IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 0b884fe71f9ee6a5df35e677154256ea2099ebb8 upstream.
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3dee7a279ebe4d892b359fe3696938ec15 upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f70a876c2e78e58c5ca0bbf0547e4f6d upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e6fe59ede155881a622f5901551b1cc8748f6a upstream.
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e4f0b85be308a01b830c5fbdffc657e1a6dd0 upstream.
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf30 ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8058d69905058ec8f467a120b5ec5bb831ea67f3 ]
Commit 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f5b3f433641c543ebe5171285a42aa6adcdb2d22 upstream.
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af466 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1334d3b4e49e35d8912a7c37ffca4c5afb9a0516 upstream.
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28683e847e2f20eed22cdd24f185d7783db396d3 upstream.
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 845b89127bc5458d0152a4d63f165c62a22fcb70 upstream.
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
[iwamatsu: Use DPM_FLAG_NEVER_SKIP instead of DPM_FLAG_NO_DIRECT_COMPLETE]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bd970aa62f2f7f80fd0d212b1d4ccea5df4aed ]
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21653a4181ff292480599dad996a2b759ccf050f ]
Some ACPI i2c-devices _STA method (which is used to detect if the device
is present) use autodetection code which probes which device is present
over i2c. This requires the I2C ACPI OpRegion handler to be registered
before we enumerate i2c-clients under the i2c-adapter.
This fixes the i2c touchpad on the Lenovo ThinkBook 14-IIL and
ThinkBook 15 IIL not getting an i2c-client instantiated and thus not
working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1842039
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 66d402e2e9455cf0213c42b97f22a0493372d7cc upstream.
On suspend the original host configuration gets restored. The
resume routine has to undo this, otherwise the SMBus master
may be left in disabled state or in i2c mode.
[JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.]
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a355aeb24081e4538d4d424cd189f16c0bbd983 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 914a7b3563b8fb92f976619bbd0fa3a4a708baae ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c9e914f9a0478fba4dc6f227cfd69cf84a4063 ]
Due to the lockless design of the driver, it is theoretically possible
to access a NULL pointer, if a slave interrupt was running while we were
unregistering the slave. To make this rock solid, disable the interrupt
for a short time while we are clearing the interrupt_enable register.
This patch is purely based on code inspection. The OOPS is super-hard to
trigger because clearing SAR (the address) makes interrupts even more
unlikely to happen as well. While here, reinit SCR to SDBS because this
bit should always be set according to documentation. There is no effect,
though, because the interface is disabled.
Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314139f9f0abdba61ed9a8463bbcb0bf900ac5a2 ]
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db9254d6b896b587759e2c844c277fb1a6da5b9 ]
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb01597158ffb1853a7a7fc2c57d4c844640f75e ]
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 597911287fcd13c3a4b4aa3e0a52b33d431e0a8e ]
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.
Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michael Shych <michaelsh@mellanox.com>
Tested-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd217f2300793a106b49c7dfcbfb26e348bc7593 ]
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40e05200593af06633f64ab0effff052eee6f076 ]
If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of
them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued
on some random device to return an arbitrary value in the first
byte (and nothing else). When this happens, i2c_smbus_xfer_emulated()
will happily write past the end of the supplied data buffer, thus
causing Bad Things to happen. To prevent this, check the size
before copying the data block and return an error if it is too large.
Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C")
Signed-off-by: Mans Rullgard <mans@mansr.com>
[wsa: use better errno]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 502035e284cc7e9efef22b01771d822d49698ab9 ]
The port number field in the status register was not correct, so fix it.
Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67d4530cdade7ebfafa2c6b46f2a0dad3e41bcb ]
Tegra194 supports maximum 64K Bytes transfer per packet.
Tegra186 and prior supports maximum 4K Bytes transfer per packet.
This patch fixes this payload difference between Tegra194 and prior
Tegra chipsets using separate i2c_adapter_quirks.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0604ee4aefa20f493a32dc223599f922fb615367 ]
Not all fields were properly documented. Add kerneldoc for the missing
fields to prevent the build from flagging them.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c990bbafdb11c608bba2d529f72ded9bdff88678 ]
Some of the kerneldoc uses a strange spelling for abbreviations. Turn
them into all-uppercase and clean up some whitespace issues while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ]
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ]
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ]
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ce26a1c31ca928df4dfc7504c8898b71ff9f5d5 ]
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d4c7977499a736f3f80826bdc9744344ad55589 ]
Use a mutex to protect access to idev->msg_len, idev->buf, etc. which
are modified by both altr_i2c_xfer_msg() and altr_i2c_isr().
This is the minimal fix for easy backporting. A cleanup to remove the
spinlock will be added later.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9d1a0a41d4486955e96552293c1fcf1fce61602 ]
A call to 'i2c_demux_deactivate_master()' is missing in the error handling
path, as already done in the remove function.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1413ef638abae4ab5621901cf4d8ef08a4a48ba6 upstream.
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7fda ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7fda to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edb2c9dd3948738ef030c32b948543e84f4d3f81 upstream.
device_property_read_u32() returns errno or 0, so we should use the
integer variable 'ret' and not the u32 'val' to hold the retval.
Fixes: 0560ad576268 ("i2c: altera: Add Altera I2C Controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1b9f99ff8c40bba6e59de9ad4a659447b1e4112 upstream.
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8daee952b4389729358665fb91949460641659d4 upstream.
i2c_verify_client() can fail, so we need to put the device when that
happens.
Fixes: 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure notifications")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3747cd2efe7ecb9604972285ab3f60c96cb753a8 upstream.
If a GPIO we are trying to use is not available and we are deferring
the probe, don't output an error message.
This seems to have been the intent of commit 05c74778858d
("i2c: gpio: Add support for named gpios in DT") but the error was
still output due to not checking the updated 'retdesc'.
Fixes: 05c74778858d ("i2c: gpio: Add support for named gpios in DT")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e661cedcc0a072d91a32cb88e0515ea26e35711 upstream.
The printout for txabrt is way too talkative and is highly annoying with
scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest
can be gained by I2C core debugging and datasheet information. Also,
make it a debug printout, it won't help the regular user.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54498e8070e19e74498a72c7331348143e7e1f8c upstream.
Factor out 100 from the equation and do 32-bit arithmetic (3 * clk_mhz / 10)
instead of 64-bit.
Notice that clk_mhz is MHz, so the multiplication will never wrap 32 bits
and there is no need for div_u64().
Addresses-Coverity: 1458369 ("Unintentional integer overflow")
Fixes: 0560ad576268 ("i2c: altera: Add Altera I2C Controller driver")
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d77eceb2de99f5d7e0c645bad15511fe1af59e09 ]
Distinguish between the case where dma information is not provided
within the DT and the case of an error during the dma init.
Exit the probe with error in case of an error during dma init.
Fixes: bb8822cbbc53 ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7787657d7ee55a9ecf4aea4907b46b87a44eda67 upstream.
Fix a typo in the free slave id search loop. Instead of I2C_CLIENT_PEC,
it should have been I2C_CLIENT_TEN. The slave id 1 can only handle 7-bit
addresses and thus is not eligible in case of 10-bit addresses.
As a matter of fact none of the slave id support I2C_CLIENT_PEC, overall
check is performed at the beginning of the stm32f7_i2c_reg_slave function.
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d3be711e065a97a57c2f2ffba3098748855bd6 upstream.
The IP can handle two slave addresses. One address can either be
7 bits or 10 bits while the other can only be 7 bits.
In order to ensure that a 10 bits address can always be allocated
(assuming there is only one 7 bits address already allocated),
pick up the 7-bits only address slot in priority when performing a 7-bits
address allocation.
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf8ce8b80f8bf9669f6ec4e71e16668430febdac upstream.
The I2C specification states that tsu:sto for standard mode timing must
be at minimum 4us. Pictographically, this is:
SCL: ____/~~~~~~~~~
SDA: _________/~~~~
->| |<- 4us minimum
We are currently waiting 2.5us between asserting SCL and SDA, which is
in violation of the standard. Adjust the timings to ensure that we meet
what is stipulated as the minimum timings to ensure that all devices
correctly interpret the STOP bus transition.
This is more important than trying to generate a square wave with even
duty cycle.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fece4978510e43f09c8cd386fee15210e8c68493 ]
Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
