IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch adds support for TI's CPSW driver.
The three port switch gigabit ethernet subsystem provides ethernet packet
communication and can be configured as an ethernet switch. Supports
10/100/1000 Mbps.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPSW ethernet switch has a built-in address lookup engine. This patch adds
the code necessary for programming this module.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent race condition between commands on comm channel.
Happened while unloading the driver when switching from
event to polling mode. VF got completion on the last command
before switching to polling mode, but toggle was not changed.
After the fix - VF will not write the next command before
toggle is updated.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.
eth0--
|-- bond0 -- br0
eth1--
modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1
brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0
Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.
The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.
If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.
Instead I choose to modify bonding to send igmp report for its master.
Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for MPC5125 FEC. The FEC on MPC5125 additionally
supports RMII PHY interface. Configure controller/PHY interface type
according to the optional phy-connection-type property in the ethernet
node. This property should be either "rmii" or "mii".
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug when using 'ethtool -K ethx tx off' to turn off tx ip checksum,
FCoE CRC offload should not be impacte. The skb_checksum_help() is needed
only if it's not FCoE traffic for ip checksum, regardless of ethtool toggling
the tx ip checksum on or off. Instead of using CHECKSUM_PARTIAL, we will
use CHECKSUM_UNNECESSARY as a proper indication to avoid sw ip checksum
on FCoE frames.
Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows us to avoid a Tx hang when SR-IOV is enabled. This hang
can be triggered by sending small packets at a rate that was triggering Rx
missed errors from the adapter while the internal Tx switch and at least
one VF are enabled.
This was all due to the fact that under heavy stress the Rx FIFO never
drained below the flow control high water mark. This resulted in the Tx
FIFO being head of line blocked due to the fact that it relies on the flow
control high water mark to determine when it is acceptable for the Tx to
place a packet in the Rx FIFO.
The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so
that even if the ring is almost completely full we can still place Tx
packets on the Rx ring and drop incoming Rx traffic if we do not have
sufficient space available in the Rx FIFO.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of dropping the packet, we keep the skb buffer, and return
NETDEV_TX_BUSY to let upper layer retry send. This will not cause
endless loop, because the host is taking data away from ring buffer,
and we have called the stop_queue before returning NETDEV_TX_BUSY.
The stop_queue was called in the function netvsc_send() in file
netvsc.c, then it returns to rndis_filter_send(), which returns to
netvsc_start_xmit() in file netvsc_drv.c. So the NETDEV_TX_BUSY is
indeed returned AFTER queue is stopped.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve namespace issues when FCoE or DCB is not enabled.
The issue is with certain configurations we end up with namespace
problems. A simple example:
ixgbe_main.c
- defines func A()
- uses func A()
ixgbe_fcoe.c
- uses func A()
ixgbe.h
- has prototype for func A()
For default (FCoE included) all is good. But when it isn't the namespace
checker complains about how func A() could be static.
To resolve this, created a ixgbe_lib file to contain functions used
by DCB/FCoE and their helper functions so that they are always in
namespace whether or not DCB/FCoE is enabled.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Remove an unnecessary #define and use memcpy
instead of a loop to copy an ethernet address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need for yet another #define for this.
Convert NODE_ADDRESS_SIZE use to ETH_ALEN and remove #define.
Use memcpy instead of a loop to copy an address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously applied patch making the bnx2x statistics consistent
did not apply to old FWs. This remedies it, extending the consistent
behaviour to all drivers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes changes in macros to better distinguish between the two
protocols, and slightly changed the way their macs are set.
Notice this file contains string print lines with more than 80 characters,
as to not break prints.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new error flags are supported by the bnx2x FW.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes were mostly made to enable back-to-back data flow with dcb.
Other changes were simply deemed as a better 'clean' initial configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces sparse warnings in the bnx2x code,
mostly by changing functions into static and changing
initialization of structures.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've revised driver prints, changing the mask of existing prints
to allow better control over the debug messages, added prints to
error scenarios, removed unnecessary prints and corrected some spelling.
Please note that this patch contains lines with over 80 characters,
as string messages were kept in a single line.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flex10 mode the number of vlan slots supported is halved.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the variable name data with the variable name features
for ixgbe_fix_features and ixgbe_set_features. This helps to make some
issues more obvious such as the fact that we were disabling Rx VLAN tag
stripping when we should have been forcing it to be enabled when DCB is
enabled.
In addition there was deprecated code present that was disabling the LRO
flag if we had the itr value set too low. I have updated this logic so
that we will now allow the LRO flag to be set, but will not enable RSC
until the rx-usecs value is high enough to allow enough time for Rx packet
coalescing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
use the new ability to override the voltage set and get operations to
support the in-CPU voltage management. The other changes are minor
fixes, the addition of a few new regulators and device tree support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EHNp
-----END PGP SIGNATURE-----
Merge tag 'topic/twl' into regulator-next
TWL specific changes, cross-merged with OMAP due to arch/arm wanting to
use the new ability to override the voltage set and get operations to
support the in-CPU voltage management. The other changes are minor
fixes, the addition of a few new regulators and device tree support.
Fix the following section warnings :
WARNING: vmlinux.o(.text+0x49dbc): Section mismatch in reference
from the function acpi_map_cpu2node() to the variable
.cpuinit.data:__apicid_to_node The function acpi_map_cpu2node()
references the variable __cpuinitdata __apicid_to_node. This is
often because acpi_map_cpu2node lacks a __cpuinitdata
annotation or the annotation of __apicid_to_node is wrong.
WARNING: vmlinux.o(.text+0x49dc1): Section mismatch in reference
from the function acpi_map_cpu2node() to the function
.cpuinit.text:numa_set_node() The function acpi_map_cpu2node()
references the function __cpuinit numa_set_node(). This is often
because acpi_map_cpu2node lacks a __cpuinit annotation or the
annotation of numa_set_node is wrong.
WARNING: vmlinux.o(.text+0x526e77): Section mismatch in
reference from the function prealloc_protection_domains() to the
function .init.text:alloc_passthrough_domain() The function
prealloc_protection_domains() references the function __init
alloc_passthrough_domain(). This is often because
prealloc_protection_domains lacks a __init annotation or the annotation of alloc_passthrough_domain is wrong.
Signed-off-by: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1331810188-24785-1-git-send-email-sp@numascale.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Power domains that were off before hibernation shouldn't be turned on
during device restore, so prevent that from happening.
This change fixes up commit 65533bbf63b4f37723fdfedc73d0653958973323
PM / Domains: Fix hibernation restore of devices, v2
that didn't include it by mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds support for enabling or disabling UDP RSS via the
ethtool -N rx-flow-hash command.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains several fixes for formatting in regards to whitespace.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes two minor issues. The first was the fact that we were
setting the return value to false twice in the set_rss_queues function.
The second is the fact that we should have been using "min_t(int," instead
of "min((int)" in set_fdir_queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The err_eeprom and err_sw_init tags both go to the same location. So
instead of maintaining two tags this patch combines them so we only use
err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change relocates the ixgbe_poll routine so it is right next to the
interrupt routine that schedules and calls it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change just cleans up some of the logic in the service_timer function
so that we can avoid unnecessary swapping of the ready value between true to
false and back to true.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that only the 2nd cache line in the ring structure
should see frequent updates. The advantage to this is that it should
reduce the amount of cross CPU cache bouncing since only the 2nd cache line
will be changing between most network transactions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we store the tx_flags and protocol information
to the tx_buffer_info structure sooner. This allows us to avoid unnecessary
read/write transactions since we are placing the data in the final location
earlier.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If there are no unacked bad blocks, then there is no point searching
for them to acknowledge them.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In super_1_sync (the first hunk) we need to clear 'changed' before
checking read_seqretry(), otherwise we might race with other code
adding a bad block and so won't retry later.
In md_update_sb (the second hunk), in the case where there is no
metadata (neither persistent nor external), we treat any bad blocks as
an error. However we need to clear the 'changed' flag before calling
md_ack_all_badblocks, else it won't do anything.
This patch is suitable for -stable release 3.0 and later.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Be redefining ->chunkshift as the shift from sectors to chunks rather
than bytes to chunks, we can just use "bitmap->chunkshift" which is
shorter than the macro call, and less indirect.
Signed-off-by: NeilBrown <neilb@suse.de>
These funcitons don't add anything useful except possibly the trace
points, and I don't think they are worth the extra indirection.
So remove them.
Signed-off-by: NeilBrown <neilb@suse.de>
There is nothing gained by holding a lock while we check if a pointer
is NULL or not. If there could be a race, then it could become NULL
immediately after the unlock - but there is no race here.
So just remove the locking.
Signed-off-by: NeilBrown <neilb@suse.de>
The use of a goto makes the control flow more obscure here.
So make it a normal:
if (x) {
Y;
}
No functional change.
Signed-off-by: NeilBrown <neilb@suse.de>
