IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This was marked as unused in 5.19 and can now be removed
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During boot of I2SE Duckbill the kernel log contains a
confusing error:
Failed to request dma
This is caused by i2c-mxs tries to request a not yet available DMA
channel (-EPROBE_DEFER). So suppress this message by using
dev_err_probe().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add additional supported PCI IDs for latest AMD NAVI GPU card which
has an integrated Type-C controller and designware I2C with PCI
interface.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c_master_hub is only used in i2c-qcom-geni.c now,
change it to static.
Fixes: cacd9643eca7 ("i2c: qcom-geni: add support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure that i2c_mark_adapter_suspended() is always balanced by a call to
i2c_mark_adapter_resumed().
dw_i2c_plat_resume() must always be called, so that
i2c_mark_adapter_resumed() is called. This is not compatible with
DPM_FLAG_MAY_SKIP_RESUME, so remove the flag.
Since the controller is always resumed on system resume the
dw_i2c_plat_complete() callback is redundant and has been removed.
The unbalanced suspended flag was introduced by commit c57813b8b288
("i2c: designware: Lock the adapter while setting the suspended flag")
Before that commit, the system and runtime PM used the same functions. The
DPM_FLAG_MAY_SKIP_RESUME was used to skip the system resume if the driver
had been in runtime-suspend. If system resume was skipped, the suspended
flag would be cleared by the next runtime resume. The check of the
suspended flag was _after_ the call to pm_runtime_get_sync() in
i2c_dw_xfer(). So either a system resume or a runtime resume would clear
the flag before it was checked.
Having introduced the unbalanced suspended flag with that commit, a further
commit 80704a84a9f8
("i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers")
changed from using a local suspended flag to using the
i2c_mark_adapter_suspended/resumed() functions. These use a flag that is
checked by I2C core code before issuing the transfer to the bus driver, so
there was no opportunity for the bus driver to runtime resume itself before
the flag check.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: c57813b8b288 ("i2c: designware: Lock the adapter while setting the suspended flag")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow
by depending on the values of the given parameters including the ic_clk.
For example in our use case where ic_clk is larger than one million,
multiplication of ic_clk * 4700 will result in 32 bit overflow.
Add cast of u64 to the calculation to avoid multiplication overflow, and
use the corresponding define for divide.
Fixes: 2373f6b9744d ("i2c-designware: split of i2c-designware.c into core and bus specific parts")
Signed-off-by: Lareine Khawaly <lareine@amazon.com>
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make i2c_dw_clk_rate() to return u32 instead of unsigned long, as the
function return the value of get_clk_rate_khz() which returns u32.
Fixes: b33af11de236 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Many compatibles have been introduced, pointing to the same config data.
Leave a note reminding future developers to not do that again.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
bigger updates, the rest is driver updates all over the place
-----BEGIN PGP SIGNATURE-----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=/It5
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core got a new helper 'i2c_client_get_device_id()', designware got
some bigger updates, the rest is driver updates all over the place"
* tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (41 commits)
i2c: ismt: Fix an out-of-bounds bug in ismt_access()
i2c: mux: reg: check return value after calling platform_get_resource()
i2c: xiic: Make sure to disable clock on .remove()
i2c: hisi: Add support to get clock frequency from clock
i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
i2c: slave-eeprom: Convert to i2c's .probe_new()
i2c: mux: pca954x: Convert to i2c's .probe_new()
drivers/i2c: use simple i2c probe
i2c: mux: pca9541: switch to using .probe_new
i2c: gpio: Fix potential unused warning for 'i2c_gpio_dt_ids'
i2c: qcom-geni: add support for I2C Master Hub variant
i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant
soc: qcom: geni-se: add support for I2C Master Hub wrapper variant
soc: qcom: geni-se: add desc struct to specify clocks from device match data
dt-bindings: i2c: qcom-geni: document I2C Master Hub serial I2C engine
dt-bindings: qcom: geni-se: document I2C Master Hub wrapper variant
dt-bindings: i2c: renesas,riic: Document RZ/Five SoC
i2c: tegra: Set ACPI node as primary fwnode
i2c: smbus: add DDR support for SPD
i2c: /pasemi: PASemi I2C controller IRQ enablement
...
When the driver does not check the data from the user, the variable
'data->block[0]' may be very large to cause an out-of-bounds bug.
The following log can reveal it:
[ 33.995542] i2c i2c-1: ioctl, cmd=0x720, arg=0x7ffcb3dc3a20
[ 33.995978] ismt_smbus 0000:00:05.0: I2C_SMBUS_BLOCK_DATA: WRITE
[ 33.996475] ==================================================================
[ 33.996995] BUG: KASAN: out-of-bounds in ismt_access.cold+0x374/0x214b
[ 33.997473] Read of size 18446744073709551615 at addr ffff88810efcfdb1 by task ismt_poc/485
[ 33.999450] Call Trace:
[ 34.001849] memcpy+0x20/0x60
[ 34.002077] ismt_access.cold+0x374/0x214b
[ 34.003382] __i2c_smbus_xfer+0x44f/0xfb0
[ 34.004007] i2c_smbus_xfer+0x10a/0x390
[ 34.004291] i2cdev_ioctl_smbus+0x2c8/0x710
[ 34.005196] i2cdev_ioctl+0x5ec/0x74c
Fix this bug by checking the size of 'data->block[0]' first.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If for whatever reasons pm_runtime_resume_and_get() failed, .remove() is
exited early, the clock isn't freed and runtime PM state isn't reset.
The right thing to do however is to free all resources that don't need
HW access after a problem with runtime PM. Also issue a warning in that
case and return 0 to suppress a less helpful warning by the driver core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The clk_rate attribute is not generic device tree bindings for I2C
busses described in Documentation/devicetree/bindings/i2c/i2c.txt.
It can be managed by clock binding.
Support the driver to obtain clock information by clk_rate or
clock property. Find clock first, if not, fall back to clk_rate.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using pcim_enable_device() to avoid missing pci_disable_device().
Fixes: 7e94dd154e93 ("i2c-pxa2xx: Add PCI support for PXA I2C controller")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Dropping a matching #ifdef check along with dropping of_match_ptr()
is just a cleanup, while dropping of_match_ptr() that has no
corresponding #ifdef fixes an actual warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.
Add the I2C Master Hub serial engine compatible along the specific
requirements in a new desc struct passed through the device match data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.
Those I2C serial engines variants have some requirements:
- a separate "core" clock
- doesn't support DMA, thus no memory interconnect path
- fixed FIFO size not discoverable in the HW_PARAM_0 register
Add a desc struct specifying all those requirements which will be used in
a next change when adding the I2C Master Hub serial engine compatible.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e70 ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Set ACPI node as the primary fwnode of I2C adapter to allow
enumeration of child devices from the ACPI table
Signed-off-by: Zubair Waheed <zwaheed@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix to return a negative error code from the gi2c->err instead of
0.
Fixes: d8703554f4de ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasoluitons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit "i2c: cadence: Add standard bus recovery support" breaks for i2c
devices that have no pinctrl defined. There is no requirement for this
to exist in the DT. This has worked perfectly well without this before in
at least 1 real usage case on hardware (Mali Komeda DPU, Cadence i2c to
talk to a tda99xx phy). Adding the requirement to have pinctrl set up in
the device tree (or otherwise be found) is a regression where the whole
i2c device is lost entirely (in this case dropping entire devices which
then leads to the drm display stack unable to find the phy for display
output, thus having no drm display device and so on down the chain).
This converts the above commit to an enhancement if pinctrl can be found
for the i2c device, providing a timeout on read with recovery, but if not,
do what used to be done rather than a fatal loss of a device.
This restores the mentioned display devices to their working state again.
Fixes: 58b924241d0a ("i2c: cadence: Add standard bus recovery support")
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
[wsa: added braces to else-branch]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds IRQ support to the PASemi I2C controller driver to
increase the performace of I2C transactions on platforms with PASemi I2C
controllers. While primarily intended for Apple silicon platforms, this
patch should also help in enabling IRQ support for older PASemi hardware
as well should the need arise.
This version of the patch has been tested on an M1 Ultra Mac Studio,
as well as an M1 MacBook Pro, and userspace launches successfully
while using the IRQ path for I2C transactions.
Signed-off-by: Arminder Singh <arminders208@outlook.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
npcm_i2c_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DW_IC_COMP_VERSION register contains the ASCII representation of the
Synopsys component version. Here 0x3131312A == "111*" means version
1.11* required for DW_IC_SDA_HOLD register availability where '*' means
any letter starting from 'a'.
DW_IC_COMP_TYPE is constant and is derived from two ASCII letters "DW"
followed by a 16-bit unsigned number.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Align all defines to the same column.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 90312351fd1e ("i2c: designware: MASTER mode as separated driver")
introduced disable_int pointer but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable_int() and scope is inside the same kernel module.
Since i2c_dw_disable_int() is just masking interrupts and the direct
DW_IC_INTR_MASK register write looks more clear in the code use that and
remove it from common code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In my opinion a few lines of spurious interrupt detection code can be
moved to the actual master interrupt handling function i2c_dw_isr()
without hurting readability.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It is kind of needless to print interrupt status when code immediately
after that finds interrupt was not originating from this device.
Therefore move it after spurious interrupt detection.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Do not return with interrupt handled if host controller is off and thus
interrupt is originating from other device or is spurious.
Add a check to detect when controller is runtime suspended or
transitioning/reset. In latter case all raw interrupt status register
bits may read one. In both cases return IRQ_NONE to indicate interrupt
was not from this device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Interrupt processing code in i2c-designware-slave.c is bit more readable
if not divided into another subroutine. Also explicit IRQ_NONE and
IRQ_HANDLED return values are more obvious.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unused completion code from i2c-designware-slave.c. Used only in
i2c-designware-master.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
These struct dw_i2c_dev members are not used in i2c-designware-slave.c
so remove re-initialization of them from i2c_dw_reg_slave().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Define software status flags with a BIT() macro. While at it remove
STATUS_IDLE and replace its use with zero initialization and status
flags clearing with a mask.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Writes from I2C bus often fail when testing the i2c-designware-slave.c
with the slave-eeprom backend. The same writes work correctly when
testing with a real 24c02 EEPROM chip.
In the tests below an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6.
1. i2cset -y 6 0x65 0x00 0x55
Single byte 0x55 write into address 0x00. No data goes into simulated
EEPROM. Debug prints from the i2c_dw_irq_handler_slave():
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
2. i2ctransfer -y 6 w9@0x65 0x00 0xff-
Write 8 bytes with decrementing value starting from 0xff at address 0x00
and forward. Only some of the data goes into arbitrary addresses.
Content is something like below but varies:
00000000 f9 f8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000050 00 00 00 00 00 00 ff fe 00 00 00 00 00 00 00 00 |................|
000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fb fa |................|
In this case debug prints were:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x510 : INTR_STAT=0x0
Both cases show there is more data coming from the receive FIFO still
after detecting the STOP condition. This can be seen from interrupt
status bits DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4).
Perhaps due interrupt latencies the receive FIFO is not read fast
enough, STOP detection happens synchronously when it occurs on the I2C
bus and the DW_IC_INTR_RX_FULL keeps coming as long as there are more
bytes in the receive FIFO.
Fix this by reading the receive FIFO completely empty whenever
DW_IC_INTR_RX_FULL occurs. Use RFNE, Receive FIFO Not Empty bit in the
DW_IC_STATUS register to loop through bytes in the FIFO.
While at it do not test the return code from i2c_slave_event() for the
I2C_SLAVE_WRITE_RECEIVED since to my understanding this hardware cannot
generate NACK to incoming bytes and debug print itself does not have
much value.
Reported-by: Tian Ye <tianye@sugon.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some read types from I2C bus don't work correctly when testing the
i2c-designware-slave.c with the slave-eeprom backend. The same reads
work correctly when testing with a real 24c02 EEPROM chip.
In the following tests an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6:
1. i2cdump -y 6 0x65 b (OK)
Random read. Each byte are read using a byte address write with a
current address read in a same message.
2. i2cdump -y 6 0x65 c (OK, was NOK before commit 3b5f7f10ff6e when it
was repeating the 1st byte)
Repeated current address read. One byte address write message
followed by repeated current address read messages.
3. i2cdump -y 6 0x65 i (NOK, each 32 byte block repeats the 1st byte of
block)
Sequential read using SMBus Block Read. For each 32 byte block a byte
address write followed by 32 sequental reads in a same message.
These findings are explained because the implementation has had a
mismatch between hardware interrupts and what I2C slave events should be
sent after those interrupts. Despite that the case 1 happened to have
always the I2C slave events sent to a right order with a right data
between backend and the I2C bus.
Hardware generates the DW_IC_INTR_RD_REQ interrupt when another host is
attempting to read and for sequential reads after. DW_IC_INTR_RX_DONE
occurs when host does not acknowledge a transmitted byte which is an
indication the end of transmission.
Those interrupts do not match directly with I2C_SLAVE_READ_REQUESTED and
I2C_SLAVE_READ_PROCESSED events which is how the code was and is
practically using them. The slave-eeprom backend increases the buffer
index with the I2C_SLAVE_READ_PROCESSED event and returns the data from
current index when receiving only the I2C_SLAVE_READ_REQUESTED event.
That explains the repeated bytes in case 3 and also case 2 before
commit 3b5f7f10ff6e ("i2c: designware: slave should do WRITE_REQUESTED
before WRITE_RECEIVED").
Patch fixes the case 3 while keep cases 1 and 2 working with following
changes:
- First DW_IC_INTR_RD_REQ interrupt will change the state machine to
read in progress state, send I2C_SLAVE_READ_REQUESTED event and
transmit the first byte from backend
- Subsequent DW_IC_INTR_RD_REQ interrupts will send
I2C_SLAVE_READ_PROCESSED events and transmit next bytes from backend
- STOP won't change the state machine. Otherwise case 2 won't work since
we cannot distinguish current address read from sequentiel read
- DW_IC_INTR_RX_DONE interrupt is needless since there is no mechanism
to inform it to a backend. It cannot be used to change state machine
at the end of read either due the same reason than above
- Next host write to us will change the state machine from read to write
in progress state
- STATUS_WRITE_IN_PROGRESS and STATUS_READ_IN_PROGRESS are considered
now to be status flags not the state of the driver. This is how we
treat them in i2c-designware-master.c
While at it do not test the return code from i2c_slave_event() for
I2C_SLAVE_READ_REQUESTED and I2C_SLAVE_READ_PROCESSED since it returns
always 0.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The HiSilicon I2C controller can be used on embedded platform, which
boot from devicetree.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To make the code easier to understand, add longer names to the
definitions of register fields. These longer names are based on source
code published by DELL/AESS for WPCM450, but should apply just as well
to NPCM7xx and NPCM8xx.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The unlabelled registers NPCM_I2CCTL4 to NPCM_I2CSCLHT overlap with the
bank 1 registers below, and they are accessed after selecting bank 0, so
they clearly belong to bank 0.
Move them together with the other bank 0 registers, and move the
unrelated definition of npcm_i2caddr down to keep the banked registers
in one piece.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c support for MT7986 SoC.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use msix or msi interrupts if the hardware supports it. Else, fallback to
legacy interrupts.
Co-developed-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the I2C controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the I2C controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
This fixes an issue where the DMA engine's SMMU stream ID needs to be
misleadingly set for the I2C controllers in device tree.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In piix4_probe(), the piix4 adapter will be registered in:
piix4_probe()
piix4_add_adapters_sb800() / piix4_add_adapter()
i2c_add_adapter()
Based on the probed device type, piix4_add_adapters_sb800() or single
piix4_add_adapter() will be called.
For the former case, piix4_adapter_count is set as the number of adapters,
while for antoher case it is not set and kept default *zero*.
When piix4 is removed, piix4_remove() removes the adapters added in
piix4_probe(), basing on the piix4_adapter_count value.
Because the count is zero for the single adapter case, the adapter won't
be removed and makes the sources allocated for adapter leaked, such as
the i2c client and device.
These sources can still be accessed by i2c or bus and cause problems.
An easily reproduced case is that if a new adapter is registered, i2c
will get the leaked adapter and try to call smbus_algorithm, which was
already freed:
Triggered by: rmmod i2c_piix4 && modprobe max31730
BUG: unable to handle page fault for address: ffffffffc053d860
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 3752 Comm: modprobe Tainted: G
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:i2c_default_probe (drivers/i2c/i2c-core-base.c:2259) i2c_core
RSP: 0018:ffff888107477710 EFLAGS: 00000246
...
<TASK>
i2c_detect (drivers/i2c/i2c-core-base.c:2302) i2c_core
__process_new_driver (drivers/i2c/i2c-core-base.c:1336) i2c_core
bus_for_each_dev (drivers/base/bus.c:301)
i2c_for_each_dev (drivers/i2c/i2c-core-base.c:1823) i2c_core
i2c_register_driver (drivers/i2c/i2c-core-base.c:1861) i2c_core
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
</TASK>
---[ end trace 0000000000000000 ]---
Fix this problem by correctly set piix4_adapter_count as 1 for the
single adapter so it can be normally removed.
Fixes: 528d53a1592b ("i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This fixes maybe_unused warnings/errors.
According to a comment during device tree removal, only ACPI is supported,
thus let's actually require it.
Fixes: be18c5ede25d ("i2c: mlxbf: remove device tree support")
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for sis630
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When we compile-in the CCI along with the imx412 driver and run on the RB5
we see that i2c_add_adapter() causes the probe of the imx412 driver to
happen.
This probe tries to perform an i2c xfer() and the xfer() in i2c-qcom-cci.c
fails on pm_runtime_get() because the i2c-qcom-cci.c::probe() function has
not completed to pm_runtime_enable(dev).
Fix this sequence by ensuring pm_runtime_xxx() calls happen prior to adding
the i2c adapter.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The missing "platform" alias is required for the mgb4 v4l2 driver to load
the i2c controller driver when probing the HW.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- add a new SoC to the qcom-cci driver
- fix an issue with the designware driver which now got enough testing
- the aspeed driver handles now busy target backends better
-----BEGIN PGP SIGNATURE-----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=zzCf
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1-batch2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- correct a variable type in the new pci1xxxx driver
- add a new SoC to the qcom-cci driver
- fix an issue with the designware driver which now got enough testing
- the aspeed driver now handles busy target backends better
* tag 'i2c-for-6.1-rc1-batch2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: aspeed: Assert NAK when slave is busy
i2c: designware: Fix handling of real but unexpected device interrupts
i2c: qcom-cci: Add MSM8226 compatible
dt-bindings: i2c: qcom,i2c-cci: Document clocks for MSM8974
dt-bindings: i2c: qcom,i2c-cci: Document MSM8226 compatible
i2c: microchip: pci1xxxx: Fix comparison of -EPERM against an unsigned variable
