IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently for each timestamp frame, the SW needs to go and read the
received timestamp over the MDIO bus. But the HW has the capability
to store the received nanoseconds part and the least significant two
bits of the seconds in the reserved field of the PTP header. In this
way we could save few MDIO transactions (actually a little more
transactions because the access to the PTP registers are indirect)
for each received frame.
Instead of reading the rest of seconds part of the timestamp of the
frame using MDIO transactions schedule PTP worker thread to read the
seconds part every 500ms and then for each of the received frames use
this information. Because if for example running with 512 frames per
second, there is no point to read 512 times the second part.
Doing all these changes will give a great CPU usage performance.
Running ptp4l with logSyncInterval of -9 will give a ~60% CPU
improvement.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.
This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.
The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of the file micrel.c there is list of supported PHYs.
Extend this list with the following PHYs lan8841, lan8814 and lan8804,
as these PHYs were added but the list was not updated.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230418124713.2221451-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the 1PPS output was enabled and then lan8841 was configured to be a
follower, then target clock which is used to generate the 1PPS was not
configure correctly. The problem was that for each adjustments of the
time, also the nanosecond part of the target clock was changed.
Therefore the initial nanosecond part of the target clock was changed.
The issue can be observed if both the leader and the follower are
generating 1PPS and see that their PPS are not aligned even if the time
is allined.
The fix consists of not modifying the nanosecond part of the target
clock when adjusting the time. In this way the 1PPS get also aligned.
Fixes: e4ed8ba08e3f ("net: phy: micrel: Add support for PTP_PF_PEROUT for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ9131RNX incorrectly shows EEE capabilities in its registers.
Although the "EEE control and capability 1" (Register 3.20) is set to 0,
indicating no EEE support, the "EEE advertisement 1" (Register 7.60) is
set to 0x6, advertising EEE support for 1000BaseT/Full and
100BaseT/Full.
This inconsistency causes PHYlib to assume there is no EEE support,
preventing control over EEE advertisement, which is enabled by default.
This patch resolves the issue by utilizing the ksz9477_get_features()
function to correctly set the EEE capabilities for the KSZ9131RNX. This
adjustment allows proper control over EEE advertisement and ensures
accurate representation of the device's capabilities.
Fixes: 8b68710a3121 ("net: phy: start using genphy_c45_ethtool_get/set_eee()")
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg
Where the configuration was the following:
[global]
ts2phc.pin_index 6
[eth2]
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'temp' was used before commit c0c99d0cd107 ("net: phy: micrel: remove
the use of .ack_interrupt()") refactored the code. Now, we can simplify
it a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230314124928.44948-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lan8841 has 10 GPIOs and it has 2 events(EVENT_A and EVENT_B). It is
possible to assigned the 2 events to any of the GPIOs, but a GPIO can
have only 1 event at a time.
These events are used to generate periodic signals. It is possible to
configure the length, the start time and the period of the signal by
configuring the event.
Currently the SW uses only EVENT_A to generate the perout.
These events are generated by comparing the target time with the PHC
time. In case the PHC time is changed to a value bigger than the target
time + reload time, then it would generate only 1 event and then it
would stop because target time + reload time is small than PHC time.
Therefore it is required to change also the target time every time when
the PHC is changed. The same will apply also when the PHC time is
changed to a smaller value.
This was tested using:
testptp -L 6,2
testptp -p 1000000000 -w 200000000
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230307214402.793057-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ8563R, which has same PHYID as KSZ9477 family, will change "EEE control
and capability 1" (Register 3.20) content depending on configuration of
"EEE advertisement 1" (Register 7.60). Changes on the 7.60 will affect
3.20 register.
So, instead of depending on register 3.20, driver should set supported_eee.
Proper supported_eee configuration is needed to make use of generic
PHY c45 set/get_eee functions provided by next patches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHC and timestamping operations for the lan8841 PHY.
PTP 1-step and 2-step modes are supported, over Ethernet and UDP both
ipv4 and ipv6.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cable diagnostics in lan8841 PHY. It has the same
registers layout as lan8814 PHY, therefore reuse the functionality.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230208114406.1666671-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) Ethernet physical layer transceivers for transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6,
unshielded twisted pair (UTP) cables.
The LAN8841 offers the industry-standard GMII/MII as well as the RGMII.
Some of the features of the PHY are:
- Wake on LAN
- Auto-MDIX
- IEEE 1588-2008 (V2)
- LinkMD Capable diagnosis
Currently the patch offers support only for link configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the NULL pointer case
Fixes New smatch warnings:
drivers/net/phy/micrel.c:2613 lan8814_ptp_probe_once() warn: passing zero to 'PTR_ERR'
vim +/PTR_ERR +2613 drivers/net/phy/micrel.c
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialized return variable
Fixes Old smatch warnings:
drivers/net/phy/micrel.c:1750 ksz886x_cable_test_get_status() error:
uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan8814 represents a package of 4 PHYs. All of them are sharing the
same interrupt line. So when a link was going down/up or a frame was
timestamped, then the interrupt handler of all the PHYs was called.
Which is all fine and expected but the problem is the way the handler
interrupt works.
Basically if one of the PHYs timestamp a frame, then all the other 3
PHYs were polling the status of the interrupt until that PHY actually
cleared the interrupt by reading the timestamp.
The reason of polling was in case another PHY was also timestamping a
frame at the same time, it could miss this interrupt. But this is not
the right approach, because it is the interrupt controller who needs to
call the interrupt handlers again if the interrupt line is still
active.
Therefore change this such when the interrupt handler is called check
only if the interrupt is for itself, otherwise just exit. In this way
save CPU usage.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230104194218.3785229-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for MDI-X status and configuration for KSZ9131 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FIELD_GET() must only be used with a mask that is a compile-time
constant. Mark the functions as __always_inline to avoid the problem.
Fixes: 21b688dabecb6a ("net: phy: micrel: Cable Diag feature for lan8814 phy")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Link: https://lore.kernel.org/r/20221011095437.12580-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Config_intr and handle_interrupt are enabled for ksz9477 phy. It is
similar to all other phys in the micrel phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inside the function lan8814_config_intr, there are double spaces when
assigning the return value of phy_write to err.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220921065444.637067-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ece19502834d ("net: phy: micrel: 1588 support for LAN8814
phy") the handler always returns IRQ_HANDLED, except in an error case.
Before that commit, the interrupt status register was checked and if
it was empty, IRQ_NONE was returned. Restore that behavior to play nice
with the interrupt line being shared with others.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <Divya.Koppera@microchip.com>
Link: https://lore.kernel.org/r/20220920141619.808117-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for interrupts for LAN8804 PHY.
Tested-by: Michael Walle <michael@walle.cc> # on kontron-kswitch-d10
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220913142926.816746-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LED support for extended mode where
LED 1: Enhanced Mode 5 (10M/1000M/Activity)
LED 2: Enhanced Mode 4 (100M/1000M/Activity)
By default it supports KSZ9031 LED mode
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that it is possible to use .probe without having .driver_data, let
KSZ8061 use the kszphy specific hooks for probe,suspend and resume,
which is preferred.
Switch to using the dedicated kszphy probe/suspend/resume functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.
Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lanphy_read_page_reg, calling __phy_read() might return a negative
error code. Use 'int' to check the error code.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220509144519.2343399-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the kszphy_suspend/
resume hooks are used.
These functions require the probe function to be called so that
priv can be allocated.
Otherwise, a NULL pointer dereference happens inside
kszphy_config_reset().
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the following
NULL pointer dereference is observed on a board with KSZ8061:
# udhcpc -i eth0
udhcpc: started, v1.35.0
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = f73cef4e
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94
Hardware name: Freescale i.MX6 SoloX (Device Tree)
PC is at kszphy_config_reset+0x10/0x114
LR is at kszphy_resume+0x24/0x64
...
The KSZ8061 phy_driver structure does not have the .probe/..driver_data
fields, which means that priv is not allocated.
This causes the NULL pointer dereference inside kszphy_config_reset().
Fix the problem by using the generic suspend/resume functions as before.
Another alternative would be to provide the .probe and .driver_data
information into the structure, but to be on the safe side, let's
just restore Ethernet functionality by using the generic suspend/resume.
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8814 has a coma mode pin which puts the PHY into isolate and
power-dowm mode. Unfortunately, the mode cannot be disabled by a
register. Usually, the input pin has a pull-up and connected to a GPIO
which can then be used to disable the mode. Try to get the GPIO and
deassert it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both lan8814_ptp_init() and lan8814_ptp_probe_once() are only used if
PTP and PHY timestamping is enabed. Up until now the probe function just
returns early, if they are not needed. But we need the
phy_package_init_once() functionality for the coma mode GPIO setup. Move
the check into the functions itself.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add cable test support for Micrel KSZ9x31 PHYs.
Tested on i.MX8M Mini with KSZ9131RNX in 100/Full mode with pairs shuffled
before magnetics:
(note: Cable test started/completed messages are omitted)
mx8mm-ksz9131-a-d-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code Short within Pair
Pair B, fault length: 0.80m
Pair C code Short within Pair
Pair C, fault length: 0.80m
Pair D code OK
mx8mm-ksz9131-a-b-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code OK
Pair C code Short within Pair
Pair C, fault length: 0.00m
Pair D code Short within Pair
Pair D, fault length: 0.00m
Tested on R8A77951 Salvator-XS with KSZ9031RNX and all four pairs connected:
(note: Cable test started/completed messages are omitted)
r8a7795-ksz9031-all-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code OK
Pair C code OK
Pair D code OK
The CTRL1000 CTL1000_ENABLE_MASTER and CTL1000_AS_MASTER bits are not
restored by calling phy_init_hw(), they must be manually cached in
ksz9x31_cable_test_start() and restored at the end of
ksz9x31_cable_test_get_status().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220407105534.85833-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the PHY and the MAC are capable of doing timestamping, the PHY has
priority. Therefore the DT option lan8814,ignore-ts was added such that
the PHY will not expose a PHC so then the timestamping was done in the
MAC. This is not the correct approach of doing it, therefore remove
this.
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the discussions here[1], the PHY driver is the wrong place
to set the latencies, therefore remove them.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan8814_match_rx_ts() invokes netif_rx() with disables interrupts
outside which will create a warning. Invoking netif_rx_ni() with
disabled interrupts is wrong even without the recent rework because
netif_rx_ni() would enable interrupts while processing the softirq. This
in turn can lead to dead lock if an interrupts triggers and attempts to
acquire kszphy_ptp_priv::rx_ts_lock.
Move netif_rx() outside the IRQ-off section.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic ptp_msg_is_sync() function to avoid code duplication.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 1588 in LAN8814 phy driver.
It supports 1-step and 2-step timestamping.
Co-developed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make Extended page register accessing atomic,
to overcome unexpected output from register
reads/writes.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for Link up or Link down
interrupt support in LAN8814 Quad phy
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211221112217.9502-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
