IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 4e0effd900 ]
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d184c83f ]
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b5d73fb86 upstream.
Enables PCIe PTM (Precision Time Measurement) support in the igc
driver. Notifies the PCI devices that PCIe PTM should be enabled.
PCIe PTM is similar protocol to PTP (Precision Time Protocol) running
in the PCIe fabric, it allows devices to report time measurements from
their internal clocks and the correlation with the PCIe root clock.
The i225 NIC exposes some registers that expose those time
measurements, those registers will be used, in later patches, to
implement the PTP_SYS_OFFSET_PRECISE ioctl().
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd5855e6b1 ]
After PF reset and ethtool -t there was call trace in dmesg
sometimes leading to panic. When there was some time, around 5
seconds, between reset and test there were no errors.
Problem was that pf reset calls i40e_vsi_close in prep_for_reset
and ethtool -t calls i40e_vsi_close in diag_test. If there was not
enough time between those commands the second i40e_vsi_close starts
before previous i40e_vsi_close was done which leads to crash.
Add check to diag_test if pf is in reset and don't start offline
tests if it is true.
Add netif_info("testing failed") into unhappy path of i40e_diag_test()
Fixes: e17bc411ae ("i40e: Disable offline diagnostics if VFs are enabled")
Fixes: 510efb2682 ("i40e: Fix ethtool offline diagnostic with netqueues")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb050670a ]
If ADQ is enabled for a VF, then actual number of queue pair
is a number of currently available traffic classes for this VF.
Without this change the configuration of the Rx/Tx queues
fails with error.
Fixes: d29e0d233e ("i40e: missing input validation on VF message handling by the PF")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3238d36c3 ]
Procedure of configure tc flower filters erroneously allows to create
filters on TC0 where unfiltered packets are also directed by default.
Issue was caused by insufficient checks of hw_tc parameter specifying
the hardware traffic class to pass matching packets to.
Fix checking hw_tc parameter which blocks creation of filters on TC0.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7bb0fb7c63 upstream.
When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE
bit (VLAN Promiscuous Enable) is set. This means that the VF will
receive packets whose VLAN is not the same than the VLAN of the VF.
For instance, in this situation:
┌────────┐ ┌────────┐ ┌────────┐
│ │ │ │ │ │
│ │ │ │ │ │
│ VF0├────┤VF1 VF2├────┤VF3 │
│ │ │ │ │ │
└────────┘ └────────┘ └────────┘
VM1 VM2 VM3
vf 0: vlan 1000
vf 1: vlan 1000
vf 2: vlan 1001
vf 3: vlan 1001
If we tcpdump on VF3, we see all the packets, even those transmitted
on vlan 1000.
This behavior prevents to bridge VF1 and VF2 in VM2, because it will
create a loop: packets transmitted on VF1 will be received by VF2 and
vice-versa, and bridged again through the software bridge.
This patch remove the activation of VLAN Promiscuous when a VF enables
the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast
Promiscuous) is kept, so that a VF receives all packets that has the
same VLAN, whatever the destination MAC address.
Fixes: 8443c1a4b1 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 803e9895ea upstream.
After a VF requested to remove the promiscuous flag on an interface, the
broadcast packets are not received anymore. This breaks some protocols
like ARP.
In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM
bit (Broadcast Accept) on promiscuous removal.
This flag is already set by default in ixgbe_set_vmolr() on VF reset.
Fixes: 8443c1a4b1 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 942d2ad5d2 ]
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31b6298fd8 ]
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f95a7472d upstream.
The bug is here:
ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err);
The list iterator 'ch' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, use a new variable 'iter' as the list iterator,
while use the origin variable 'ch' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org
Fixes: 1d8d80b4e4 ("i40e: Add macvlan support on i40e")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04ebaa1cfd upstream.
When we decode the latency and the max_latency, u16 value may not fit
the required size and could lead to the wrong LTR representation.
Scaling is represented as:
scale 0 - 1 (2^(5*0)) = 2^0
scale 1 - 32 (2^(5 *1))= 2^5
scale 2 - 1024 (2^(5 *2)) =2^10
scale 3 - 32768 (2^(5 *3)) =2^15
scale 4 - 1048576 (2^(5 *4)) = 2^20
scale 5 - 33554432 (2^(5 *4)) = 2^25
scale 4 and scale 5 required 20 and 25 bits respectively.
scale 6 reserved.
Replace the u16 type with the u32 type and allow corrected LTR
representation.
Cc: stable@vger.kernel.org
Fixes: 44a13a5d99 ("e1000e: Fix the max snoop/no-snoop latency for 10M")
Reported-by: James Hutchinson <jahutchinson99@googlemail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 907862e9ae ]
An infinite loop may occur if we fail to acquire the HW semaphore,
which is needed for resource release.
This will typically happen if the hardware is surprise-removed.
At this stage there is nothing to do, except log an error and quit.
Fixes: c0071c7aa5 ("igc: Add HW initialization code")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9124c68f0 ]
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be7 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ef6813b2 ]
Disable check for queue being enabled in ice_vc_dis_qs_msg, because
there could be a case when queues were created, but were not enabled.
We still need to delete those queues.
Normal workflow for VF looks like:
Enable path:
VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10)
VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6)
VIRTCHNL_OP_ENABLE_QUEUES (opcode 8)
Disable path:
VIRTCHNL_OP_DISABLE_QUEUES (opcode 9)
VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11)
The issue appears only in stress conditions when VF is enabled and
disabled very fast.
Eventually there will be a case, when queues are created by
VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by
VIRTCHNL_OP_ENABLE_QUEUES.
In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES,
because there is a check whether queues are enabled in
ice_vc_dis_qs_msg.
When we bring up the VF again, we will see the "Failed to set LAN Tx queue
context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This
happens because old 16 queues were not deleted and VF requests to create
16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to
find a parent node for first newly requested queue (because all nodes
are allocated to 16 old queues).
Testing Hints:
Just enable and disable VF fast enough, so it would be disabled before
reaching VIRTCHNL_OP_ENABLE_QUEUES.
while true; do
ip link set dev ens785f0v0 up
sleep 0.065 # adjust delay value for you machine
ip link set dev ens785f0v0 down
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccfee18220 ]
When VF is freshly created, but not brought up, ring->txq_teid
value is by default set to 0.
But 0 is a valid TEID. On some platforms the Root Node of
Tx scheduler has a TEID = 0. This can cause issues as shown below.
The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF).
Testing Hints:
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
ip link set dev ens785f0v0 up
ip link set dev ens785f0v0 down
If we have freshly created VF and quickly turn it on and off, so there
would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then
VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error:
[ 639.531454] disable queue 89 failed 14
[ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR
[ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5
The reason for the fail is that we are trying to send AQ command to
delete queue 89, which has never been created and receive an "invalid
argument" error from firmware.
As this queue has never been created, it's teid and ring->txq_teid
have default value 0.
ice_dis_vsi_txq has a check against non-existent queues:
node = ice_sched_find_node_by_teid(pi->root, q_teids[i]);
if (!node)
continue;
But on some platforms the Root Node of Tx scheduler has a teid = 0.
Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is
pi->root), and we go further to submit an erroneous request to firmware.
Fixes: 37bb839012 ("ice: Move common functions out of ice_main.c part 7/7")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd8c624c0c ]
VSI is set as default forwarding one when promisc mode is set for
PF interface, when PF is switched to switchdev mode or when VF
driver asks to enable allmulticast or promisc mode for the VF
interface (when vf-true-promisc-support priv flag is off).
The third case is buggy because in that case VSI associated with
VF remains as default one after VF removal.
Reproducer:
1. Create VF
echo 1 > sys/class/net/ens7f0/device/sriov_numvfs
2. Enable allmulticast or promisc mode on VF
ip link set ens7f0v0 allmulticast on
ip link set ens7f0v0 promisc on
3. Delete VF
echo 0 > sys/class/net/ens7f0/device/sriov_numvfs
4. Try to enable promisc mode on PF
ip link set ens7f0 promisc on
Although it looks that promisc mode on PF is enabled the opposite
is true because ice_vsi_sync_fltr() responsible for IFF_PROMISC
handling first checks if any other VSI is set as default forwarding
one and if so the function does not do anything. At this point
it is not possible to enable promisc mode on PF without re-probe
device.
To resolve the issue this patch clear default forwarding VSI
during ice_vsi_release() when the VSI to be released is the default
one.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dba29537c ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc97f9c6f9 ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad35ffa252 ]
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6730a871e ]
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79498d5af8 ]
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6b ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5710ab7916 ]
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6b ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45eebd6299 ]
Replace state changes of iavf state machine
with a method that also tracks the previous
state the machine was on.
This change is required for further work with
refactoring init and watchdog state machines.
Tracking of previous state would help us
recover iavf after failure has occurred.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4208653a3 upstream.
Similar to "igc_read_phy_reg_gpy: drop premature return" patch.
igc_write_phy_reg_gpy checks the return value from igc_write_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fda2635466 upstream.
igc_read_phy_reg_gpy checks the return value from igc_read_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c7273a266 upstream.
Commit c685c69fba ("ixgbe: don't do any AF_XDP zero-copy transmit if
netif is not OK") addressed the ring transient state when
MEM_TYPE_XSK_BUFF_POOL was being configured which in turn caused the
interface to through down/up. Maurice reported that when carrier is not
ok and xsk_pool is present on ring pair, ksoftirqd will consume 100% CPU
cycles due to the constant NAPI rescheduling as ixgbe_poll() states that
there is still some work to be done.
To fix this, do not set work_done to false for a !netif_carrier_ok().
Fixes: c685c69fba ("ixgbe: don't do any AF_XDP zero-copy transmit if netif is not OK")
Reported-by: Maurice Baijens <maurice.baijens@ellips.com>
Tested-by: Maurice Baijens <maurice.baijens@ellips.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fadead80fe upstream.
Commit c503e63200 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6ba5273d4 upstream.
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 46b699c50c ]
The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.
This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).
With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe68195daf ]
From 4.17 onwards the ixgbevf driver uses build_skb() to build an skb
around new data in the page buffer shared with the ixgbe PF.
This uses either a 2K or 3K buffer, and offsets the DMA mapping by
NET_SKB_PAD + NET_IP_ALIGN. When using a smaller buffer RXDCTL is set to
ensure the PF does not write a full 2K bytes into the buffer, which is
actually 2K minus the offset.
However on the 82599 virtual function, the RXDCTL mechanism is not
available. The driver attempts to work around this by using the SET_LPE
mailbox method to lower the maximm frame size, but the ixgbe PF driver
ignores this in order to keep the PF and all VFs in sync[0].
This means the PF will write up to the full 2K set in SRRCTL, causing it
to write NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the buffer.
With 4K pages split into two buffers, this means it either writes
NET_SKB_PAD + NET_IP_ALIGN bytes past the first buffer (and into the
second), or NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the DMA
mapping.
Avoid this by only enabling build_skb when using "large" buffers (3K).
These are placed in each half of an order-1 page, preventing the PF from
writing past the end of the mapping.
[0]: Technically it only ever raises the max frame size, see
ixgbe_set_vf_lpe() in ixgbe_sriov.c
Fixes: f15c5ba5b6 ("ixgbevf: add support for using order 1 pages to receive large frames")
Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b8428b845 upstream.
Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.
Update debugfs code to use the correct format specifier for u64.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f344c8129 upstream.
Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92947844b8 upstream.
When XDP was configured on a system with large number of CPUs
and X722 NIC there was a call trace with NULL pointer dereference.
i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12
i40e 0000:87:00.0: setup of MAIN VSI failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e]
Call Trace:
? i40e_reconfig_rss_queues+0x130/0x130 [i40e]
dev_xdp_install+0x61/0xe0
dev_xdp_attach+0x18a/0x4c0
dev_change_xdp_fd+0x1e6/0x220
do_setlink+0x616/0x1030
? ahci_port_stop+0x80/0x80
? ata_qc_issue+0x107/0x1e0
? lock_timer_base+0x61/0x80
? __mod_timer+0x202/0x380
rtnl_setlink+0xe5/0x170
? bpf_lsm_binder_transaction+0x10/0x10
? security_capable+0x36/0x50
rtnetlink_rcv_msg+0x121/0x350
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x50/0xf0
netlink_unicast+0x1d3/0x2a0
netlink_sendmsg+0x22a/0x440
sock_sendmsg+0x5e/0x60
__sys_sendto+0xf0/0x160
? __sys_getsockname+0x7e/0xc0
? _copy_from_user+0x3c/0x80
? __sys_setsockopt+0xc8/0x1a0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f83fa7a39e0
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f ("i40e: main driver core")
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d701658a50 upstream.
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf329 ("i40e: driver core headers")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b13bd5313 upstream.
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e ("i40e: Add delay after EMP reset for firmware to recover")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e738451d78 upstream.
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40feded8a2 upstream.
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb5 ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
