IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Move IIO channel definitions in st_lsm6dsx_sensor_settings in order to
support sensors with different channels maps.
This is a preliminary patch to add support for LSM9DS1 sensor to
st_lsm6dsx driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove output register definition and inline register value since
they are used only for iio channel definition. This is a preliminary
patch to add support for LSM9DS1 sensor to st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move fs_table in st_lsm6dsx_sensor_settings in order to support
sensors with different gain maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move sensor odr table in st_lsm6dsx_sensor_settings in order to support
sensors with different odr maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a driver for the Maxim Integrated MAX5432-MAX5435 family of digital
potentiometers.
These potentiometers are connected via I2C and have 32 wiper
positions.
Supported functionality
- set the volatile wiper position
- read the potentiometer scale
Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX5432-MAX5435.pdf
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for register access was added for devices which have software
mode.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for ad7616 running in software was added. In order
to activate the software mode, HW_RNGSEL pins must be pulled low.
Oversampling and input ranges are now configured in corresponding
registers. Ad7616 has multiple scale options when it is configured
in software mode.
Also, in order to support multiple devices in software mode, the spi
calculation of registers address must be generic. Because
the length of address and bit which specifies the read/write operation is
different for every device, calculation of address was made generic.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to datasheet, ad7616 require at least 15ms after a restart
to fully reconfigure and being able to receive new commands via spi.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because software mode and register access are only available in spi, they
were moved in spi file and are accessbile via bops structure.
The write_os/scale will be overwritten by sw_mode_config function.
This patch was made in order to support devices in software mode without
making the driver dependent to spi and increase the abstraction of the
core.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The common channel definition which are going to be used by both core
file but also spi file, were moved in header file. Some devices have
different channel definitions when are used in software mode, feature
available only with spi, and those definitions will be added in spi file.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Embedded controller return minimum and maximum frequencies, unfortunately
we have no way to know the step for all available frequencies.
Even if not complete, we can return a list of known values using the
standard read_avail callback (IIO_CHAN_INFO_SAMP_FREQ) to provide them to
userland.
Now cros_ec_* sensors provides frequencies values in sysfs like this:
"0 min max". 0 is always true to disable the sensor.
Default frequencies are provided for earlier protocol.
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
[rebased on top of iio/testing and solved conflicts]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Veyron minnie embedded controller presents 2 accelerometers using an
older interface. Add function to query the data in cros_ec_accel.
Verify accelerometers on veyron-minnie are presented and working.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove duplicate code in cros-ec-accel-legacy,
use cros-ec-sensors-core functions and structures when possible.
On glimmer, check the 2 accelerometers are presented and working.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
INFO_SCALE is set both for each channel and all channels.
iio is using all channel setting, so the error was not user visible.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To allow cros_ec iio core library to be used with legacy device, add a
vector to rotate sensor data if necessary: legacy devices are not
reporting data in HTML5/Android sensor referential.
Check the data is not rotated on recent chromebooks that use the HTML5
standard to present sensor data.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a function to determine which version of the
protocol is used to communicate with EC.
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
[rebased on top of iio/testing and solved conflicts]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No need for using reverse logic in the irq return,
fix this by flip things around.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For today the st_lsm6dsx driver support LSM6DSO and LSM6DSR sensor only in
spi and i2c mode.
The LSM6DSO and LSM6DSR are also i3c capable so let's give i3c support to
them.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Everything is about mmc35240_ except MMC53240_WAIT_SET_RESET (3 and 5
switched).
This is likely a typo. Define and use MMC35240_WAIT_SET_RESET instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 device is a complete inertial system that includes a triaxial
gyroscope and a triaxial accelerometer. It's more simplified design than
that of the ADIS16480, and does not offer the triaxial magnetometers &
pressure sensors. It does also have a temperature sensor (like the
ADIS16480).
Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS
library.
Naturally, the register map is different and much more simplified than the
ADIS16480 subfamily, so it cannot be integrated into that driver. A major
difference is that the registers are not paged.
One thing that is particularly special about it, is that it requires a
higher delay between CS changes (i.e. when CS goes up, the spec recommends
that it be brought down after a minimum of 16 uS).
Other ADIS chips require (via spec) a minimum of 2 uS between CS changes.
The kernel's 10 uS default should be fine for those other chips; they
haven't been tested with lower CS change delays yet.
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 requires a higher delay before the next transfer. Since the
SPI framework supports configuring the delay before the next transfer, this
driver will become the first user of it.
The support for this functionality in ADIS16460 requires an addition to the
ADIS lib to support the `cs_change_delay` functionality from the SPI
subsystem.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove function is redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is meant to replace the i2c/spi transfer functions with
regmap. SPI framework requires DMA safe buffers so let's add GFP_DMA
flag for memory allocation used by bulk_read functions.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some devices need to be configured with special bit in order to
use spi 3-wire. This was done during device identification phase.
Instead, let's move this part as spi specific.
Doing this the check_device_support function becomes a simple
device id check, so let's rename it.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch set pressure settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch set magn settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch set gyro settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch set accel settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function is introduced to retrieve press device settings. It will be
used by probe in order to configure regmap.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function is introduced to retrieve magn device settings. It will be
used by probe in order to configure regmap.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function is introduced to retrieve gyro device settings. It will be
used by probe in order to configure regmap.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function is introduced to retrieve accel device settings. It will be
used by probe in order to configure regmap.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract from st_sensors_check_device_support() function the code that
is used to get the specific settings for a device. This will be used
as generic extractor by each ST driver.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Due to an API misread, error code can be different for -EIO when reading
a sysfs entry. Return the error reported by the cros_ec stack.
Check the proper error message (protocol error, not supported) is
reported when there is an error returned by the EC stack.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add calibration scale support to accel, gyro and magnetometer.
Check on eve with current firmware, check reading calibscale returns 1.0,
check with newer firmware values are applied.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
s/ADPS9960/APDS9960/
(P and D switched)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All #define are about SCA3000_... except the last one.
Make it consistent.
s/SAC3000/SCA3000/
This #define is apparently unused up to now.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Quadrature feature is now hosted on it own framework.
Remove quadrature related code from stm32-trigger driver to avoid
code duplication and simplify the ABI.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS3TR-C 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On stm32h7 and stm32mp1, the ADC inputs are multiplexed with analog
switches which have reduced performances when their supply is below 2.7V
(vdda by default):
- 3.3V embedded booster can be used, to get full ADC performances
(increases power consumption).
- vdd supply can be selected if above 2.7V by setting ANASWVDD syscfg bit,
on STM32MP1 only.
Make this optional, since this is a trade-off between analog performance
and power consumption.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for the stk33xx family of ambient light sensors.
Tested-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce local variable 'struct device *dev' and use it instead of
dereferencing it repeatly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
