IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch fixes hci_remote_name_evt dose not resolve name during
discovery status is RESOLVING. Before simultaneous dual mode scan enabled,
hci_check_pending_name will set discovery status to STOPPED eventually.
Signed-off-by: Wesley Kuo <wesley.kuo@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most likely, the shutdown routine requires the interface to be up.
This is the case for BTUSB_INTEL: the routine tries to send a command
to the interface, but since this one is down, it fails and exits once
HCI_INIT_TIMEOUT has expired.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0.x
While it is not used by newer userspace anymore, the older userspace was
utilizing HIDP_VIRTUAL_CABLE_UNPLUG and HIDP_BOOT_PROTOCOL_MODE flags
when adding a new HIDP connection.
The flags validation is important, but we can not break older userspace
and with that allow providing these flags even if newer userspace does
not use them anymore.
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When establishing a Bluetooth LE connection, read the remote used
features mask to determine which features are supported. This was
not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and
also 4.2 have introduced new optional features, this becomes more
important.
This works the same as with BR/EDR where the connection enters the
BT_CONFIG stage and hci_connect_cfm call is delayed until the remote
features have been retrieved. Only after successfully receiving the
remote features, the connection enters the BT_CONNECTED state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Read Local Out Of Band Extended Data mgmt command is specified to
return the SSP values when given a BR/EDR address type as input
parameter. The returned values may include either the 192-bit variants
of C and R, or their 256-bit variants, or both, depending on the status
of Secure Connections and Secure Connections Only modes. If SSP is not
enabled the command will only return the Class of Device value (like it
has done so far).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_recv_stream_fragment function should have never been introduced
in the first place. The Bluetooth core does not need to know anything
about the HCI transport protocol.
With all transport protocol specific detailed moved back into the
drivers where they belong (mainly generic USB and UART drivers), this
function can now be removed.
This reduces the size of hci_dev structure and also removes an exported
symbol from the Bluetooth core module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The data pointer provided to hci_recv_stream_fragment function should
have been marked const. The function has no business in modifying the
original data. So fix this now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The TX power field in the LE advertising data should be placed last
since it needs to be possible to enable kernel controlled TX power,
but still allow for userspace provided flags field.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With this patch kernel will be able to handle setup request. This is
needed if we would like to handle control mesages with extension
headers. User space will be only resposible for reading setup data and
checking if scenario is conformance to specification (dst and src device
bnep role). In case of new user space, setup data must be leaved(peek
msg) on queue. New bnep session will be responsible for handling this
data.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Handling extended headers of control frames is required BNEP
functionality. This patch refractor bnep rx frame handling function.
Extended header for control frames shouldn't be omitted as it was
previously done. Every control frame should be checked if it contains
extended header and then every extension should be parsed separately.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is needed if user space wants to know supported bnep features
by kernel, e.g. if kernel supports sending response to bnep setup
control message. By now there is no possibility to know supported
features by kernel in case of bnep. Ioctls allows only to add connection,
delete connection, get connection list, get connection info. Adding
connection if it's possible (establishing network device connection) is
equivalent to starting bnep session. Bnep session handles data queue of
transmit, receive messages over bnep channel. It means that if we add
connection the received/transmitted data will be parsed immediately. In
case of get bnep features we want to know before session start, if we
should leave setup data on socket queue and let kernel to handle with it,
or in case of no setup handling support, if we should pull this message
and handle setup response within user space.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Send command not understood response should be verified if it was
successfully sent, like all send responses.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LE pivacy feature is used, then pairing has to happen based
on resolvable random addresses (RPA), but currently there is no clean
way to retrieve the correct RPA. So instead of returning an outdated
RPA, just disallow this command when LE privacy is in use.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that there's a HCI request API available where the callback receives
the resulting skb, we can convert the local OOB data reading to use this
new API. This patch does the necessary update in mgmt.c (which also
requires moving the callback higher up since it's now a static function)
and removes the custom calls from hci_event.c that are no-longer
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the hci_req_run_skb() API consistent with hci_cmd_sync_ev()
the callback should receive the cmd_complete parameters in the 'normal'
case and the full HCI event if a special event was expected. This patch
moves the hci_get_cmd_complete() function from hci_core.c to hci_event.c
where it's used to strip the skb from the needed headers before passing
it on to the callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_pending() function has no users anymore, so simply remove
it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the synchronous HCI requests use the new API and a new private
variable the recv_evt member of hci_dev is no-longer needed. This patch
removes it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there's an API in place that allows passing the resulting skb
to the request callback we can conveniently convert the hci_req_sync and
related functions to use it. Since we still need to get the skb from the
async callback into the sleeping _sync() function the patch adds another
req_skb variable to hci_dev where the sync request state is tracked.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a second possible callback for HCI requests where the
callback will receive the full skb of the last successfully completed
HCI command. This API is useful for cases where we want to use a request
to read some data and the existing hci_event.c handlers do not store it
e.g. in the hci_dev struct.
The reason the patch is a bit bigger than just adding the new API is
because the hci_req_cmd_complete() functions required some refactoring
to enable it: now hci_req_cmd_complete() is simply used to request the
callback pointers if any, and the actual calling of them happens from a
single place at the end of hci_event_packet(). The reason for this is
that we need to pass the original skb (without any skb_pull, etc
modifications done to it) and it's simplest to keep track of it within
the hci_event_packet() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When dealing with HCI command status events, the reasoning for trying to
mark a request as complete if no specific event is being waited for and
status was success is not self-evident. This patch adds a clarifying
comment above the if-statement.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When SMP selftest is enabled, then besides printing the result into the
kernel message buffer, also create a debugfs file that allows retrieving
the same information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When ECDH selftest is enabled, then besides printing the result into the
kernel message buffer, also create a debugfs file that allows retrieving
the same information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BNEP flags should be clearly restricted to valid ones. So this puts
extra checks in place to ensure this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HIDP flags should be clearly restricted to valid ones. So this puts
extra checks in place to ensure this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The CMTP flags should be clearly restricted to valid ones. So this puts
extra checks in place to ensure this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes it is good to be able to read the current
configured Device ID details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to shrink the size of bt_skb_cb, this patch moves the HCI
request related variables into their own req_ctrl struct. Additionall
the L2CAP and HCI request structs are placed inside the same union since
they will never be used at the same time for the same skb.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're getting very close to the maximum possible size of bt_skb_cb. To
prepare to shrink the struct with the help of a union this patch moves
all L2CAP related variables into the l2cap_ctrl struct. To later add
other 'ctrl' structs the L2CAP one is renamed simple 'l2cap' instead
of 'control'.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Local OOB Extended Data commands are required to return the
address type and the data length at least. However currently the error
returns only the address type.
To fix this and avoid any extra allocations or stack memory, rearrange
the code so that the same path can be used for error returns.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Taking the hci_dev lock for just a memory allocation seems a bit too
much and not really needed. So instead try to allocate the memory first
and then take the lock.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes a bug where the advertising parameters weren't updated
after a call to "Set Connectable" if the HCI_ADVERTISING_INSTANCE
setting was set.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this patch, ADV_SCAN_IND will be used for advertising instances
that have non-zero scan response data while the global "connectable"
setting is "off".
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a bug where ADV_NONCONN_IND was being used for
advertising instances >0 while the global connectable setting was
set to "on".
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the HCI init phase a completed request might be the last part of
the setup procedure after which the actual init procedure starts. The
init procedure begins with a call to hci_reset_req() which sets the
HCI_RESET flag. The purpose of this flag is to make us ignore any
updates to ncmd/cmd_cnt as long as we haven't received the command
complete event for the HCI_Reset. There's a potential race with this
however:
hci_req_cmd_complete(hdev, opcode, status);
if (ev->ncmd && !test_bit(HCI_RESET, &hdev->flags)) {
atomic_set(&hdev->cmd_cnt, 1);
if (!skb_queue_empty(&hdev->cmd_q))
queue_work(hdev->workqueue, &hdev->cmd_work);
}
Since the hci_req_cmd_complete() will trigger the completion of the
setup stage, it's possible that hci_reset_req() gets called before we
try to read ev->ncmd and the HCI_RESET flag. Because of this the cmd_cnt
would never be updated and the hci_reset_req() in practice ends up
blocking itself.
This patch fixes the issue by updating cmd_cnt before notifying the
request completion, and then reading it again to determine whether the
cmd_work should be queued or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch simplifies the code paths for assembling the advertising data
used by advertising instances 0 and 1.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the "supported_flags" parameter returned from the
"Read Advertising Features" command. Add Advertising will now return
an error if an unsupported flag is provided.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the "tx-power" flag of the Add
Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the "managed-flags" flag of the Add
Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the "limited-discoverable" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the "discoverable" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the "connectable mode" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the user of the management interface is not trusted, then it only
has access to a limited set of commands and events. When providing the
list of supported commands and events take the trusted vs untrusted
status of the user into account and return different lists.
This way the untrusted user knows exactly which commands it can
execute and which events it can receive. So no guesswork needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements support for the timeout parameter of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements setting the Scan Response data provided as part
of an advertising instance through the Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the most basic implementation for the
"Add Advertisement" command. All state updates between the
various HCI settings (POWERED, ADVERTISING, ADVERTISING_INSTANCE,
and LE_ENABLED) has been implemented. The command currently
supports only setting the advertising data fields, with no flags
and no scan response data.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
