IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
It turns out that when plugging in VGA cable through USB-C to VGA/DVI
dongle the Connection Manager handshake can take longer time, at least
on Intel Titan Ridge based docks such as Dell WD91TB. This leads to
following error in the dmesg:
thunderbolt 0000:00:0d.3: 3:10: DP tunnel activation failed, aborting
and the display stays blank (because we failed to establish the tunnel).
For this reason increase the timeout to 3s.
Reported-by: Koba Ko <koba.ko@canonical.com>
Cc: stable@vger.kernel.org
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make the description match the core driver and the networking with
Thunderbolt/USB4 prefix. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The default ones should be find but this allows the user to tweak the
credits to get more performance out of the P2P connection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a debug log to this quirk as well so we can see what quirks have
been applied when debugging.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Ring 0 cannot be used for anything else than control channel messages.
For this reason add a check to tb_tunnel_alloc_dma() and fail if someone
tries to do that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both tb_xdomain_enable_paths() and tb_xdomain_disable_paths() expect -1,
not 0, if the corresponding ring is not needed. For this reason change
the driver to use correct value for the rings that are not needed.
Fixes: 180b068942 ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Cc: stable@vger.kernel.org
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be
cleared by writing to Interrupt Mask Clear (IMR) and interrupt
status should be cleared properly at shutdown/init.
This fixes an error where interrupts are left enabled during resume
from hibernation with `CONFIG_USB4=y`.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for rings")
Cc: stable@vger.kernel.org # v6.3
Reported-by: Takashi Iwai <tiwai@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=IcG3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.4 merge window
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
thunderbolt: Make use of SI units from units.h
thunderbolt: Get rid of redundant 'else'
thunderbolt: Refactor DROM reading
thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset
The usb4_port_sb_opcode_err_to_errno() converts from USB4 error codes
to the Linux errno space. In particular, this makes the intention
of the repeating usb4_port_retimer_read() call in the
usb4_port_retimer_nvm_authenticate_status() clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In a couple of places it seems reasonable to use MEGA intead
of explicit number. It makes code more readable and robust.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cppcheck reports
drivers/thunderbolt/nhi.c:74:7: style: Local variable 'bit' shadows outer variable [shadowVariable]
int bit;
^
drivers/thunderbolt/nhi.c:66:6: note: Shadowed declaration
int bit = ring_interrupt_index(ring) & 31;
^
drivers/thunderbolt/nhi.c:74:7: note: Shadow variable
int bit;
^
For readablity rename the outer to interrupt_bit and the innner
to auto_clear_bit.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for ring")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When interrupt auto clear is programmed, any read to the interrupt
status register will clear all interrupts. If two interrupts have
come in before one can be serviced then this will cause lost interrupts.
On AMD USB4 routers this has manifested in odd problems particularly
with long strings of control tranfers such as reading the DROM via bit
banging.
Instead of clearing interrupts automatically, clear the bit corresponding
to the given ring's interrupt in the ISR.
Fixes: 7a1808f82a ("thunderbolt: Handle ring interrupt by reading interrupt status register")
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Anson Tsao <anson.tsao@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
`ring_interrupt_index` doesn't change the data for `ring` so mark it as
const. This is needed by the following patch that disables interrupt
auto clear for rings.
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The NVM reading code has a series of gotos that potentially introduce
unexpected behaviors with retries if something unexpected has failed
to parse.
Refactor the code to remove the gotos and drop the retry logic.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[mw: renamed root switch to host router, split device handling too]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The static function `tb_eeprom_get_drom_offset` has more safety guards
for the DROM offset fetching. Use this instead of just `tb_sw_read`
No intended functional changes.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When tunneling aggregated USB3 (20 Gb/s) the bandwidth values that are
programmed to the ADP_USB3_CS_2 go higher than 4096 and that does not
fit anymore to the 12-bit field. Fix this by scaling the value using
the scale field accordingly.
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Memory for the usb4->margining needs to be relased for the upstream port
of the router as well, even though the debugfs directory gets released
with the router device removal. Fix this.
Fixes: d0f1e0c2a6 ("thunderbolt: Add support for receiver lane margining")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=Kegw
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.3 merge window
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Add missing kernel-doc comment to tb_tunnel_maximum_bandwidth()
thunderbolt: Handle bandwidth allocation mode enablement notification
thunderbolt: Add support for DisplayPort bandwidth allocation mode
thunderbolt: Include the additional DP IN double word in debugfs dump
thunderbolt: Add functions to support DisplayPort bandwidth allocation mode
thunderbolt: Increase timeout of DP OUT adapter handshake
thunderbolt: Take CL states into account when waiting for link to come up
thunderbolt: Improve debug logging in tb_available_bandwidth()
thunderbolt: Log DP adapter type
thunderbolt: Use decimal port number in control and tunnel logs too
thunderbolt: Refactor tb_acpi_add_link()
thunderbolt: Use correct type in tb_port_is_clx_enabled() prototype
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the graphics side enables bandwidth allocation mode the DP IN
adapter sends notification to the connection manager about this.
Currently the handler misses this and tries to allocate 0 Mb/s that then
makes the graphics side to think the request failed.
Fix this by properly handling the enablement notification.
Fixes: 6ce3563520 ("thunderbolt: Add support for DisplayPort bandwidth allocation mode")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 spec defines an optional feature that allows the connection
manager to negotiate with the graphics through DPCD registers changes in
the bandwidth allocation dynamically. This is referred as "bandwidth
allocation mode" in the spec. The connection manager uses DP IN adapters
registers to communicate with the graphics, and also gets notifications
from these adapters when the graphics wants to change the bandwidth
allocation. Both the connection manager and the graphics driver needs to
support this.
We check if the DP IN adapter supports this and if it does enable it
before establishing a DP tunnel. Then we react on DP_BW notifications
coming from the DP IN adapter and update the bandwidth allocation
accordingly (within the maximum common capabilities the DP IN/OUT
support).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When DisplayPort bandwidth allocation mode is supported by the DP IN
adapter it has an extra double word in the adapter config space. Include
this in the debugfs register dump.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes the current timeout is not enough so increase it to 1500 ms
and while there make the loop use ktime instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If CL states are enabled for the link it may be in these states too when
reading the lane adapter state but it will enter CL0 as soon as there is
traffic in the high-speed lanes. Upon discovery we want to make sure
that is accounted as the link being up, otherwise we end up tearing down
the topology with no good reason.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see what is going on when bandwidth is being
allocated for tunneling.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see from the debug logs what type of DisplayPort
adapter is in use or available.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use decimal number instead of hex in port numbers as we have been doing
with other logging functions too. This makes the output more consistent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When firmware connection manager is in use we should not touch the lane
adapter (well or any) configuration space so do this only when we know
that the software connection manager is active.
Fixes: 8e1de70425 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We cannot call PM runtime functions in tb_retimer_scan() because it will
also be called when retimers are scanned from userspace (happens when
there is no device connected on ChromeOS for instance) and at the same
USB4 port runtime resume hook. This leads to hang because neither can
proceed.
Fix this by runtime resuming USB4 ports in tb_scan_port() instead. This
makes sure the ports are runtime PM active when retimers are added under
it while avoiding the reported hang as well.
Reported-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Fixes: 1e56c88ade ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert while loop into do-while with only a single call to
acpi_get_first_physical_node(). No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we return an error even if on-board retimers are found and
that's not expected. Fix this to return an error only if there was one
and 0 otherwise.
Fixes: 1e56c88ade ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_port_is_clx_enabled() generates a valid warning with gcc-13:
drivers/thunderbolt/switch.c:1286:6: error: conflicting types for 'tb_port_is_clx_enabled' due to enum/integer mismatch; have 'bool(struct tb_port *, unsigned int)' ...
drivers/thunderbolt/tb.h:1050:6: note: previous declaration of 'tb_port_is_clx_enabled' with type 'bool(struct tb_port *, enum tb_clx)' ...
I.e. the type of the 2nd parameter of tb_port_is_clx_enabled() in the
declaration is unsigned int, while the definition spells enum tb_clx.
Synchronize them to the former as the parameter is in fact a mask of the
enum values.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Wake on connect/disconnect is only supported while runtime suspend for
now, which is obviously necessary. It is also not inherently desired for
the system to wakeup on Thunderbolt/USB4 hot plug events. However, we
can still make user in control of waking up the system in the events of
hot plug/unplug.
This patch adds 'wakeup' attribute under 'usb4_portX/power' sysfs
attribute and only enables wakes on connect/disconnect to the respective
port when 'wakeup' is set to 'enabled'. The attribute is set to
'disabled' by default.
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Replacing the direct fwnode_property_get_reference_args()
call will this wrapper function.
No functional changes intended.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The variable len is assigned a value that is never read. It is re-assigned
a new value in the following do-while loop and never referenced after
the loop. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/thunderbolt/xdomain.c:344:2: warning: Value stored to 'len' is
never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use str_enabled_disabled() helper instead of open coding the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices supported
and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before,
and some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new
chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices
better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different
USB drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BN9g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yljdgCdH4Fev4Nvf2Nokfv0q0krcRB3YpUAn1aZfpb/
EbgxsxhPnTJg+mmXyLms
=IxUy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki).
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus).
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw).
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus).
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello).
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry).
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen).
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv).
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko).
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello).
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin).
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede).
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner).
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton).
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan).
- Fix Tx acknowledge in the PCC address space handler (Huisong Li).
- Use wait_for_completion_timeout() for PCC mailbox operations (Huisong
Li).
- Release resources on PCC address space setup failure path (Rafael
Mendonca).
- Remove unneeded result variables from APEI code (ye xingchen).
- Print total number of records found during BERT log parsing (Dmitry
Monakhov).
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello).
- Drop unneeded result variable from ec_write() (ye xingchen).
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver (Hanjun
Guo).
- Reorder symbols to get rid of a few forward declarations in the ACPI
fan driver (Uwe Kleine-König).
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander).
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam).
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki).
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang).
- Do not initialize ret in main() in the pfrut utility (Shi junming).
- Drop useless ACPI DSDT override documentation (Rafael Wysocki).
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare).
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into an
integer value (Andy Shevchenko).
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko).
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui).
-----BEGIN PGP SIGNATURE-----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=xyUK
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"ACPI and PNP updates for 6.1-rc1.
These rearrange the ACPI device object initialization code (to get rid
of a redundant parent pointer from struct acpi_device among other
things), unify the _UID handling, drop support for some _OSI strings
that should not be necessary any more, add new IDs to support more
hardware and some more quirks, fix a few issues and clean up code all
over.
Specifics:
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki)
- Rename ACPI device object reference counting functions (Rafael
Wysocki)
- Rearrange ACPI device object initialization code (Rafael Wysocki)
- Drop parent field from struct acpi_device (Rafael Wysocki)
- Extend the the int3472-tps68470 driver to support multiple
consumers of a single TPS68470 along with the requisite
framework-level support (Daniel Scally)
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus)
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw)
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus)
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello)
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry)
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen)
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv)
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko)
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello)
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin)
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede)
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner)
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton)
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan)
- Fix Tx acknowledge in the PCC address space handler (Huisong Li)
- Use wait_for_completion_timeout() for PCC mailbox operations
(Huisong Li)
- Release resources on PCC address space setup failure path (Rafael
Mendonca)
- Remove unneeded result variables from APEI code (ye xingchen)
- Print total number of records found during BERT log parsing (Dmitry
Monakhov)
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello)
- Drop unneeded result variable from ec_write() (ye xingchen)
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver
(Hanjun Guo)
- Reorder symbols to get rid of a few forward declarations in the
ACPI fan driver (Uwe Kleine-König)
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander)
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam)
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki)
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang)
- Do not initialize ret in main() in the pfrut utility (Shi junming)
- Drop useless ACPI DSDT override documentation (Rafael Wysocki)
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare)
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into
an integer value (Andy Shevchenko)
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko)
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui)"
* tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (79 commits)
ACPI: LPSS: Deduplicate skipping device in acpi_lpss_create_device()
ACPI: LPSS: Replace loop with first entry retrieval
ACPI: x86: s2idle: Add another ID to s2idle_dmi_table
ACPI: x86: s2idle: Fix a NULL pointer dereference
MAINTAINERS: Drop records pointing to 01.org/linux-acpi
ACPI: Kconfig: Drop link to https://01.org/linux-acpi
ACPI: docs: Drop useless DSDT override documentation
ACPI: DPTF: Drop stale link from Kconfig help
ACPI: x86: s2idle: Add a quirk for ASUSTeK COMPUTER INC. ROG Flow X13
ACPI: x86: s2idle: Add a quirk for Lenovo Slim 7 Pro 14ARH7
ACPI: x86: s2idle: Add a quirk for ASUS ROG Zephyrus G14
ACPI: x86: s2idle: Add a quirk for ASUS TUF Gaming A17 FA707RE
ACPI: x86: s2idle: Add module parameter to prefer Microsoft GUID
ACPI: x86: s2idle: If a new AMD _HID is missing assume Rembrandt
ACPI: x86: s2idle: Move _HID handling for AMD systems into structures
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
...
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
This includes following Thunderbolt/USB4 changes for the v6.1 merge
window:
- Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller
- Support for ASMedia USB4 controller NVM firmware upgrade
- Receiver lane margining support
- Few fixes and cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iQJUBAABCgA+FiEEVTdhRGBbNzLrSUBaAP2fSd+ZWKAFAmM0G3ogHG1pa2Eud2Vz
dGVyYmVyZ0BsaW51eC5pbnRlbC5jb20ACgkQAP2fSd+ZWKAhEg/8CuUZvDwLog7O
SbpKAPqGOvDC3EM0VhtJyjJAUVWImVaRuSHAWEHn/XJAICaRTxMJJM7xoJnr+X7O
4VMFzPhF6oF+28VMzy8OLm15kiiNtpXimOKaXNXzoDzJ6aqjgr9KpHSpzhOx3MuF
HUzhoMWk2RHwnrkxlpewU9wJg8ZtG6syI5QV534KsqIwxOcO+8pr7nKz8V8HrUt9
EwFIgU4op/eKCsgeLmotw/8CXI33ezIheMeUdSit3Gqa3Ey9u/JtzVaN7siEOhxy
c3nBO8MgYhKaX0RCVKFGRm/YktFlrECStfDNhgtUbBS2lfoePcaeZGKwuCRpmhkj
WicPxph8m5slKborqGVaoZtgtxqftOt1tWmvnJntqSLcOycPM4bX8gDfWZmoi6JX
f+Vritdy9DDTCE00/Hc2gCpQG0rfX+DzpYvLz4Z8tIa5oU9X5CfCNs8qb20VSQAg
xgmyRe+6/UzJAMKQ7uPy8wSKt/rpKOxsIQC+bhhdiN9g000YS7A56juiC0Z8IfrH
rZae7pvtoD/r7lrJlRcFKtNPup+QrZZ/kdLzWpZbAmKYZ7DkI44KA4iHVBpt24rg
8e23s2/U6ezhNMcR0dLWwIrE+KoiB15BkX9/J1CJxhJLW9lw+fxlSfeZDI0rfjE2
HqcC/Fxx1dMNJykbXAyrO9HYmT551Vs=
=67d1
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
"thunderbolt: Changes for v6.1 merge window
This includes following Thunderbolt/USB4 changes for the v6.1 merge
window:
- Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller
- Support for ASMedia USB4 controller NVM firmware upgrade
- Receiver lane margining support
- Few fixes and cleanups.
All these have been in linux-next with no reported issues."
* tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Explicitly enable lane adapter hotplug events at startup
thunderbolt: Use dev_err_probe()
thunderbolt: Convert to use sysfs_emit()/sysfs_emit_at() APIs
thunderbolt: Fix spelling mistake "simultaneusly" -> "simultaneously"
thunderbolt: debugfs: Fix spelling mistakes in seq_puts text
thunderbolt: Add support for ASMedia NVM image format
thunderbolt: Move vendor specific NVM handling into nvm.c
thunderbolt: Provide tb_retimer_nvm_read() analogous to tb_switch_nvm_read()
thunderbolt: Rename and make nvm_read() available for other files
thunderbolt: Extend NVM version fields to 32-bits
thunderbolt: Allow NVM upgrade of USB4 host routers
thunderbolt: Add support for receiver lane margining
thunderbolt: Add helper to check if CL states are enabled on port
thunderbolt: Pass CL state bitmask to tb_port_clx_supported()
thunderbolt: Move port CL state functions into correct place in switch.c
thunderbolt: Move tb_xdomain_parent() to tb.h
thunderbolt: Add support for Intel Meteor Lake
thunderbolt: Add comment where Thunderbolt 4 PCI IDs start
thunderbolt: Add DP OUT resource when DP tunnel is discovered
This includes a single fix from Mario that resets the plug event delay
back to the USB4 spec value.
This has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=m6dT
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
"thunderbolt: Fix for v6.0 final
This includes a single fix from Mario that resets the plug event delay
back to the USB4 spec value.
This has been in linux-next with no reported issues."
* tag 'thunderbolt-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Explicitly reset plug events delay back to USB4 spec value
Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.
Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Unify error message format by using dev_err_probe().
While at it, use temporary variable for device in
the rest of the messaging calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
While at it, use Elvis operator in some cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here are a few small USB and Thunderbolt driver fixes and new device ids
for 6.0-rc7.
They contain:
- new usb-serial driver ids
- documentation build warning fix in USB hub code
- flexcop-usb long-posted bugfix (the v4l maintainer for this is
MIA so I have finally picked this up as it is a fix for a
reported problem.)
- dwc3 64bit DMA bugfix
- new thunderbolt device ids
- typec build error fix
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYy3Mew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykt8ACg0kKcrj40WNlj9iy3TH2FNBIxXXIAoIMUs4Oe
rw0jU8KQGf+8NAKXwH87
=Q7cc
-----END PGP SIGNATURE-----
Merge tag 'usb-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver fixes and ids from Greg KH:
"Here are a few small USB and Thunderbolt driver fixes and new device
ids for 6.0-rc7.
They contain:
- new usb-serial driver ids
- documentation build warning fix in USB hub code
- flexcop-usb long-posted bugfix (the v4l maintainer for this is MIA
so I have finally picked this up as it is a fix for a reported
problem.)
- dwc3 64bit DMA bugfix
- new thunderbolt device ids
- typec build error fix
All of these have been in linux-next with no reported issues"
* tag 'usb-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: anx7411: Fix build error without CONFIG_POWER_SUPPLY
media: flexcop-usb: fix endpoint type check
USB: serial: option: add Quectel RM520N
USB: serial: option: add Quectel BG95 0x0203 composition
thunderbolt: Add support for Intel Maple Ridge single port controller
usb: dwc3: core: leave default DMA if the controller does not support 64-bit DMA
USB: core: Fix RST error in hub.c
If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.
To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This KUnit fixes update for Linux 6.0-rc5 consists of 2 fixes to test
build and a fix to incorrect taint reason reporting.
-----BEGIN PGP SIGNATURE-----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=xA12
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Two fixes to test build and a fix for incorrect taint reason reporting"
* tag 'linux-kselftest-kunit-fixes-6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
tools: Add new "test" taint to kernel-chktaint
kunit: fix Kconfig for build-in tests USB4 and Nitro Enclaves
kunit: fix assert_type for comparison macros
Add support for Maple Ridge discrete USB4 host controller from Intel
which has a single USB4 port (versus the already supported dual port
Maple Ridge USB4 host controller).
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are a handful of spelling mistakes in seq_puts text. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add support for ASMedia specific NVM image format. This makes it
possible to upgrade the NVM firmware of ASMedia routers in addition to
Intel ones.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As there will be more USB4 devices that support NVM firmware upgrade from
various vendors, it makes sense to split out the Intel specific NVM
image handling from the generic code. This moves the Intel specific NVM
handling into a new structure that will be matched by the device type
and the vendor ID. Do this for both routers and retimers.
This makes it easier to extend the NVM support to cover new vendors and
NVM image formats in the future.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As we are moving the NVM vendor specifics into nvm.c we need to deal
witht he retimer NVM formats too. For this reason provide retimer
specific function that can be used to read the contents of the NVM and
rename the internal ones accordingly analogous to what we do with
routers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to support non-Intel NVM formats the vendor specific NVM
validation code that will live in nvm.c needs to be able to read various
parts of the NVM so make the function available outside of switch.c and
rename it accordingly.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to support non-Intel NVM image formats extend the NVM major and
minor version to 32-bits to better accommondate different versioning
schemes.
No functional impact.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel pre-USB4 host routers required the firmware connection manager to
be active in order to perform NVM firmware upgrade and for this reason
it was disabled when software connection manager is active. However,
this is not necessary for USB4 host routers as this functionality is
part of router operations that the router implements if it wants to
support this.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines standard set of registers to be used for receiver lane
margining. This is useful for I/O interface quality and electrical
robustness validation during manufacturing. Expose receiver lane
margining through new debugfs directory "margining" that is added under
each connected USB4 port. Users can then run the margining by writing to
the exposed attributes under that directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of testing just a single CL state we can pass a bitmask of
states to check. This makes it simpler for callers of the function.
We also add a check for CL2 even though not fully supported by the
driver yet.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
They should be close to other functions dealing with USB4 ports. No
functional impact.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to need this for lane margining support so make it
available outside of xdomain.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both the USB4 and Nitro Enclaves KUNIT tests are now able to be compiled
if KUNIT is compiled as a module. This leads to issues if KUNIT is being
packaged separately from the core kernel and when KUNIT is run baremetal
without the required driver compiled into the kernel.
Fixes: 635dcd1684 ("thunderbolt: test: Use kunit_test_suite() macro")
Fixes: fe5be808fa ("nitro_enclaves: test: Use kunit_test_suite() macro")
Signed-off-by: Nico Pache <npache@redhat.com>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Andra Paraschiv <andraprs@amazon.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
As we are now enabling full end-to-end flow control to the Thunderbolt
networking driver, in order for it to work properly on second generation
Thunderbolt hardware (Falcon Ridge), we need to add back the workaround
that was removed with commit 53f13319d1 ("thunderbolt: Get rid of E2E
workaround"). However, this time we only apply it for Falcon Ridge
controllers as a form of an additional quirk. For non-Falcon Ridge this
does nothing.
While there fix a typo 'reqister' -> 'register' in the comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following what we do for routers already, extend this to XDomain
connections as well. This will show in sysfs whether the link is in USB4
or Thunderbolt mode.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parent field in struct acpi_device is, in fact, redundant,
because the dev.parent field in it effectively points to the same
object and it is used by the driver core.
Accordingly, the parent field can be dropped from struct acpi_device
and for this purpose define acpi_dev_parent() to retrieve a parent
struct acpi_device pointer from the dev.parent field in struct
acpi_device. Next, update all of the users of the parent field
in struct acpi_device to use acpi_dev_parent() instead of it and
drop it.
While at it, drop the ACPI_IS_ROOT_DEVICE() macro that is only used
in one place in a confusing way.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
Intel Meteor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. Add the Intel Meteor Lake PCI IDs to the driver list
of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.
Fixes: 30a4eca69b ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e19 ("thunderbolt: Let the connection manager handle all notifications")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the boot firmware implements a connection manager of its own it may
create a DisplayPort tunnel and will be handed off to Linux connection
manager, but the DP OUT resource is not saved in the dp_resource list.
This patch adds tunnelled DP OUT port to the dp_resource list once the
DP tunnel is discovered.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Tested-by: Renjith Pananchikkal <Renjith.Pananchikkal@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development on
some new hardware support and cleanups of older drivers. Highlights of
this pull request are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this
tool it seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted
as they depened on some typec changes, but the cross-tree
merges caused problems so they will come back later through
the platform tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYup5Rg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yko/ACfYD9mdlr4WleUpVw5/uNywN6sL9EAn1tv0V8W
cUTAoWxAf5orClAC22ZU
=Vcqd
-----END PGP SIGNATURE-----
Merge tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
This KUnit update for Linux 5.20-rc1 consists of several fixes and an
important feature to discourage running KUnit tests on production
systems. Running tests on a production system could leave the system
in a bad state. This new feature adds:
- adds a new taint type, TAINT_TEST to signal that a test has been run.
This should discourage people from running these tests on production
systems, and to make it easier to tell if tests have been run
accidentally (by loading the wrong configuration, etc.)
- several documentation and tool enhancements and fixes.
-----BEGIN PGP SIGNATURE-----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=WzBX
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
The new implementation of kunit_test_suite() for modules no longer
conflicts with module_init, so can now be used by the thunderbolt tests.
Also update the Kconfig entry to enable the test when KUNIT_ALL_TESTS is
enabled.
This means that kunit_tool can now successfully run and parse the test
results with, for example:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_PCI=y --kconfig_add CONFIG_USB4=y \
'thunderbolt'
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Use acpi_find_child_by_adr() to find the child matching a given bus
address instead of tb_acpi_find_port() that walks the list of children
of an ACPI device directly for this purpose and drop the latter.
Apart from simplifying the code, this will help to eliminate the
children list head from struct acpi_device as it is redundant and it
is used in questionable ways in some places (in particular, locking is
needed for walking the list pointed to it safely, but it is often
missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Intel Raptor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. By default it is still using firmware based connection
manager so we can use most of the Alder Lake flows.
Signed-off-by: George D Sworo <george.d.sworo@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove some warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/thunderbolt/ctl.c:701: warning: expecting prototype for tb_cfg_start().
Prototype was for tb_ctl_start() instead
drivers/thunderbolt/ctl.c:722: warning: expecting prototype for tb_ctrl_stop().
Prototype was for tb_ctl_stop() instead
drivers/thunderbolt/ctl.c:930: warning: expecting prototype for tb_cfg_write().
Prototype was for tb_cfg_write_raw() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here we configure TMU mode to HiFi uni-directional once DP tunnel
is created. This is due to accuracy requirement for DP tunneling
as appears in CM guide 1.0, section 7.3.2.
Due to Intel hardware limitation, once we changed the TMU mode to HiFi
uni-directional (when DP tunnel exists), we don't change TMU mode back to
normal uni-directional, even if DP tunnel is torn down later.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case of uni-directional time sync, TMU handshake is
initiated by upstream router. In case of bi-directional
time sync, TMU handshake is initiated by downstream router.
In order to handle correctly the case of uni-directional mode,
we avoid changing the upstream router's rate to off,
because it might have another downstream router plugged that is set to
uni-directional mode (and we don't want to change its mode).
Instead, we always change downstream router's rate.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Disable CLx before system suspended only if previously was enabled.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We can't enable CLx if it is not supported either by the host or device,
or by the USB4/TBT link (e.g. when an optical cable is used).
We silently ignore CLx enabling in this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Including:
- Intel VT-d driver updates
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU
legacy binding
- Minor cleanups
- Patches to fix a BUG_ON in the vfio_iommu_group_notifier
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group
is either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Patches to make forcing of cache-coherent DMA more coherent
between IOMMU drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEr9jSbILcajRFYWYyK/BELZcBGuMFAmKWCbUACgkQK/BELZcB
GuPHmRAAuoH9iK/jrC3SgrqpBfH2iRN7ovIX8dFvgbQWX27lhXF4gvj2/nYdIvPK
75j/LmdibuzV3Iez4kjbGKNG1AikwK3dKIH21a84f3ctnoamQyL6nMfCVBFaVD/D
kvPpTHyjbGPNf6KZyWQdkJ5DXD1aoG1DKkBnslH5pTNPqGuNqbcnRTg0YxiJFLBv
5w2B6jL06XRzunh+Sp1Dbj+po8ROjLRCEU+tdrndO8W/Dyp6+ZNNuxL9/3BM9zMj
py0M4piFtGnhmJSdym1eeHm7r1YRjkZw+MN+e8NcrcSihmDutEWo7nRRxA5uVaa+
3O2DNERqCvQUYxfNRUOKwzV8v51GYQHEPhvOe/MLgaEQDmDmlF2dHNGm93eCMdrv
m1cT011oU7pa4qHomwLyTJxSsR7FzJ37igq/WeY++MBhl+frqfzEQPVxF+W7GLb8
QvT/+woCPzLVpJbE7s0FUD4nbPd8c1dAz4+HO1DajxILIOTq1bnPIorSjgXODRjq
yzsiP1rAg0L0PsL7pXn3cPMzNCE//xtOsRsAGmaVv6wBoMLyWVFCU/wjPEdjrSWA
nXpAuCL84uxCEl/KLYMsg9UhjT6ko7CuKdsybIG9zNIiUau43uSqgTen0xCpYt0i
m//O/X3tPyxmoLKRW+XVehGOrBZW+qrQny6hk/Zex+6UJQqVMTA=
=W0hj
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel VT-d driver updates:
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates:
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU legacy
binding
- Minor cleanups
- Fix a BUG_ON in the vfio_iommu_group_notifier:
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group is
either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Make forcing of cache-coherent DMA more coherent between IOMMU
drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu/amd: Increase timeout waiting for GA log enablement
iommu/s390: Tolerate repeat attach_dev calls
iommu/vt-d: Remove hard coding PGSNP bit in PASID entries
iommu/vt-d: Remove domain_update_iommu_snooping()
iommu/vt-d: Check domain force_snooping against attached devices
iommu/vt-d: Block force-snoop domain attaching if no SC support
iommu/vt-d: Size Page Request Queue to avoid overflow condition
iommu/vt-d: Fold dmar_insert_one_dev_info() into its caller
iommu/vt-d: Change return type of dmar_insert_one_dev_info()
iommu/vt-d: Remove unneeded validity check on dev
iommu/dma: Explicitly sort PCI DMA windows
iommu/dma: Fix iova map result check bug
iommu/mediatek: Fix NULL pointer dereference when printing dev_name
iommu: iommu_group_claim_dma_owner() must always assign a domain
iommu/arm-smmu: Force identity domains for legacy binding
iommu/arm-smmu: Support Tegra234 SMMU
dt-bindings: arm-smmu: Add compatible for Tegra234 SOC
dt-bindings: arm-smmu: Document nvidia,memory-controller property
iommu/arm-smmu-qcom: Add SC8280XP support
dt-bindings: arm-smmu: Add compatible for Qualcomm SC8280XP
...
Add a KUnit test to check that buffer allocation works also for devices
with no DP adapters.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the case of a device without DisplayPort adapters we calculate
incorrectly the amount of buffers. Fix the calculation for this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Inter-Domain Service specification defines a protocol that can
be used to establish lane bonding between two USB4 domains (hosts). So
far we have not implemented it because the host controller DMA was not
fast enough to be able to go over 20 Gbits/s even if lanes were bonded.
However, starting from Intel Alder Lake CPUs the DMA can go over
20 Gbits/s so now it makes more sense to add this support to the driver.
Because both ends need to negotiate the bonding we add a simple state
machine that tracks the connection state and does the necessary steps
described by the USB4 Inter-Domain Service specification. We only
establish lane bonding when both sides of the link support it. Otherwise
we default to use the single lane. Also this is only done when software
connection manager is used. On systems with firmware based connection
manager, it handles the high-speed tunneling so bonding lanes is
specific to the implementation (Intel firmware based connection manager
does not support lane bonding).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes when polling for the port after target link width is changed
we get back port locked notification (because the link actually was
reset and then re-trained). Instead of bailing out we can ignore these
when polling for the width change as this is expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When bonding lanes over XDomain the host that has "higher" UUID triggers
link re-train for bonding, and the host that has "lower" UUID just waits
for this to happen. To support this split setting the link width and
triggering the actual bonding a separate functions that can be called as
needed.
While there remove duplicated empty line in the kernel-doc comment of
tb_port_lane_bonding_disable().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This should be before tb_wait_for_port() following how the functions in
switch.c are organized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Creating a symlink pointing to the correct USB Type-C
connector for the on-board USB4 ports when they are created.
The link will be created only if the firmware is able to
describe the connection between the port and its connector.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Won Chung <wonchung@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Between me trying to get rid of iommu_present() and Mario wanting to
support the AMD equivalent of DMAR_PLATFORM_OPT_IN, scrutiny has shown
that the iommu_dma_protection attribute is being far too optimistic.
Even if an IOMMU might be present for some PCI segment in the system,
that doesn't necessarily mean it provides translation for the device(s)
we care about. Furthermore, all that DMAR_PLATFORM_OPT_IN really does
is tell us that memory was protected before the kernel was loaded, and
prevent the user from disabling the intel-iommu driver entirely. While
that lets us assume kernel integrity, what matters for actual runtime
DMA protection is whether we trust individual devices, based on the
"external facing" property that we expect firmware to describe for
Thunderbolt ports.
It's proven challenging to determine the appropriate ports accurately
given the variety of possible topologies, so while still not getting a
perfect answer, by putting enough faith in firmware we can at least get
a good bit closer. If we can see that any device near a Thunderbolt NHI
has all the requisites for Kernel DMA Protection, chances are that it
*is* a relevant port, but moreover that implies that firmware is playing
the game overall, so we'll use that to assume that all Thunderbolt ports
should be correctly marked and thus will end up fully protected.
CC: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/b153f208bc9eafab5105bad0358b77366509d2d4.1650878781.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Brad reported that on Apple hardware with Light Ridge or Falcon Ridge
controller, plugging in a chain of Thunderbolt displays (Light Ridge
based controllers) causes all kinds of tearing and flickering. The
reason for this is that on Thunderbolt 1 hardware there is no lane
bonding so we have two independent 10 Gb/s lanes, and currently Linux
tunnels both displays through the lane 1. This makes the displays to
share the 10 Gb/s bandwidth which may not be enough for higher
resolutions.
For this reason make the second tunnel go through the lane 0 instead.
This seems to match what the macOS connection manager is also doing.
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
This is useful when debugging possible issues during tunnel discovery.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
This makes it consistent with the other logging functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Should be 'in' instead of 'bin'. Fix it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Replace the NULL checks with the more specific and idiomatic NULL macros.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
The structure `tb_eeprom_ctl` is used to show the bits accessed when
reading/writing EEPROM.
As this structure is specified in the USB4 spec as `VSC_CS_4` update
the names and use of members to match the specification. This should not
change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 1.0 specification outlines the `cap_plug_events` structure as
`VSC_CS_1`. This shows that 4 bits of `VSC_CS_1` are TBT3 compatible in
USB4, but TBT3 controllers also support disabling XHCI.
Update the names and comments to more closely match the specification.
This should not change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 specification doesn't make any requirements that reading
a device router's DROM is needed for the operation of the device.
Other connection manager solutions don't necessarily read it or gate
the usability of the device on whether it was read.
So make failures when reading the DROM show warnings but not
fail the initialization of the router.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Routers might not have a UID set if the DROM read failed during
initialization previously.
Normally upon resume the UID is re-read to confirm it's the same
device connected.
* If the DROM read failed during init but then succeeded during
resume it could either be a new device or faulty device
* If the DROM read failed during init and also failed during resume
it might be a different device plugged in all together.
Detect this situation and prevent re-using the same configuration in
these cirucmstances.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently DROM reads are only retried in the case that parsing failed.
However if the size or CRC fails, then there should also be a retry.
This helps with reading the DROM on TBT3 devices connected to AMD
Yellow Carp which will sometimes fail on the first attempt.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since nvmem_unregister() checks for NULL, no need to repeat in
the caller. Drop duplicate NULL checks.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220220151527.17216-14-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_is_alpine_ridge() is missing device ID for Intel Alpine Ridge
dual port version so add this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge does not disable AUX timers when it gets SET_CONFIG
with SET_LTTPR_MODE set which makes DP tunneling to fail. For this
reason disable LTTPR on Titan Ridge device side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
While at it, include directly <linux/dma-mapping.h> instead on relying on
indirect inclusion.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a module parameter that allows user to completely disable CLx
functionality in case problems are found.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rename the VSC capability: TB_VSE_CAP_IECS to TB_VSE_CAP_CP_LP to follow
the Intel devices namings as appear in the datasheet. This capability
is used for controlling CLx (Low Power states of the link).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up until Titan Ridge (Thunderbolt 3) device routers only supported
bi-directional mode. In this patch we add to TMU a uni-directional mode.
The uni-directional mode is needed for enabling of low power state of
the link (CLx).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kmemdup() may return NULL if there is not enough memory available. Check
this and bail out early in this case. While there move INIT_WORK() to
happen after we have allocated all the memory needed for the event
handling to avoid doing unnecessary work.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device.
Instead, use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
These fields are marked read-only for USB4 routers so do not touch them
in that case. Update the kernel-doc of tb_dp_port_set_hops() to reflect
this too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This might happen if the boot firmware uses different amount of NFC
credits than what the router suggests, or we are dealing with pre-USB4
device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes when plugging in a USB4 device we might see following error:
thunderbolt 1-0:3.1: runtime PM trying to activate child device 1-0:3.1 but parent (usb4_port3) is not active
This happens because the parent USB4 port was still runtime suspended.
Fix this by runtime resuming the USB4 port before scanning the retimers
below it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If protocol tunnels are already up when the driver is loaded, for
instance if the boot firmware implements connection manager of its own,
runtime PM reference count of the consumer devices behind the tunnel
might have been increased already before the device link is created but
the supplier device runtime PM reference count is not. This leads to a
situation where the supplier (the Thunderbolt driver) can runtime
suspend even if it should not because the corresponding protocol tunnel
needs to be up causing the devices to be removed from the corresponding
native bus.
Prevent this from happening by making both sides of the link runtime PM
active briefly. The pm_runtime_put() for the consumer (PCIe
root/downstream port, xHCI) then allows it to runtime suspend again but
keeps the supplier runtime resumed the whole time it is runtime active.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
tb_xdp_properties_changed_request() was calling tb_xdp_handle_error() with
a struct tb_xdp_properties_changed_response on the stack, which does not
have the "error" field present when cast to struct tb_xdp_error_response.
This was detected when building with -Warray-bounds:
drivers/thunderbolt/xdomain.c: In function 'tb_xdomain_properties_changed':
drivers/thunderbolt/xdomain.c:226:22: error: array subscript 'const struct tb_xdp_error_response[0]' is partly outside array bounds of 'struct tb_xdp_properties_changed_response[1]' [-Werror=array-bounds]
226 | switch (error->error) {
| ~~~~~^~~~~~~
drivers/thunderbolt/xdomain.c:448:51: note: while referencing 'res'
448 | struct tb_xdp_properties_changed_response res;
| ^~~
Add union containing struct tb_xdp_error_response to structures passed
to tb_xdp_handle_error(), so that the "error" field will be present.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v5.16 merge
window:
* Re-enable retry logic for control packets in domain needed by some
controllers when software connection manager is being used
* Fix -Wrestrict build warning emitted by gcc-11.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=xKvr
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.16 merge window
This includes following Thunderbolt/USB4 changes for the v5.16 merge
window:
* Re-enable retry logic for control packets in domain needed by some
controllers when software connection manager is being used
* Fix -Wrestrict build warning emitted by gcc-11.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix -Wrestrict warning
thunderbolt: Enable retry logic for intra-domain control packets
The structleak plugin causes the stack frame size to grow immensely when
used with KUnit:
drivers/thunderbolt/test.c:1529:1: error: the frame size of 1176 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Turn it off in this file.
Linus already split up tests in this file, so this change *should* be
redundant now.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
gcc-11 warns when building with W=1:
drivers/thunderbolt/xdomain.c: In function 'modalias_show':
drivers/thunderbolt/xdomain.c:733:16: error: 'sprintf' argument 3 overlaps destination object 'buf' [-Werror=restrict]
733 | return sprintf(buf, "%s\n", buf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/thunderbolt/xdomain.c:727:36: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
727 | char *buf)
| ~~~~~~^~~
There is no need for the sprintf() here when a strcat() does
the same thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case of software connection manager, the response packets are lost
sometimes within the stipulated time. Hence resending the control
packets in such scenario by increasing the retry count TB_CTL_RETRIES
value.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The tb_test_credit_alloc_all() function had a huge number of
KUNIT_ASSERT() statements, all of which (though the magic of many many
layers of inscrutable macros) ended up allocating and initializing
various test assertion structures on the stack.
Don't do that. The kernel stack isn't infinite, and we have compiler
warnings (now errors) for the case where a stack frame grows too large.
Like it did here, by not an inconsiderable margin:
drivers/thunderbolt/test.c: In function ‘tb_test_credit_alloc_all’:
drivers/thunderbolt/test.c:2367:1: error: the frame size of 4500 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
2367 | }
| ^
Solve this similarly to the lib/test_scanf case: split out the tests
into several smaller functions, each just testing one particular tunnel
credit allocation.
This makes the i386 allyesconfig build work for me again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a number
of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9+Tw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqyQCgxWjp4VD9Ycbz1XsHRIkkERWj6WgAnRe4mCpG
n5csYXATbYUD0UdH0hru
=xZCV
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=1bPR
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.15 merge window
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix port linking by checking all adapters
thunderbolt: Do not read control adapter config space
thunderbolt: Handle ring interrupt by reading interrupt status register
thunderbolt: Add vendor specific NHI quirk for auto-clearing interrupt status
thunderbolt: Add authorized value to the KOBJ_CHANGE uevent
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Adapter 0 is the control adapter and as per USB4 spec in section 2.2.6.2
control Adapters do not have an adapter configuration space.
For this reason skip reading adapter config space in tb_port_init() when
the port number is 0. This actually simplifies the rest of the function
as we don't need to check for the port->port == 0 anymore.
While there drop the extra empty line at the end of the function.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As per USB4 specification by default "Disable ISR Auto-Clear" bit is set
to zero and the Tx/Rx ring interrupt status needs to be cleared.
Hence handle it by reading the interrupt status register (ISR) in the
MSI-X handler.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce nhi_check_quirks() routine to handle any vendor specific quirks
to manage a hardware specific implementation.
On Intel hardware the USB4 controller supports clearing the interrupt
status register automatically right after it is being issued. For this
reason add a new quirk that does that on all Intel hardware.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For security reasons, we would like to monitor and track when the
Thunderbolt devices are authorized and deauthorized (i.e. when the
Thunderbolt sysfs "authorized" attribute changes). Currently the
userspace gets a udev change notification when there is a change, but
the state may have changed (again) by the time we look at the authorized
attribute in sysfs. So an authorization event may go unnoticed. Thus
make it easier by informing the actual change (new value of authorized
attribute) in the udev change notification.
The change is included as a key value "authorized=<val>" where <val>
is the new value of sysfs attribute "authorized", and is described at
Documentation/ABI/testing/sysfs-bus-thunderbolt under
/sys/bus/thunderbolt/devices/.../authorized.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----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=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
Partially revert "thunderbolt: test: Remove some casts which are no
longer required". It turns out that typeof() doesn't support bitfields,
so these still need to be cast to the appropriate enum.
The only mention of typeof() and bitfields I can find is in the proposal
to standardise them:
http://www.open-std.org/jtc1/sc22/wg14/www/docs/n2619.htm
This was caught by the kernel test robot:
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/FDKBHAV7QNLNFU5NBI2RKV56DWDSOLGM/
Fixes: 8f0877c26e ("thunderbolt: test: Remove some casts which are no longer required")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With some of the stricter type checking in KUnit's EXPECT macros
removed, several casts in the thunderbolt KUnit tests are no longer
required.
Remove the unnecessary casts, making the conditions clearer.
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
DROM for USB4 host/device has a shorter header than Thunderbolt DROM
header. This patch addresses host/device with USB4 DROM (According to spec:
Universal Serial Bus 4 (USB4) Device ROM Specification, Rev 1.0, Feb-2021).
While there correct the data_len field to be 12 bits and rename
__unknown1 to reserved following the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Alder Lake has the same integrated Thunderbolt/USB4 controller as
Intel Tiger Lake. By default it is still using firmware based connection
manager so we can use most of the Tiger Lake flows.
Add the Alder Lake PCI IDs to the driver list of supported devices.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This include is not needed so drop it.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Intel Tiger Lake and beyond it takes some time after the force power
is set until the firmware connection manager is ready. So instead of
reading it once we poll it for 10ms before giving up.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We only need to set up the device links when software connection manager
path is used. The firmware connection manager does not need them and if
they are present they may even cause problems.
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should not dereference ->dual_link_port if it is NULL and lane bonding
is requested. For this reason move lane bonding configuration happen
inside the block where ->dual_link_port != NULL.
Fixes: 54509f5005 ("thunderbolt: Add KUnit tests for path walking")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the NVM authentication fails immediately, like if the firmware
detects that the image is not valid for some reason, better to read the
status once and if set to non-zero fail the operation accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.
This is not supported with Thunderbolt 1-3 devices, though.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.
Also add tb_ prefix to the enum while there.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically retimers can be accessed only when the USB4 link is up (e.g
there is a cable connected). However, sometimes it is useful to be able
to access retimers even if there is nothing connected to the USB4 port.
For instance we may still want to be able to upgrade the retimer NVM
firmware even if the user does not have any USB4 devices. This is
something that USB4 spec leaves to implementers.
In case of ACPI based systems, we can support this by providing a
special _DSM method under each USB4 port. This _DSM can be used to turn
on power to on-board retimers (and cycle it through different modes so
that the sideband becomes usable).
This patch adds support for this _DSM and makes the functionality
available to the rest of the driver through tb_acpi_power_[on|off]_retimers().
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upstream port can be connected to any previous generation
Thunderbolt port so logging as "TBT" is more accurate than "TBT3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Goshen Ridge reports wrong DP main credits in NVM 27 and earlier,
so add a quirk that fixes it. We also need to expand the quirk table to
match on hardware vendor/device IDs too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Connection Manager guide provides detailed information how the
USB4 router buffer (credit) allocation information should be used by the
connection manager when it allocates buffers for different paths. This
patch implements it for Linux. For USB 3.x and DisplayPort we use
directly the router preferences. The rest of the buffer space is then
used for PCIe and DMA (peer-to-peer, XDomain) traffic. DMA tunnels
require at least one buffer and PCIe six, so if there is not enough
buffers we fail the tunnel creation.
For the legacy Thunderbolt 1-3 devices we use the existing hard-coded
scheme except for DMA where we use the values suggested by the USB4 spec
chapter 13.
Co-developed-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Once lane bonding has been enabled (or disabled) both lane adapters may
update their total credits accordingly. For this reason re-read the port
credits after lane bonding has been enabled or disabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.
Read this information and store it as part of struct tb_switch for each
USB4 router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It may take some time until the two lanes enter bonded state so poll for
the link width to match what is expected before going forward. This ensures
the link is in expected state before we start establishing paths through
it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
With the USB4 buffer allocation the number of credits (and non-flow
credits) may be different depending on the router buffer allocation
preferences. To allow this move the nfc_credits field to struct
tb_path_hop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The function does not modify the object in any way so make the parameter
const to reflect this.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Configuration Manager guide suggests that the USB4 port wakes
are configured in a certain way, like that when the port is configured
the wake-on-connect should not be set and so forth, so align the driver
with this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.
Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that we have generic functionality available in nvm.c make the DMA
port code call it instead of duplicating the functionality.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We do this for Thunderbolt 2/3 devices through DMA port, USB4 devices
and retimers pretty much the same way. Only the actual block read/write
is different. For this reason split out the NVM read/write functions
from usb4.c to nvm.c and make USB4 device code call these when needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add new device known to support self-authenticate on disconnect.
Signed-off-by: Crag Wang <crag.wang@dell.com>
Reviewed-by: Mario Limonciello <mario.limonciello@outlook.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up to 64 bytes of data can be read from NVM in one go.
Read address must be dword aligned. Data is read into a local buffer.
If caller asks to read data starting at an unaligned address then full
dword is anyway read from NVM into a local buffer. Data is then copied
from the local buffer starting at the unaligned offset to the caller
buffer.
In cases where asked data length + unaligned offset is over 64 bytes
we need to make sure we don't read past the 64 bytes in the local
buffer when copying to caller buffer, and make sure that we don't
skip copying unaligned offset bytes from local buffer anymore after
the first round of 64 byte NVM data read.
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up to 64 bytes of data can be read from NVM in one go. Read address
must be dword aligned. Data is read into a local buffer.
If caller asks to read data starting at an unaligned address then full
dword is anyway read from NVM into a local buffer. Data is then copied
from the local buffer starting at the unaligned offset to the caller
buffer.
In cases where asked data length + unaligned offset is over 64 bytes
we need to make sure we don't read past the 64 bytes in the local
buffer when copying to caller buffer, and make sure that we don't
skip copying unaligned offset bytes from local buffer anymore after
the first round of 64 byte NVM data read.
Fixes: 3e13676862 ("thunderbolt: Add support for DMA configuration based mailbox")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
-----BEGIN PGP SIGNATURE-----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=RzJl
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.13 merge window
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
* tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (24 commits)
thunderbolt: Hide authorized attribute if router does not support PCIe tunnels
thunderbolt: Add details to router uevent
thunderbolt: Unlock on error path in tb_domain_add()
thunderbolt: Add support for USB4 DROM
thunderbolt: Check quirks in tb_switch_add()
thunderbolt: Add KUnit tests for DMA tunnels
thunderbolt: Add KUnit tests for XDomain properties
net: thunderbolt: Align the driver to the USB4 networking spec
thunderbolt: Allow multiple DMA tunnels over a single XDomain connection
thunderbolt: Drop unused tb_port_set_initial_credits()
thunderbolt: Use dedicated flow control for DMA tunnels
thunderbolt: Add support for maxhopid XDomain property
thunderbolt: Add tb_property_copy_dir()
thunderbolt: Align XDomain protocol timeouts with the spec
thunderbolt: Use pseudo-random number as initial property block generation
thunderbolt: Do not re-establish XDomain DMA paths automatically
thunderbolt: Add more logging to XDomain connections
Documentation / thunderbolt: Drop speed/lanes entries for XDomain
thunderbolt: Decrease control channel timeout for software connection manager
thunderbolt: Do not pass timeout for tb_cfg_reset()
...
With USB4 devices PCIe tunneling is optional so for device routers
without PCIe upstream adapter it does not make much sense to expose the
authorized attribute. For this reason hide it if PCIe tunneling is not
supported by the device router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose two environment variables for routers as part of the initial
uevent:
USB4_VERSION=1.0
USB4_TYPE=host|device|hub
Userspace can use this information to expose more details about each
connected device. Only USB4 devices have USB4_VERSION but all devices
have USB4_TYPE.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This array uses 1-based indexing so it corrupts memory one element
beyond of the array. Fix it by making the array one element larger.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After the device_register() succeeds, then the correct way to clean up
is to call device_unregister(). The unregister calls both device_del()
and device_put(). Since this code was only device_del() it results in
a memory leak.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We accidentally deleted this unlock on the error path. Undelete it.
Fixes: 7f0a34d790 ("thunderbolt: Decrease control channel timeout for software connection manager")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 router DROM differs sligthly from Thunderbolt 1-3 DROM. For
instance it does not include UID and CRC8 in the header section, and it
has product descriptor genereric entry to describe the product IDs and
related information. If the "Version" field in the DROM header section
reads 3 it means the router only has USB4 DROM and if it reads 1 it
means the router supports TBT3 compatible DROM.
For this reason, update the DROM parsing code to support "pure" USB4
DROMs too.
While there drop the extra empty line at the end of tb_drom_read().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
