XIVE emulation, kvmppc_xive_get_xive() returns the
value of state->guest_server as "server". However, this value is not
set by it's counterpart kvmppc_xive_set_xive(). When the guest uses
this interface to migrate interrupts away from a CPU that is going
offline, it sees all interrupts as belonging to CPU 0, so they are
left assigned to (now) offline CPUs.
This patch removes the guest_server field from the state, and returns
act_server in it's place (that is, the CPU actually handling the
interrupt, which may differ from the one requested).
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The XIVE interrupt controller on POWER9 machines doesn't support byte
accesses to any register in the thread management area other than the
CPPR (current processor priority register). In particular, when
reading the PIPR (pending interrupt priority register), we need to
do a 32-bit or 64-bit load.
Cc: stable@vger.kernel.org # v4.13
Fixes: 2c4fb78f78 ("KVM: PPC: Book3S HV: Workaround POWER9 DD1.0 bug causing IPB bit loss")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The main thing here is a new implementation of the in-kernel
XICS interrupt controller emulation for POWER9 machines, from Ben
Herrenschmidt.
POWER9 has a new interrupt controller called XIVE (eXternal Interrupt
Virtualization Engine) which is able to deliver interrupts directly
to guest virtual CPUs in hardware without hypervisor intervention.
With this new code, the guest still sees the old XICS interface but
performance is better because the XICS emulation in the host uses the
XIVE directly rather than going through a XICS emulation in firmware.
Conflicts:
arch/powerpc/kernel/cpu_setup_power.S [cherry-picked fix]
arch/powerpc/kvm/book3s_xive.c [include asm/debugfs.h]
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
