fdc5231374
942 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Linus Torvalds
|
556eb8b791 |
Driver core changes for 6.4-rc1
Here is the large set of driver core changes for 6.4-rc1. Once again, a busy development cycle, with lots of changes happening in the driver core in the quest to be able to move "struct bus" and "struct class" into read-only memory, a task now complete with these changes. This will make the future rust interactions with the driver core more "provably correct" as well as providing more obvious lifetime rules for all busses and classes in the kernel. The changes required for this did touch many individual classes and busses as many callbacks were changed to take const * parameters instead. All of these changes have been submitted to the various subsystem maintainers, giving them plenty of time to review, and most of them actually did so. Other than those changes, included in here are a small set of other things: - kobject logging improvements - cacheinfo improvements and updates - obligatory fw_devlink updates and fixes - documentation updates - device property cleanups and const * changes - firwmare loader dependency fixes. All of these have been in linux-next for a while with no reported problems. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5 LEGadNS38k5fs+73UaxV =7K4B -----END PGP SIGNATURE----- Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the large set of driver core changes for 6.4-rc1. Once again, a busy development cycle, with lots of changes happening in the driver core in the quest to be able to move "struct bus" and "struct class" into read-only memory, a task now complete with these changes. This will make the future rust interactions with the driver core more "provably correct" as well as providing more obvious lifetime rules for all busses and classes in the kernel. The changes required for this did touch many individual classes and busses as many callbacks were changed to take const * parameters instead. All of these changes have been submitted to the various subsystem maintainers, giving them plenty of time to review, and most of them actually did so. Other than those changes, included in here are a small set of other things: - kobject logging improvements - cacheinfo improvements and updates - obligatory fw_devlink updates and fixes - documentation updates - device property cleanups and const * changes - firwmare loader dependency fixes. All of these have been in linux-next for a while with no reported problems" * tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits) device property: make device_property functions take const device * driver core: update comments in device_rename() driver core: Don't require dynamic_debug for initcall_debug probe timing firmware_loader: rework crypto dependencies firmware_loader: Strip off \n from customized path zram: fix up permission for the hot_add sysfs file cacheinfo: Add use_arch[|_cache]_info field/function arch_topology: Remove early cacheinfo error message if -ENOENT cacheinfo: Check cache properties are present in DT cacheinfo: Check sib_leaf in cache_leaves_are_shared() cacheinfo: Allow early level detection when DT/ACPI info is missing/broken cacheinfo: Add arm64 early level initializer implementation cacheinfo: Add arch specific early level initializer tty: make tty_class a static const structure driver core: class: remove struct class_interface * from callbacks driver core: class: mark the struct class in struct class_interface constant driver core: class: make class_register() take a const * driver core: class: mark class_release() as taking a const * driver core: remove incorrect comment for device_create* MIPS: vpe-cmp: remove module owner pointer from struct class usage. ... |
||
Bjorn Helgaas
|
1c03b5bfc5 |
Merge branch 'pci/resource'
- Add pci_dev_for_each_resource() and pci_bus_for_each_resource() iterators to simplify loops (Andy Shevchenko) * pci/resource: EISA: Drop unused pci_bus_for_each_resource() index argument PCI: Make pci_bus_for_each_resource() index optional PCI: Document pci_bus_for_each_resource() PCI: Introduce pci_dev_for_each_resource() PCI: Introduce pci_resource_n() |
||
Mika Westerberg
|
e74b2b58ff |
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
All callers of pci_bridge_wait_for_secondary_bus() supply a timeout of PCIE_RESET_READY_POLL_MS, so drop the parameter. Move the definition of PCIE_RESET_READY_POLL_MS into pci.c, the only user. [bhelgaas: extracted from https://lore.kernel.org/r/20230404052714.51315-3-mika.westerberg@linux.intel.com] Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
Andy Shevchenko
|
02992064bd |
PCI: Make pci_bus_for_each_resource() index optional
Refactor pci_bus_for_each_resource() in the same way as pci_dev_for_each_resource(). This allows the index to be hidden inside the implementation so the caller can omit it when it's not used otherwise. No functional changes intended. Link: https://lore.kernel.org/r/20230330162434.35055-6-andriy.shevchenko@linux.intel.com Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> |
||
Greg Kroah-Hartman
|
75cff725d9 |
driver core: bus: mark the struct bus_type for sysfs callbacks as constant
struct bus_type should never be modified in a sysfs callback as there is nothing in the structure to modify, and frankly, the structure is almost never used in a sysfs callback, so mark it as constant to allow struct bus_type to be moved to read-only memory. Cc: "David S. Miller" <davem@davemloft.net> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Alison Schofield <alison.schofield@intel.com> Cc: Ben Widawsky <bwidawsk@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Harald Freudenberger <freude@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Hu Haowen <src.res@email.cn> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Stuart Yoder <stuyoder@gmail.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: Yanteng Si <siyanteng@loongson.cn> Acked-by: Ilya Dryomov <idryomov@gmail.com> # rbd Acked-by: Ira Weiny <ira.weiny@intel.com> # cxl Reviewed-by: Alex Shi <alexs@kernel.org> Acked-by: Iwona Winiarska <iwona.winiarska@intel.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci Acked-by: Wei Liu <wei.liu@kernel.org> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi Link: https://lore.kernel.org/r/20230313182918.1312597-23-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Linus Torvalds
|
90ddb3f034 |
pci-v6.3-changes
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmP2dbsUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzBDg//aW2IeJYku5ENXwwnCQjBlyjBGOOZ
456KGpFt/ky0N9Jp0ZS3nQSa5YN7q+L8XY48gu6I7s1hXly8iLZKLrJN++S//k55
BadXu7mDUyVoY74LYvBe0nlXuwJul2qnq9IJLufRucrn1yoyqApAh39IRdCzi4U8
mP+wad7sQA0Si4bpf80uwn6Yq8SrDoO0mtmO/dZSXJooM2t2SnDXEL/fxMwTNDA4
XsVSP9FrbPmcTLo8mkDa8Dy7JKbL6KQJF9yDlmYzuA2spQpTf+YLLfsNnmE+850h
WTtfCjVaYtlik7i9qTB+VcN1CsGVepYKK3H5the16Aeql2Fu+Ji5KSt74C220Yi9
ZSDA93d/EfGc5egKyBdUUMFgqhe46srRUAoWcMrx2T4ARGuOm5EYCa9C8C7dFmO0
j6f9MYL3j2Sw3FROEKViRVOFfbIfVW1TXIo3x0fE0ud3xkg73eKp/++X8QeTMjox
2ArY2AWPNQpUI1oMlKxlSEd5XjFf7n/hHDtFqj9bIuJzt0/8wXQf0jCYTjhpGkRB
pmO+lColK6lp+bg8aWRRkiwN73xGdQhKaeXLo0Iq4T6xr0Lb3XoskHZvt6NIGe/A
ds5/uwtErq6kCf2G9YG1xfh+G1bimbjWwsHCNfSNXzTsWGDFTCb8tvqF90m+7+yl
bllxTXA6PO312Tw=
=/y4d
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
|
||
|
Bjorn Helgaas
|
0b7af1ddcf |
Merge branch 'pci/reset'
- Always observe reset delay when waking devices from D3cold, e.g., after system sleep, regardless of whether we're allowed to runtime-suspend to D3cold (Lukas Wunner) - Unify reset and resume delays to wait for downstream devices after a bridge reset (Lukas Wunner) - Wait for downstream devices after a DPC-induced bridge reset (Lukas Wunner) * pci/reset: PCI/DPC: Await readiness of secondary bus after reset PCI: Unify delay handling for reset and resume PCI/PM: Observe reset delay irrespective of bridge_d3 |
||
|
Bjorn Helgaas
|
a7152be79b |
Revert "PCI/ASPM: Save L1 PM Substates Capability for suspend/resume"
This reverts commit |
||
Lukas Wunner
|
53b54ad074 |
PCI/DPC: Await readiness of secondary bus after reset
pci_bridge_wait_for_secondary_bus() is called after a Secondary Bus Reset, but not after a DPC-induced Hot Reset. As a result, the delays prescribed by PCIe r6.0 sec 6.6.1 are not observed and devices on the secondary bus may be accessed before they're ready. One affected device is Intel's Ponte Vecchio HPC GPU. It comprises a PCIe switch whose upstream port is not immediately ready after reset. Because its config space is restored too early, it remains in D0uninitialized, its subordinate devices remain inaccessible and DPC recovery fails with messages such as: i915 0000:8c:00.0: can't change power state from D3cold to D0 (config space inaccessible) intel_vsec 0000:8e:00.1: can't change power state from D3cold to D0 (config space inaccessible) pcieport 0000:89:02.0: AER: device recovery failed Fix it. Link: https://lore.kernel.org/r/9f5ff00e1593d8d9a4b452398b98aa14d23fca11.1673769517.git.lukas@wunner.de Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org |
||
|
Lukas Wunner
|
ac91e69805 |
PCI: Unify delay handling for reset and resume
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait for devices on the secondary bus to become accessible after reset: Although it does call pci_dev_wait(), it erroneously passes the bridge's pci_dev rather than that of a child. The bridge of course is always accessible while its secondary bus is reset, so pci_dev_wait() returns immediately. Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait() function which is called from pci_bridge_secondary_bus_reset(): https://lore.kernel.org/linux-pci/20220523171517.32407-1-windy.bi.enflame@gmail.com/ However we already have pci_bridge_wait_for_secondary_bus() which does almost exactly what we need. So far it's only called on resume from D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8). Re-using it for Secondary Bus Resets is a leaner and more rational approach than introducing a new function. That only requires a few minor tweaks: - Amend pci_bridge_wait_for_secondary_bus() to await accessibility of the first device on the secondary bus by calling pci_dev_wait() after performing the prescribed delays. pci_dev_wait() needs two parameters, a reset reason and a timeout, which callers must now pass to pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume (PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit |
||
|
Lukas Wunner
|
8ef0217227 |
PCI/PM: Observe reset delay irrespective of bridge_d3
If a PCI bridge is suspended to D3cold upon entering system sleep,
resuming it entails a Fundamental Reset per PCIe r6.0 sec 5.8.
The delay prescribed after a Fundamental Reset in PCIe r6.0 sec 6.6.1
is sought to be observed by:
pci_pm_resume_noirq()
pci_pm_bridge_power_up_actions()
pci_bridge_wait_for_secondary_bus()
However, pci_bridge_wait_for_secondary_bus() bails out if the bridge_d3
flag is not set. That flag indicates whether a bridge is allowed to
suspend to D3cold at *runtime*.
Hence *no* delay is observed on resume from system sleep if runtime
D3cold is forbidden. That doesn't make any sense, so drop the bridge_d3
check from pci_bridge_wait_for_secondary_bus().
The purpose of the bridge_d3 check was probably to avoid delays if a
bridge remained in D0 during suspend. However the sole caller of
pci_bridge_wait_for_secondary_bus(), pci_pm_bridge_power_up_actions(),
is only invoked if the previous power state was D3cold. Hence the
additional bridge_d3 check seems superfluous.
Fixes:
|
||
Huacai Chen
|
8b3517f88f |
PCI: loongson: Prevent LS7A MRRS increases
Except for isochronous-configured devices, software may set Max_Read_Request_Size (MRRS) to any value up to 4096. If a device issues a read request with size greater than the completer's Max_Payload_Size (MPS), the completer is required to break the response into multiple completions. Instead of correctly responding with multiple completions to a large read request, some LS7A Root Ports respond with a Completer Abort. To prevent this, the MRRS must be limited to an implementation-specific value. The OS cannot detect that value, so rely on BIOS to configure MRRS before booting, and quirk the Root Ports so we never set an MRRS larger than that BIOS value for any downstream device. N.B. Hot-added devices are not configured by BIOS, and they power up with MRRS = 512 bytes, so these devices will be limited to 512 bytes. If the LS7A limit is smaller, those hot-added devices may not work correctly, but per [1], hotplug is not supported with this chipset revision. [1] https://lore.kernel.org/r/073638a7-ae68-2847-ac3d-29e5e760d6af@loongson.cn [bhelgaas: commit log] Link: https://bugzilla.kernel.org/show_bug.cgi?id=216884 Link: https://lore.kernel.org/r/20230201043018.778499-3-chenhuacai@loongson.cn Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
Michael S. Tsirkin
|
98b04dd0b4 |
PCI: Fix pci_device_is_present() for VFs by checking PF
pci_device_is_present() previously didn't work for VFs because it reads the Vendor and Device ID, which are 0xffff for VFs, which looks like they aren't present. Check the PF instead. Wei Gong reported that if virtio I/O is in progress when the driver is unbound or "0" is written to /sys/.../sriov_numvfs, the virtio I/O operation hangs, which may result in output like this: task:bash state:D stack: 0 pid: 1773 ppid: 1241 flags:0x00004002 Call Trace: schedule+0x4f/0xc0 blk_mq_freeze_queue_wait+0x69/0xa0 blk_mq_freeze_queue+0x1b/0x20 blk_cleanup_queue+0x3d/0xd0 virtblk_remove+0x3c/0xb0 [virtio_blk] virtio_dev_remove+0x4b/0x80 ... device_unregister+0x1b/0x60 unregister_virtio_device+0x18/0x30 virtio_pci_remove+0x41/0x80 pci_device_remove+0x3e/0xb0 This happened because pci_device_is_present(VF) returned "false" in virtio_pci_remove(), so it called virtio_break_device(). The broken vq meant that vring_interrupt() skipped the vq.callback() that would have completed the virtio I/O operation via virtblk_done(). [bhelgaas: commit log, simplify to always use pci_physfn(), add stable tag] Link: https://lore.kernel.org/r/20221026060912.173250-1-mst@redhat.com Reported-by: Wei Gong <gongwei833x@gmail.com> Tested-by: Wei Gong <gongwei833x@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org |
||
Pali Rohár
|
c14f7ccc9f |
PCI: Assign PCI domain IDs by ida_alloc()
Replace assignment of PCI domain IDs from atomic_inc_return() to ida_alloc(). Use two IDAs, one for static domain allocations (those which are defined in device tree) and second for dynamic allocations (all other). During removal of root bus / host bridge, also release the domain ID. The released ID can be reused again, for example when dynamically loading and unloading native PCI host bridge drivers. This change also allows to mix static device tree assignment and dynamic by kernel as all static allocations are reserved in dynamic pool. [bhelgaas: set "err" if "bus->domain_nr < 0"] Link: https://lore.kernel.org/r/20220714184130.5436-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Bjorn Helgaas
|
034f93fcb1 |
Merge branch 'pci/pm'
- Cache the PTM capability offset instead of searching for it every time (Bjorn Helgaas) - Separate PTM configuration from PTM enable (Bjorn Helgaas) - Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM on suspend/resume so some Root Ports can safely enter a lower-power PM state (Bjorn Helgaas) - Disable PTM for all devices during suspend; previously we only did this for Root Ports and even then only in certain cases (Bjorn Helgaas) - Simplify pci_pm_suspend_noirq() (Rajvi Jingar) - Reduce the delay after transitions to/from D3hot by using usleep_range() instead of msleep(), which reduces the typical delay from 19ms to 10ms (Sajid Dalvi, Will McVicker) * pci/pm: PCI/PM: Reduce D3hot delay with usleep_range() PCI/PM: Simplify pci_pm_suspend_noirq() PCI/PM: Always disable PTM for all devices during suspend PCI/PTM: Consolidate PTM interface declarations PCI/PTM: Reorder functions in logical order PCI/PTM: Preserve RsvdP bits in PTM Control register PCI/PTM: Move pci_ptm_info() body into its only caller PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm() PCI/PTM: Separate configuration and enable PCI/PTM: Add pci_upstream_ptm() helper PCI/PTM: Cache PTM Capability offset |
||
Vidya Sagar
|
4ff116d0d5 |
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't saved and restored during suspend/resume leading to the L1 PM Substates configuration being lost post-resume. Save the L1 PM Substates Control Registers so that the configuration is retained post-resume. [bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr() having already done that] Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com Signed-off-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
Sajid Dalvi
|
3e347969a5 |
PCI/PM: Reduce D3hot delay with usleep_range()
PCIe r6.0, sec 5.9, requires a 10ms delay between programming a device to
change to or from D3hot and the time the device is next accessed (unless
Readiness Notifications are used).
The 10ms value (PCI_PM_D3HOT_WAIT) doesn't appear directly here because
some chipsets require 120ms for devices *below* them (pci_pm_d3hot_delay)
and some devices require more or less than 10ms (dev->d3hot_delay).
But msleep(10) typically waits about *20*ms, which is more than we need.
Switch to usleep_range() to improve the delay accuracy.
Based on a commit from Sajid in the Pixel 6 kernel tree [1]. On a Pixel 6,
the 10ms delay for the Exynos PCIe device delayed for an average of 19ms.
Switching to usleep_range() decreased the resume time by about 9ms.
[1]
|
||
|
Bjorn Helgaas
|
c01163dbd1 |
PCI/PM: Always disable PTM for all devices during suspend
We want to disable PTM on Root Ports because that allows some chips, e.g.,
Intel mobile chips since Coffee Lake, to enter a lower-power PM state.
That means we also have to disable PTM on downstream devices. PCIe r6.0,
sec 2.2.8, recommends that functions support generation of messages in
non-D0 states, so we have to assume Switch Upstream Ports or Endpoints may
send PTM Requests while in D1, D2, and D3hot. A PTM message received by a
Downstream Port (including a Root Port) with PTM disabled must be treated
as an Unsupported Request (sec 6.21.3).
PTM was previously disabled only for Root Ports, and it was disabled in
pci_prepare_to_sleep(), which is not called at all if a driver supports
legacy PM or does its own state saving.
Instead, disable PTM early in pci_pm_suspend() and pci_pm_runtime_suspend()
so we do it in all cases.
Previously PTM was disabled *after* saving device state, so the state
restore on resume automatically re-enabled it. Since we now disable PTM
*before* saving state, we must explicitly re-enable it in pci_pm_resume()
and pci_pm_runtime_resume().
Here's a sample of errors that occur when PTM is disabled only on the Root
Port. With this topology:
0000:00:1d.0 Root Port to [bus 08-71]
0000:08:00.0 Switch Upstream Port to [bus 09-71]
Kai-Heng reported errors like this:
pcieport 0000:00:1d.0: [20] UnsupReq (First)
pcieport 0000:00:1d.0: AER: TLP Header: 34000000 08000052 00000000 00000000
Decoding TLP header 0x34...... (0011 0100b) and 0x08000052:
Fmt 001b 4 DW header, no data
Type 1 0100b Msg (Local - Terminate at Receiver)
Requester ID 0x0800 Bus 08 Devfn 00.0
Message Code 0x52 0101 0010b PTM Request
The 00:1d.0 Root Port logged an Unsupported Request error when it received
a PTM Request with Requester ID 08:00.0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215453
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216210
Fixes:
|
||
|
Bjorn Helgaas
|
e8bdc5ea48 |
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
We disable PTM during suspend because that allows some Root Ports to enter
lower-power PM states, which means we also need to disable PTM for all
downstream devices. Add pci_suspend_ptm() and pci_resume_ptm() for this
purpose.
pci_enable_ptm() and pci_disable_ptm() are for drivers to use to enable or
disable PTM. They use dev->ptm_enabled to keep track of whether PTM should
be enabled.
pci_suspend_ptm() and pci_resume_ptm() are PCI core-internal functions to
temporarily disable PTM during suspend and (depending on dev->ptm_enabled)
re-enable PTM during resume.
Enable/disable/suspend/resume all use internal __pci_enable_ptm() and
__pci_disable_ptm() functions that only update the PTM Control register.
Outline:
pci_enable_ptm(struct pci_dev *dev)
{
__pci_enable_ptm(dev);
dev->ptm_enabled = 1;
pci_ptm_info(dev);
}
pci_disable_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled) {
__pci_disable_ptm(dev);
dev->ptm_enabled = 0;
}
}
pci_suspend_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_disable_ptm(dev);
}
pci_resume_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_enable_ptm(dev);
}
Nothing currently calls pci_resume_ptm(); the suspend path saves the PTM
state before disabling PTM, so the PTM state restore in the resume path
implicitly re-enables it. A future change will use pci_resume_ptm() to fix
some problems with this approach.
Link: https://lore.kernel.org/r/20220909202505.314195-5-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
||
|
Bjorn Helgaas
|
c4f36c3ab0 |
Merge branch 'pci/header-cleanup-immutable'
- Remove pci_get_legacy_ide_irq(); use ATA_PRIMARY_IRQ() and ATA_SECONDARY_IRQ() instead (Stafford Horne) - Remove isa_dma_bridge_buggy, except for x86_32, the only place it's used (Stafford Horne) - Define ARCH_GENERIC_PCI_MMAP_RESOURCE for csky (Stafford Horne) - Move common PCI definitions that arches sometimes override to asm-generic/pci.h (Stafford Horne) - Include <linux/isa-dma.h> for 'isa_dma_bridge_buggy' when needed (bisection hole here) (Randy Dunlap) * pci/header-cleanup-immutable: PCI: Stub __pci_ioport_map() for arches that don't support it at all x86/cyrix: include header linux/isa-dma.h asm-generic: Add new pci.h and use it csky: PCI: Define ARCH_GENERIC_PCI_MMAP_RESOURCE PCI: Move isa_dma_bridge_buggy out of asm/dma.h PCI: Remove pci_get_legacy_ide_irq() and asm-generic/pci.h |
||
Stafford Horne
|
abb4970ac3 |
PCI: Move isa_dma_bridge_buggy out of asm/dma.h
The isa_dma_bridge_buggy symbol is only used for x86_32, and only x86_32 platforms or quirks ever set it. Add a new linux/isa-dma.h header that #defines isa_dma_bridge_buggy to 0 except on x86_32, where we keep it as a variable, and remove all the arch- specific definitions. [bhelgaas: commit log] Suggested-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: Christoph Hellwig <hch@infradead.org> Link: https://lore.kernel.org/r/20220722214944.831438-3-shorne@gmail.com Signed-off-by: Stafford Horne <shorne@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> |
||
Kai-Heng Feng
|
08d0cc5f34 |
PCI/ASPM: Remove pcie_aspm_pm_state_change()
pcie_aspm_pm_state_change() was introduced at the inception of PCIe ASPM code, but it can cause some issues. For instance, when ASPM config is changed via sysfs, those changes won't persist across power state change because pcie_aspm_pm_state_change() overwrites them. Also, if the driver restores L1SS [1] after system resume, the restored state will also be overwritten by pcie_aspm_pm_state_change(). Remove pcie_aspm_pm_state_change(). If there's any hardware that really needs it to function, a quirk can be used instead. [1] https://lore.kernel.org/linux-pci/20220201123536.12962-1-vidyas@nvidia.com/ Link: https://lore.kernel.org/r/20220509073639.2048236-1-kai.heng.feng@canonical.com [bhelgaas: remove additional pcie_aspm_pm_state_change() call in pci_set_low_power_state(), added by |
||
|
Bjorn Helgaas
|
12068bb346 |
PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
|
||
|
Linus Torvalds
|
3cc30140db |
pci-v5.19-changes
-----BEGIN PGP SIGNATURE-----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=hEti
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Restrict E820 clipping to PCI host bridge windows (Bjorn Helgaas)
- Log E820 clipping better (Bjorn Helgaas)
- Add kernel cmdline options to enable/disable E820 clipping (Hans de
Goede)
- Disable E820 reserved region clipping for IdeaPads, Yoga, Yoga
Slip, Acer Spin 5, Clevo Barebone systems where clipping leaves no
usable address space for touchpads, Thunderbolt devices, etc (Hans
de Goede)
- Disable E820 clipping by default starting in 2023 (Hans de Goede)
PCI device hotplug:
- Include files to remove implicit dependencies (Christophe Leroy)
- Only put Root Ports in D3 if they can signal and wake from D3 so
AMD Yellow Carp doesn't miss hotplug events (Mario Limonciello)
Power management:
- Define pci_restore_standard_config() only for CONFIG_PM_SLEEP since
it's unused otherwise (Krzysztof Kozlowski)
- Power up devices completely, including anything platform firmware
needs to do, during runtime resume (Rafael J. Wysocki)
- Move pci_resume_bus() to PM callbacks so we observe the required
bridge power-up delays (Rafael J. Wysocki)
- Drop unneeded runtime_d3cold device flag (Rafael J. Wysocki)
- Split pci_raw_set_power_state() between pci_power_up() and a new
pci_set_low_power_state() (Rafael J. Wysocki)
- Set current_state to D3cold if config read returns ~0, indicating
the device is not accessible (Rafael J. Wysocki)
- Do not call pci_update_current_state() from pci_power_up() so BARs
and ASPM config are restored correctly (Rafael J. Wysocki)
- Write 0 to PMCSR in pci_power_up() in all cases (Rafael J. Wysocki)
- Split pci_power_up() to pci_set_full_power_state() to avoid some
redundant operations (Rafael J. Wysocki)
- Skip restoring BARs if device is not in D0 (Rafael J. Wysocki)
- Rearrange and clarify pci_set_power_state() (Rafael J. Wysocki)
- Remove redundant BAR restores from pci_pm_thaw_noirq() (Rafael J.
Wysocki)
Virtualization:
- Acquire device lock before config space access lock to avoid AB/BA
deadlock with sriov_numvfs_store() (Yicong Yang)
Error handling:
- Clear MULTI_ERR_COR/UNCOR_RCV bits, which a race could previously
leave permanently set (Kuppuswamy Sathyanarayanan)
Peer-to-peer DMA:
- Whitelist Intel Skylake-E Root Ports regardless of which devfn they
are (Shlomo Pongratz)
ASPM:
- Override L1 acceptable latency advertised by Intel DG2 so ASPM L1
can be enabled (Mika Westerberg)
Cadence PCIe controller driver:
- Set up device-specific register to allow PTM Responder to be
enabled by the normal architected bit (Christian Gmeiner)
- Override advertised FLR support since the controller doesn't
implement FLR correctly (Parshuram Thombare)
Cadence PCIe endpoint driver:
- Correct bitmap size for the ob_region_map of outbound window usage
(Dan Carpenter)
Freescale i.MX6 PCIe controller driver:
- Fix PERST# assertion/deassertion so we observe the required delays
before accessing device (Francesco Dolcini)
Freescale Layerscape PCIe controller driver:
- Add "big-endian" DT property (Hou Zhiqiang)
- Update SCFG DT property (Hou Zhiqiang)
- Add "aer", "pme", "intr" DT properties (Li Yang)
- Add DT compatible strings for ls1028a (Xiaowei Bao)
Intel VMD host bridge driver:
- Assign VMD IRQ domain before enumeration to avoid IOMMU interrupt
remapping errors when MSI-X remapping is disabled (Nirmal Patel)
- Revert VMD workaround that kept MSI-X remapping enabled when IOMMU
remapping was enabled (Nirmal Patel)
Marvell MVEBU PCIe controller driver:
- Add of_pci_get_slot_power_limit() to parse the
'slot-power-limit-milliwatt' DT property (Pali Rohár)
- Add mvebu support for sending Set_Slot_Power_Limit message (Pali
Rohár)
MediaTek PCIe controller driver:
- Fix refcount leak in mtk_pcie_subsys_powerup() (Miaoqian Lin)
MediaTek PCIe Gen3 controller driver:
- Reset PHY and MAC at probe time (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add chained_irq_enter()/chained_irq_exit() calls to mc_handle_msi()
and mc_handle_intx() to avoid lost interrupts (Conor Dooley)
- Fix interrupt handling race (Daire McNamara)
NVIDIA Tegra194 PCIe controller driver:
- Drop tegra194 MSI register save/restore, which is unnecessary since
the DWC core does it (Jisheng Zhang)
Qualcomm PCIe controller driver:
- Add SM8150 SoC DT binding and support (Bhupesh Sharma)
- Fix pipe clock imbalance (Johan Hovold)
- Fix runtime PM imbalance on probe errors (Johan Hovold)
- Fix PHY init imbalance on probe errors (Johan Hovold)
- Convert DT binding to YAML (Dmitry Baryshkov)
- Update DT binding to show that resets aren't required for
MSM8996/APQ8096 platforms (Dmitry Baryshkov)
- Add explicit register names per chipset in DT binding (Dmitry
Baryshkov)
- Add sc7280-specific clock and reset definitions to DT binding
(Dmitry Baryshkov)
Rockchip PCIe controller driver:
- Fix bitmap size when searching for free outbound region (Dan
Carpenter)
Rockchip DesignWare PCIe controller driver:
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property
because it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
Synopsys DesignWare PCIe controller driver:
- Return error instead of success if DMA mapping of MSI area fails
(Jiantao Zhang)
Miscellaneous:
- Change pci_set_dma_mask() documentation references to
dma_set_mask() (Alex Williamson)"
* tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (64 commits)
dt-bindings: PCI: qcom: Add schema for sc7280 chipset
dt-bindings: PCI: qcom: Specify reg-names explicitly
dt-bindings: PCI: qcom: Do not require resets on msm8996 platforms
dt-bindings: PCI: qcom: Convert to YAML
PCI: qcom: Fix unbalanced PHY init on probe errors
PCI: qcom: Fix runtime PM imbalance on probe errors
PCI: qcom: Fix pipe clock imbalance
PCI: qcom: Add SM8150 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8150 SoC
x86/PCI: Disable E820 reserved region clipping starting in 2023
x86/PCI: Disable E820 reserved region clipping via quirks
x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
PCI: microchip: Fix potential race in interrupt handling
PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
PCI: cadence: Clear FLR in device capabilities register
PCI: cadence: Allow PTM Responder to be enabled
PCI: vmd: Revert
|
||
|
Bjorn Helgaas
|
8d8b2669f9 |
Merge branch 'pci/virtualization'
- Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store() (Yicong Yang, Jay Zhou) * pci/virtualization: PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store() |
||
Yicong Yang
|
a91ee0e9fc |
PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com]
Link: https://lore.kernel.org/linux-pci/1583489997-17156-1-git-send-email-yangyicong@hisilicon.com/
Also-posted-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
||
Rafael J. Wysocki
|
3cc2a2b270 |
PCI/PM: Rearrange pci_set_power_state()
The part of pci_set_power_state() related to transitions into low-power states is unnecessary convoluted, so clearly divide it into the D3cold special case and the general case covering all of the other states. Also fix a potential issue with calling pci_bus_set_current_state() to set the current state of all devices on the subordinate bus to D3cold without checking if the power state of the parent bridge has really changed to D3cold. Link: https://lore.kernel.org/r/2139440.Mh6RI2rZIc@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> |
||
|
Rafael J. Wysocki
|
0aacdc9574 |
PCI/PM: Clean up pci_set_low_power_state()
Make the following assorted non-essential changes in
pci_set_low_power_state():
1. Drop two redundant checks from it (the caller takes care of these
conditions).
2. Change the log level of a messages printed by it to "debug",
because it only indicates a programming mistake.
Link: https://lore.kernel.org/r/2539071.Lt9SDvczpP@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
||
|
Rafael J. Wysocki
|
0ce74a3b9c |
PCI/PM: Do not restore BARs if device is not in D0
Do not attempt to restore the device's BARs in pci_set_full_power_state() if the actual current power state of the device is not D0. Link: https://lore.kernel.org/r/1849718.CQOukoFCf9@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
e200904b27 |
PCI/PM: Split pci_power_up()
One of the two callers of pci_power_up() invokes pci_update_current_state() and pci_restore_state() right after calling it, in which case running the part of it happening after the mandatory transition delays is redundant, so move that part out of it into a new function called pci_set_full_power_state() that will be invoked from pci_set_power_state() which is the other caller of pci_power_up(). Link: https://lore.kernel.org/r/1942150.usQuhbGJ8B@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
f0881d38c7 |
PCI/PM: Write 0 to PMCSR in pci_power_up() in all cases
Make pci_power_up() write 0 to the device's PCI_PM_CTRL register in order to put it into D0 regardless of the power state returned by the previous read from that register which should not matter. Link: https://lore.kernel.org/r/5748066.MhkbZ0Pkbq@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
0b59193548 |
PCI/PM: Do not call pci_update_current_state() from pci_power_up()
Notice that calling pci_update_current_state() from pci_power_up() is redundant and may be harmful in some cases. First, if the device is in a low-power state before pci_power_up() gets called for it and platform_pci_set_power_state() successfully changes its power state to D0, pci_update_current_state() will update current_state to reflect that and pci_power_up() will return success right away without restoring the device's BARs or reconfiguring ASPM which may be necessary. This is arguably incorrect and definitely inconsistent with the case when platform_pci_set_power_state() returns an error (for example, because the device is not power-manageable by the platform firmware). Second, current_state should not be overwritten until the decision whether or not to restore the device's BARs is made, because that decision generally depends on its value. Again, calling pci_update_current_state() in pci_power_up() is not consistent with this observation. Next, pci_power_up() attempts to read from the device's PCI_PM_CTRL register regardless of the current_state value unless it is PCI_D0, including the case when pci_update_current_state() sets current_state to PCI_D3cold to indicate that the device is not accessible. If the register read is not successful, current_state will be set to PCI_D3cold anyway, so that pci_update_current_state() action is redundant. Further, if pci_update_current_state() reads the device's PCI_PM_CTRL register, pci_power_up() will repeat that read going forward and it is not necessary to update current_state in the meantime. Finally, if pm_cap is not set (in which case the PCI_PM_CTRL register is not present), the power state of the device should be determined with the help of the platform firmware or set to D0 if that's not possible and pci_update_current_state() does not do that. Accordingly, rearrange pci_power_up() so as to address the above shortcomings. Link: https://lore.kernel.org/r/3695055.kQq0lBPeGt@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
6d8c016a55 |
PCI/PM: Unfold pci_platform_power_transition() in pci_power_up()
Some actions carried out by pci_platform_power_transition(() in pci_power_up() are redundant, but before dealing with them, make pci_power_up() call the pci_platform_power_transition() code directly (and avoid a redundant check when pm_cap is unset while at it). Link: https://lore.kernel.org/r/1922486.PYKUYFuaPT@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
1aa85bb14d |
PCI/PM: Set current_state to D3cold if the device is not accessible
Make pci_power_up() and pci_set_low_power_state() change current_state to PCI_D3cold when the device is not accessible along the lines of pci_update_current_state(). Link: https://lore.kernel.org/r/10104376.nUPlyArG6x@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
7957d20145 |
PCI/PM: Relocate pci_set_low_power_state()
Because pci_set_power_state() is the only caller of pci_set_low_power_state(), put the latter next to the former. No functional impact. Link: https://lore.kernel.org/r/3202976.44csPzL39Z@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
10aa5377fc |
PCI/PM: Split pci_raw_set_power_state()
The transitions from low-power states to D0 and the other way around are unnecessarily tangled in pci_raw_set_power_state() which makes it rather hard to follow. Moreover, the only caller of pci_raw_set_power_state() passing PCI_D0 as its state argument is pci_power_up(), so the code carrying out transitions into D0 can be put directly into that function. Accordingly, move the code handling transitions from low-power states into D0 directly into pci_power_up() and rename the remaining part of pci_raw_set_power_state() to pci_set_low_power_state(), because it only handles transitions into low-power state now. While at it, fix up some white space, update some comments and modify messages printed by pci_power_up() and pci_set_low_power_state() to be less confusing (which is the only expected functional impact of this change). Link: https://lore.kernel.org/r/13038676.uLZWGnKmhe@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
9c384ddd6e |
PCI/PM: Rearrange pci_update_current_state()
Save one config space access in pci_update_current_state() by testing the retrieved PCI_PM_CTRL register value against PCI_POSSIBLE_ERROR() instead of invoking pci_device_is_present() separately. While at it, drop a pair of unnecessary parens. No expected functional impact. Link: https://lore.kernel.org/r/1917095.PYKUYFuaPT@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Rafael J. Wysocki
|
8221ecd4e4 |
PCI/PM: Drop the runtime_d3cold device flag
The runtime_d3cold flag is not needed any more, so drop it. Link: https://lore.kernel.org/r/8077784.T7Z3S40VBb@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> |
||
|
Rafael J. Wysocki
|
730643d33e |
PCI/PM: Resume subordinate bus in bus type callbacks
Calling pci_resume_bus() on the secondary bus from pci_power_up() as it is done now is questionable, because it depends on the mandatory bridge power-up delays that are only covered by the PCI bus type PM callbacks. For this reason, move the subordinate bus resume to those callbacks too and use the observation that if a bridge is being powered-up during resume from system-wide suspend, it may be still desirable to runtime-resume its subordinate bus after completing the system-wide transition (in case the resume of the devices on that bus is skipped during it). Link: https://lore.kernel.org/r/3190097.aeNJFYEL58@kreacher Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> |
||
|
Rafael J. Wysocki
|
92597f97a4 |
PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by
|
||
|
Linus Torvalds
|
d0a231f01e |
pci-v5.17-changes
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
|
||
|
Bjorn Helgaas
|
f5d3ca6fff |
Merge branch 'pci/errors'
- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking for transaction errors on PCI (Naveen Naidu) - Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead of in host controller drivers, when transactions fail on PCI (Naveen Naidu) - Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads (Naveen Naidu) * pci/errors: PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors PCI: Use PCI_ERROR_RESPONSE to identify config read errors PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads PCI: rockchip-host: Drop error data fabrication when config read fails PCI: rcar-host: Drop error data fabrication when config read fails PCI: altera: Drop error data fabrication when config read fails PCI: mvebu: Drop error data fabrication when config read fails PCI: aardvark: Drop error data fabrication when config read fails PCI: kirin: Drop error data fabrication when config read fails PCI: histb: Drop error data fabrication when config read fails PCI: exynos: Drop error data fabrication when config read fails PCI: mediatek: Drop error data fabrication when config read fails PCI: iproc: Drop error data fabrication when config read fails PCI: thunder: Drop error data fabrication when config read fails PCI: Drop error data fabrication when config read fails PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices PCI: Set error response data when config read fails PCI: Add PCI_ERROR_RESPONSE and related definitions |
||
Rajat Jain
|
4353594eb0 |
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
Some devices have an erratum such that they only support DWORD accesses to some registers. E.g., this Bayhub O2 device ([VID:DID] = [0x1217:0x8621]) only supports DWORD accesses to LTR latency registers and L1 PM substates control registers: https://github.com/rajatxjain/public_shared/blob/main/OZ711LV2_appnote.pdf The L1 PM substate control registers are DWORD sized, and hence their access in the kernel is already DWORD sized, so we don't need to do anything for them. However, the LTR registers being WORD sized, are in need of a solution. Convert the WORD sized accesses to these registers into DWORD sized accesses while saving and restoring them. Link: https://lore.kernel.org/r/20211222012105.3438916-1-rajatja@google.com Signed-off-by: Rajat Jain <rajatja@google.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
Thomas Gleixner
|
3f35d2cf9f |
PCI/MSI: Decouple MSI[-X] disable from pcim_release()
The MSI core will introduce runtime allocation of MSI related data. This
data will be devres managed and has to be set up before enabling
PCI/MSI[-X]. This would introduce an ordering issue vs. pcim_release().
The setup order is:
pcim_enable_device()
devres_alloc(pcim_release...);
...
pci_irq_alloc()
msi_setup_device_data()
devres_alloc(msi_device_data_release, ...)
and once the device is released these release functions are invoked in the
opposite order:
msi_device_data_release()
...
pcim_release()
pci_disable_msi[x]()
which is obviously wrong, because pci_disable_msi[x]() requires the MSI
data to be available to tear down the MSI[-X] interrupts.
Remove the MSI[-X] teardown from pcim_release() and add an explicit action
to be installed on the attempt of enabling PCI/MSI[-X].
This allows the MSI core data allocation to be ordered correctly in a
subsequent step.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/87tuf9rdoj.ffs@tglx
|
||
Naveen Naidu
|
fa52b6447c |
PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
When config pci_ops.read() can detect failed PCI transactions, the data returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff). Obviously a successful PCI config read may *also* return that data if a config register happens to contain ~0, so it doesn't definitively indicate an error unless we know the register cannot contain ~0. Use PCI_POSSIBLE_ERROR() to check the response we get when we read data from hardware. This unifies PCI error response checking and makes error checks consistent and easier to find. Link: https://lore.kernel.org/r/f4d18d470cb90f9cb52ea155b01528ba2e76e8d6.1637243717.git.naveennaidu479@gmail.com Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> |
||
|
Linus Torvalds
|
be427a88a3 |
s390 updates for the 5.16 merge window #2
- Add PCI automatic error recovery. - Fix tape driver timer initialization broken during timers api cleanup. - Fix bogus CPU measurement counters values on CPUs offlining. - Check the validity of subchanel before reading other fields in the schib in cio code. -----BEGIN PGP SIGNATURE----- iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmGPwDMACgkQjYWKoQLX FBgCoQf/VBel0vDex9NNVo59OmGTNh9NPPT2cUU8vYEmwHfaBeInZVEx5WOxXijl 8MIbEgi6Wt3EwnIghjouC50nk8jCiNOJ8Z/wG+01zZpVpLk2GvKGjxoYxKg+5E6T sOSr7TMeKOtOp23xKAXGVIzzkrDTSyr3qruTKg/m6TFhQ0XSm/ld2k6tR5AARbuB UtsxBOtPWyHm1xPyuhjr+c6riK2vGQwJwYya4vGtIW8ix9uZoPabdqqzWsD3meBc B6fe96YQGxA8Tt80FtyJ6pHEhNDr8CE656aJZNJCnd7q1RmLWC1R/aUme+9wqQtO i9YmMvc+uzgQonpo+YgWqu9fIQqcXA== =OjW1 -----END PGP SIGNATURE----- Merge tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull more s390 updates from Vasily Gorbik: - Add PCI automatic error recovery. - Fix tape driver timer initialization broken during timers api cleanup. - Fix bogus CPU measurement counters values on CPUs offlining. - Check the validity of subchanel before reading other fields in the schib in cio code. * tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/cio: check the subchannel validity for dev_busid s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove s390/tape: fix timer initialization in tape_std_assign() s390/pci: implement minimal PCI error recovery PCI: Export pci_dev_lock() s390/pci: implement reset_slot for hotplug slot s390/pci: refresh function handle in iomap |
||
|
Linus Torvalds
|
5833291ab6 |
pci-v5.16-fixes-1
-----BEGIN PGP SIGNATURE----- iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmGNcPYUHGJoZWxnYWFz QGdvb2dsZS5jb20ACgkQWYigwDrT+vxTvQ//Wl8O7D+ckdw/4xMVi2N2uc6vCbB6 or5wmW1jfE6H7YvXbUrSMEBFoRfaz9nhuT3w9i60hzYmc9uqbsMCONBHLFAaILCP By/qkNgMFuskZGHTziqsf2Qfza04KQDv4quUl8SvlUfQeOtzUXe0vtXCrFmMTDGs QQ/bbVbI6WazTwzC11NALU3Kc8AZQXQMkd5Nt4fBfuZwFhBfnEckJgF3PmSZ7PpO N/29wJDsdkHSBNqTO1eeqdVIN8GQ6aycUYEQp3gvDCvwQ3CXtPP6SScTnqibbzjO 3wuBk+FFH8Zdq8e7CEYoj0mL2RMKhLrY1MLV8IGI1YiPy8pH1EujOiDG0uNk7YSg Zqo3NMq9L2IR28odTMc8W8oknz6CTO+rhoW22CbyImtrPT5RnWsyj1xH+k2lMxt/ 3viTV5lDzKr6V6c5xdhCP26eNzt06mlrduvQ5EvsfGu6whckyrgd6XOppExdWA/S 24N9GCJuZRCp5wgETq+Vxl48ZWLzkJ3IwoVrIhx4UTChvXPIgYrviGnEFp64ZCuc FbrINeeddxWdXkkuJ44FhmSkv7Gcl87w0cofy9tnArxZza5v3wGATFp7G1z8WO+0 HWoBhdeGGQ3+ClJUo9ihO2r9hABUbveJqxgjQbCs8P/7bR0acCoeGJCoZVj7KUUe a6GDw16Lfu87QuQ= =0aFC -----END PGP SIGNATURE----- Merge tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: "Revert conversion to struct device.driver instead of struct pci_dev.driver. The device.driver is set earlier, and using it caused the PCI core to call driver PM entry points before .probe() and after .remove(), when the driver isn't prepared. This caused NULL pointer dereferences in i2c_designware_pci and probably other driver issues" * tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: Revert "PCI: Use to_pci_driver() instead of pci_dev->driver" Revert "PCI: Remove struct pci_dev->driver" |
||
|
Bjorn Helgaas
|
e0217c5ba1 |
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
This reverts commit |
||
|
Linus Torvalds
|
dd72945c43 |
cxl for v5.16
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up open
coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs. 'cxl_test'
is a module built from tools/testing/cxl/ that mocks up a CXL topology
to augment the nascent support for emulation of CXL devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver and
core-infrastructure buckets. For example, mailbox handling is now a
generic core capability consumed by the PCI and cxl_test drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYYRtyQAKCRDfioYZHlFs
Z7UsAP9DzUN6IWWnYk1R95YXYVxFriRtRsBjujAqTg49EMghawEAoHaA9lxO3Hho
l25TLYUOmB/zFTlUbe6YQptMJZ5YLwY=
=im9j
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl updates from Dan Williams:
"More preparation and plumbing work in the CXL subsystem.
From an end user perspective the highlight here is lighting up the CXL
Persistent Memory related commands (label read / write) with the
generic ioctl() front-end in LIBNVDIMM.
Otherwise, the ability to instantiate new persistent and volatile
memory regions is still on track for v5.17.
Summary:
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up
open coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs.
'cxl_test' is a module built from tools/testing/cxl/ that mocks up
a CXL topology to augment the nascent support for emulation of CXL
devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver
and core-infrastructure buckets. For example, mailbox handling is
now a generic core capability consumed by the PCI and cxl_test
drivers"
* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
ocxl: Use pci core's DVSEC functionality
cxl/pci: Use pci core's DVSEC functionality
PCI: Add pci_find_dvsec_capability to find designated VSEC
cxl/pci: Split cxl_pci_setup_regs()
cxl/pci: Add @base to cxl_register_map
cxl/pci: Make more use of cxl_register_map
cxl/pci: Remove pci request/release regions
cxl/pci: Fix NULL vs ERR_PTR confusion
cxl/pci: Remove dev_dbg for unknown register blocks
cxl/pci: Convert register block identifiers to an enum
cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
cxl/pci: Disambiguate cxl_pci further from cxl_mem
Documentation/cxl: Add bus internal docs
cxl/core: Split decoder setup into alloc + add
tools/testing/cxl: Introduce a mock memory device + driver
cxl/mbox: Move command definitions to common location
cxl/bus: Populate the target list at decoder create
tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
cxl/pmem: Add support for multiple nvdimm-bridge objects
cxl/pmem: Translate NVDIMM label commands to CXL label commands
...
|
||
Niklas Schnelle
|
dfd5bb23ad |
PCI: Export pci_dev_lock()
Commit
|