IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Implement ->set_msix() and ->get_msix() callback functions in order
to configure MSIX capability in the PCIe endpoint controller.
Add cdns_pcie_ep_send_msix_irq() to send MSIX interrupts to Host.
cdns_pcie_ep_send_msix_irq() gets the MSIX table address (virtual
address) from "struct cdns_pcie_epf" that gets initialized in
->set_bar() call back function.
[kishon@ti.com: Re-implement MSIX support in accordance with the
re-designed core MSI-X interfaces]
Link: https://lore.kernel.org/r/20200722110317.4744-11-kishon@ti.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
sparse report build warning as follows:
drivers/pci/controller/pci-hyperv.c:941:5: warning:
symbol 'hv_read_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1021:5: warning:
symbol 'hv_write_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1090:5: warning:
symbol 'hv_register_block_invalidate' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Link: https://lore.kernel.org/r/20200706135234.80758-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe
controller") in order to update Vendor ID, directly wrote to
PCI_VENDOR_ID register. However PCI_VENDOR_ID in root port configuration
space is read-only register and writing to it will have no effect.
Use local management register to configure Vendor ID and Subsystem Vendor
ID.
Link: https://lore.kernel.org/r/20200722110317.4744-10-kishon@ti.com
Fixes: 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe controller")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence driver uses "mem" memory resource to obtain the offset of
configuration space address region, memory space address region and
message space address region. The obtained offset is used to program
the Address Translation Unit (ATU). However certain platforms like TI's
J721E SoC require the absolute address to be programmed in the ATU and
not just the offset. Add new *ops* for CPU addr fixup for the platform
drivers to provide the correct address to be programmed in the ATU.
Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's J721E allows only 32-bit configuration
space access. In such cases pci_generic_config_read and
pci_generic_config_write cannot be used. Add support in Cadence core
to let pci_host_bridge have custom pci_ops.
Link: https://lore.kernel.org/r/20200722110317.4744-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add cdns_pcie_ops to start link and verify link status. The registers
to start link and to check link status is in Platform specific PCIe
wrapper. Add support for platform specific drivers to add callback
functions for the PCIe Cadence core to start link and verify link status.
Link: https://lore.kernel.org/r/20200722110317.4744-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Certain platforms like TI's J721E using Cadence PCIe IP can perform only
32-bit accesses for reading or writing to Cadence registers. Convert all
read and write accesses to 32-bit in Cadence PCIe driver in preparation
for adding PCIe support in TI's J721E SoC.
Also add spin lock to disable interrupts while modifying PCI_STATUS
register while raising legacy interrupt since PCI_STATUS is accessible
by both remote RC and EP and time between read and write should be
minimized.
Link: https://lore.kernel.org/r/20200722110317.4744-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit bd22885aa1 ("PCI: cadence: Refactor driver to use as a core
library") while refactoring the Cadence PCIe driver to be used as
library, removed pm_runtime_get_sync() from cdns_pcie_ep_setup()
and cdns_pcie_host_setup() but missed to remove the corresponding
pm_runtime_put_sync() in the error path. Fix it here.
Link: https://lore.kernel.org/r/20200722110317.4744-3-kishon@ti.com
Fixes: bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
property to configure the number of bits passed through from PCIe
address to internal address in Inbound Address Translation register.
This only used the NO MATCH BAR.
However standard PCI dt-binding already defines "dma-ranges" to
describe the address ranges accessible by PCIe controller. Add support
in Cadence PCIe host driver to parse dma-ranges and configure the
inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB.
This adds support to take the next biggest region in "dma-ranges" and
find the smallest BAR that each of the regions fit in and if there is
no BAR big enough to hold the region, split the region to see if it can
be fitted using multiple BARs.
"dma-ranges" of J721E will be
dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
Since there is no BAR which can hold 2^48 size, NO_MATCH_BAR will be
used here.
Legacy device tree binding compatibility is maintained by retaining
support for "cdns,no-bar-match-nbits".
Link: https://lore.kernel.org/r/20200722110317.4744-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Kdump could fail sometime on Hyper-V guest because the retry in
hv_pci_enter_d0() releases child device structures in hv_pci_bus_exit().
Although there is a second asynchronous device relations message sending
from the host, if this message arrives to the guest after
hv_send_resource_allocated() is called, the retry would fail.
Fix the problem by moving retry to hv_pci_probe() and start the retry
from hv_pci_query_relations() call. This will cause a device relations
message to arrive to the guest synchronously; the guest would then be
able to rebuild the child device structures before calling
hv_send_resource_allocated().
Link: https://lore.kernel.org/r/20200727071731.18516-1-weh@microsoft.com
Fixes: c81992e7f4 ("PCI: hv: Retry PCI bus D0 entry on invalid device state")
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: fixed a comment and commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the datasheet of Loongson LS7A bridge chip, the old version
of Loongson LS7A PCIE port has a wrong value about PCI class which is
0x060000, the correct value should be 0x060400, this bug can be fixed by
"dev->class = PCI_CLASS_BRIDGE_PCI << 8;" at the software level and it
was fixed in hardware in the latest LS7A versions.
In order to maintain downward compatibility, use DECLARE_PCI_FIXUP_EARLY
instead of DECLARE_PCI_FIXUP_HEADER for bridge_class_quirk() to fix it as
early as possible.
Otherwise, in the function pci_setup_device(), the related code about
"dev->class" such as "class = dev->class >> 8;" and "dev->transparent
= ((dev->class & 0xff) == 1);" maybe get wrong value without EARLY fixup.
Link: https://lore.kernel.org/r/1595065176-460-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 1f58cca5cf ("PCI: Add Loongson PCI Controller support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
As reported in https://bugzilla.kernel.org/206217 , raw_violation_fixup
is causing more harm than good in some common use-cases.
This patch is a partial revert of commit:
191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
and fixes the following regression since then.
* Description:
When both the NIC and MMC are used one can see the following message:
NETDEV WATCHDOG: enp1s0 (r8169): transmit queue 0 timed out
and
pcieport 0000:00:02.0: AER: Uncorrected (Non-Fatal) error received: 0000:01:00.0
r8169 0000:01:00.0: AER: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
r8169 0000:01:00.0: AER: device [10ec:8168] error status/mask=00004000/00400000
r8169 0000:01:00.0: AER: [14] CmpltTO (First)
r8169 0000:01:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:02.0: AER: device recovery failed
After that, the ethernet NIC is not functional anymore even after
reloading the r8169 module. After a reboot, this is reproducible by
copying a large file over the NIC to the MMC.
For some reason this is not reproducible when files are copied to a tmpfs.
* Little background on the fixup, by Manikanta Maddireddy:
"In the internal testing with dGPU on Tegra124, CmplTO is reported by
dGPU. This happened because FIFO queue in AFI(AXI to PCIe) module
get full by upstream posted writes. Back to back upstream writes
interleaved with infrequent reads, triggers RAW violation and CmpltTO.
This is fixed by reducing the posted write credits and by changing
updateFC timer frequency. These settings are fixed after stress test.
In the current case, RTL NIC is also reporting CmplTO. These settings
seems to be aggravating the issue instead of fixing it."
Link: https://lore.kernel.org/r/20200718100710.15398-1-kwizart@gmail.com
Fixes: 191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Cc: stable@vger.kernel.org
According to the Armada XP datasheet, section 10.2.6: "in order for
the device to do a write to the MSI doorbell address, it needs to write
to a register in the internal registers space".
As a result of the requirement above, without this patch, MSI won't
function and therefore some devices won't operate properly without
pci=nomsi.
This requirement was not present at the time of writing this driver
since the vendor u-boot always initializes all PCIe controllers
(incl. BAR0 initialization) and for some time, the vendor u-boot was
the only available bootloader for this driver's SoCs (e.g. A38x,A37x,
etc).
Tested on an Armada 385 board on mainline u-boot (2020.4), without
u-boot PCI initialization and the following PCIe devices:
- Wilocity Wil6200 rev 2 (wil6210)
- Qualcomm Atheros QCA6174 (ath10k_pci)
Both failed to get a response from the device after loading the
firmware and seem to operate properly with this patch.
Link: https://lore.kernel.org/r/20200623060334.108444-1-sh@tkos.co.il
Signed-off-by: Shmuel Hazan <sh@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Release resource in probe failure path (Wei Hu)
- Retry PCI bus D0 entry if device state is invalid (Wei Hu)
- Use struct_size() to help avoid type mistakes (Gustavo A. R. Silva)
* remotes/lorenzo/pci/hv:
PCI: hv: Use struct_size() helper
PCI: hv: Retry PCI bus D0 entry on invalid device state
PCI: hv: Fix the PCI HyperV probe failure path to release resource properly
- Constify struct pci_ecam_ops (Rob Herring)
- Support building as modules (Rob Herring)
- Eliminate wrappers for pci_host_common_probe() by using DT match table
data (Rob Herring)
* remotes/lorenzo/pci/host-generic:
PCI: host-generic: Eliminate pci_host_common_probe wrappers
PCI: host-generic: Support building as modules
PCI: Constify struct pci_ecam_ops
# Conflicts:
# drivers/pci/controller/dwc/pcie-hisi.c
