IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
CCS supports three variants of PHY timing control, auto, UI based and
manual. The driver previously assumed UI based control that requires
updating the link rate to the sensor. Now default to automatic control
instead, and only write the link rate to the sensor in UI mode.
If neither auto or UI control is supported, return an error in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver depends on the external clock frequency. Add a sanity check for
the frequency, by returning an error from probe if it's zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A CCS compliant device requires a delay before the first I²C transaction
after pulling xshutdown up or starting the external clock. This is what
the driver does. However, if neither is actually there, there's no need
for the delay.
This also has the effect of removing an unnecessary delay on ACPI systems
where ACPI is responsible for the power-up sequence.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Verify the software reset has been completed until proceeding.
The spec does not guarantee a delay but presumably 100 ms should be
enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver always used software reset after the sensor's power sequence
that includes a hardware reset if we have a reset GPIO. Do not use
software reset if we just brought the sensor up from hardware reset state.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor's address was changed before resetting and changing the
address again. Don't do it before reset as it's useless.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Get the first endpoint from port 0 instead of the next one, whatever it
might be. There are no other ports so there's no functional change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2 controls for controlling CCS lens shading correction as well as
conveying its capabilities.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Also print out MSR registers written to the sensor. This isn't entirely
optimal as the debug strings are produced even if they're not used but
that isn't really a grave issue --- the I²C bus is very slow anyway.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS spec defines an alternative implementation for global analogue
gain. Add support for that in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add two new controls for alternative analogue gain some CCS compliant
camera sensors support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add four controls for reading CCS analogue gain coefficients. The
values are constants that are device specific.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2 controls for analogue gain constants required to control
analogue gain. The values are device specific and thus need to be obtained
from the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add user documentation for the CCS driver. This includes e.g. sub-devices
implemented by the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a control base for CCS controls, and reserve 128 controls. Luckily
these numbers are cheap.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some devices do not implement analogue gain this way. Only add the control
when a device does have the support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The analogue gain control was stored to the device specific struct but was
never used. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SMIA only has per-component digital gain. Add support for it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS supports global (all-component) digital gain. Add support for it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drivers don't need to explicitly call devm_{}_put on driver
removal, as it's automatically called by the device driver
resource management code.
Fixes: aab7ed1c3927 ("media: i2c: Add driver for Aptina MT9V111")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV8865 is a 8 Mpx CMOS image sensor producing 3264x2448 at 30 fps.
Other modes (including some with sub-sampling) are available too.
It outputs 10-bit bayer CFA data through a MIPI CSI-2 interface with
up to 4 lanes supported.
Some register initialisation sequences are still needed for this driver,
as they cover registers for which no documentation is available.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version is a rewrite of the first version that matches the structure
of the OV5648 driver, with explicit PLL configuration, all the necessary
mode-specific fields, associatied registers and reduced static sequences.
It was tested with the Banana Pi Camera Board v3 and the Banana Pi M3.
Co-developed-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5648 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2
in a one or two lane configuration.
Most of the features of the hardware are supported, including:
- Auto and manual exposition/gain
- Auto and manual white balance
- Horizontal and vertical flip
- Test patterns
But the following are still missing:
- Debanding, based on power source frequency;
- Exposition setting correlated to time units.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This introduces YAML bindings documentation for the OV5648
image sensor.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Loop was useless as it would always exit on the first iteration. Fix
it with right condition.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Fixes: a86cf9b29e8b ("media: ipu3-cio2: Validate mbus format in setting subdev format")
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.16 and up
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver currently reports a single supported value for
V4L2_CID_PIXEL_RATE and initializes the control's minimum value to 0,
which is very risky, as userspace might accidentally use it as divider
when calculating the time duration of a line.
Fix this by using as minimum the only supported value when registering
the control.
Fixes: 5de35c9b8dcd1 ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document pratices of handling clocks in camera sensor drivers on both DT
and ACPI.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to the original code in the driver it was never assumed to work
with big page sizes: unsigned short type followed by PAGE_SHIFT and
PAGE_MASK which may be different on non-x86 architectures.
Recently LKP found an issue on non-x86 architectures due to above
mentioned limitations. Since Sakari acknowledges that it's not really
useful to be able to compile this elsewhere, mark it x86 only.
Fixes: a31d19f88932 ("media: ipu3: allow building it with COMPILE_TEST on non-x86 archs")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
kvmalloc() was used to allocate the temporary memory buffer that was used
to contain both the IOCTL argument as well as a possible array argument
that could have been large. Now that the two are separated, the IOCTL
argument is known to be small in size. Use kmalloc to allocate it instead
of kvmalloc. Similarly for releasing it.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When an IOCTL with argument size larger than 128 that also used array
arguments were handled, two memory allocations were made but alas, only
the latter one of them was released. This happened because there was only
a single local variable to hold such a temporary allocation.
Fix this by adding separate variables to hold the pointers to the
temporary allocations.
Reported-by: Arnd Bergmann <arnd@kernel.org>
Reported-by: syzbot+1115e79c8df6472c612b@syzkaller.appspotmail.com
Fixes: d14e6d76ebf7 ("[media] v4l: Add multi-planar ioctl handling code")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add and document a media entity type for Image Signal Processor devices.
Surprisingly we didn't have one, so add one now. More or less all ISP
drivers should use this type instead of what they currently are using (or
not using anything).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document that v4l2_async_notifier_parse_fwnode_endpoints() is deprecated.
Its functionality has been replaced by other, better functions. Also add a
reference to an example if someone ends up wandering here.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Update the formula to calculate the pixel rate on the link for C-PHY.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Capturing in 640x480 SBGGR8_1X8 hangs the system when capturing
with the unicam driver on RaspberryPi 4 platform.
Remove it and remove the support for multiple media bus codes in
the driver.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver reports the V4L2_SUBDEV_FL_HAS_EVENTS flag but does not
support subscribing and unsubscribing to events.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the two register-value lists const.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use pm_runtime_get_if_in_use() in s_ctrl to apply controls
only when the device is powered on.
Rework the control set function to balance the
pm_runtime_get_if_in_use() call with
pm_runtime_put() at the end of the function.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the s_stream() operation to turn the sensor on and
off at stream enable/disable time using the pm_runtime infrastructure.
Protect the stream on/off from being called multiple times in
sequence with a 'streaming' flag.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the pm_runtime framework to replace the legacy s_power() operation.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure is clipped by the VTS of the mode, so it needs to be updated
when this is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the V4L2_CID_HBLANK read-only control.
The implementation has been upported from RaspberryPi BSP commit:
commit d82f202156605 ("media: i2c: ov5647: Set V4L2_SUBDEV_FL_HAS_EVENTS flag")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clients need to know the pixel rate in order to compute exposure
and frame rate values. Advertise it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov5647 subdev can generate control events, therefore set
the V4L2_SUBDEV_FL_HAS_EVENTS flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that the driver supports more than a single mode, implement the
.set_fmt pad operation and adjust the existing .get_fmt one to report
the currently applied format.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SBGGR10_1X10 formats support more resolutions than SBGGR8_1X8.
Make it the default sensor format and set 2x2 binned 640x480 resolution
as default sensor size as it maximizes the FOV and framerate.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Before adding new modes, rename the only existing one to report
the bit depth to distinguish it from future additions.
While at it, briefly describe the mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support the get_selection() pad operation to report the device
full pixel array size, the currently applied analogue crop rectangle and
the active pixel array dimensions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
