IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 2fe8a236436fe40d8d26a1af8d150fc80f04ee1a ]
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit db46cd1e0426f52999d50fa72cfa97fa39952885 upstream.
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path.
Cc: <stable@vger.kernel.org>
Fixes: 4fa52aa7a82f ("[S390] dasd: add enhanced DASD statistics interface")
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20231025132437.1223363-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b481f644d9174670b385c3a699617052cd2a79d3 upstream.
When device_register() fails, zfcp_port_release() will be called after
put_device(). As a result, zfcp_ccw_adapter_put() will be called twice: one
in zfcp_port_release() and one in the error path after device_register().
So the reference on the adapter object is doubly put, which may lead to a
premature free. Fix this by adjusting the error tag after
device_register().
Fixes: f3450c7b9172 ("[SCSI] zfcp: Replace local reference counting with common kref")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230923103723.10320-1-dinghao.liu@zju.edu.cn
Acked-by: Benjamin Block <bblock@linux.ibm.com>
Cc: stable@vger.kernel.org # v2.6.33+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a2278ce9c25048d999fe1a3561def75d963f471 ]
The DASD device driver has a function to requeue requests to the
blocklayer.
This function is used in various cases when basic settings for the device
have to be changed like High Performance Ficon related parameters or copy
pair settings.
The functions iterates over the device->ccw_queue and also removes the
requests from the block->ccw_queue.
In case the device is started on an alias device instead of the base
device it might be removed from the block->ccw_queue without having it
canceled properly before. This might lead to a hanging device since the
request is no longer on a queue and can not be handled properly.
Fix by iterating over the block->ccw_queue instead of the
device->ccw_queue. This will take care of all blocklayer related requests
and handle them on all associated DASD devices.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acea28a6b74f458defda7417d2217b051ba7d444 ]
If a DASD request fails an error recovery procedure (ERP) request might
be built as a copy of the original request to do error recovery.
The ERP request gets a number of retries assigned.
This number is always 256 no matter what other value might have been set
for the original request. This is not what is expected when a user
specifies a certain amount of retries for the device via sysfs.
Correctly use the number of retries of the original request for ERP
requests.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e65851989001c0c9ba9177564b13b38201c0854c upstream.
Storage devices are free to send RSCNs, e.g. for internal state changes. If
this happens on all connected paths, zfcp risks temporarily losing all
paths at the same time. This has strong requirements on multipath
configuration such as "no_path_retry queue".
Avoid such situations by deferring fc_rport blocking until after the ADISC
response, when any actual state change of the remote port became clear.
The already existing port recovery triggers explicitly block the fc_rport.
The triggers are: on ADISC reject or timeout (typical cable pull case), and
on ADISC indicating that the remote port has changed its WWPN or
the port is meanwhile no longer open.
As a side effect, this also removes a confusing direct function call to
another work item function zfcp_scsi_rport_work() instead of scheduling
that other work item. It was probably done that way to have the rport block
side effect immediate and synchronous to the caller.
Fixes: a2fa0aede07c ("[SCSI] zfcp: Block FC transport rports early on errors")
Cc: stable@vger.kernel.org #v2.6.30+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Fedor Loshakov <loshakov@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Link: https://lore.kernel.org/r/20230724145156.3920244-1-maier@linux.ibm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05f1d8ed03f547054efbc4d29bb7991c958ede95 upstream.
Quiesce and resume are functions that tell the DASD driver to stop/resume
issuing I/Os to a specific DASD.
On resume dasd_schedule_block_bh() is called to kick handling of IO
requests again. This does unfortunately not cover internal requests which
are used for path verification for example.
This could lead to a hanging device when a path event or anything else
that triggers internal requests occurs on a quiesced device.
Fix by also calling dasd_schedule_device_bh() which triggers handling of
internal requests on resume.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89c0c62e947a01e7a36b54582fd9c9e346170255 ]
Currently, if the device is offline and all the channel paths are
either configured or varied offline, the associated subchannel gets
unregistered. Don't unregister the subchannel, instead unregister
offline device.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2862a2fdfae875888e3c1c3634e3422e01d98147 ]
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: Steffen Maier <maier@linux.ibm.com>
Fixes: 8129ee164267 ("[PATCH] s390: qdio V=V pass-through")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8898ee50edecacdf0141f26fd90acf43d7e9cd7 upstream.
The DASD driver does not kick the requeue list when requeuing IO requests
to the blocklayer. This might lead to hanging blockdevice when there is
no other trigger for this.
Fix by automatically kick the requeue list when requeuing DASD requests
to the blocklayer.
Fixes: e443343e509a ("s390/dasd: blk-mq conversion")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-8-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb16db8393658e0978c3f0d30ae069e878264fa3 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88d86d18d7cf7e9137c95f9d212bb9fff8a1b4be ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa5bf80c3c067b82b4362cd6e8e2194623bcaca6 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/ctcm_main.c:1064:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcm_tx,
^~~~~~~
drivers/s390/net/ctcm_main.c:1072:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcmpc_tx,
^~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of ctc{mp,}m_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 590ce6d96d6a224b470a3862c33a483d5022bfdb ]
For DASD devices in raw_track_access mode only full track images are
read and written.
For this purpose it is not necessary to do search operation in the
locate record extended function. The documentation even states that
this might fail if the searched record is not found on a track.
Currently the driver sets a value of 1 in the search field for the first
record after record zero. This is the default for disks not in
raw_track_access mode but record 1 might be missing on a completely
empty track.
There has not been any problem with this on IBM storage servers but it
might lead to errors with DASD devices on other vendors storage servers.
Fix this by setting the search field to 0. Record zero is always available
even on a completely empty track.
Fixes: e4dbb0f2b5dd ("[S390] dasd: Add support for raw ECKD access.")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20221123160719.3002694-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit db7ba07108a48c0f95b74fabbfd5d63e924f992d upstream.
Fix Oops in dasd_alias_get_start_dev() function caused by the pavgroup
pointer being NULL.
The pavgroup pointer is checked on the entrance of the function but
without the lcu->lock being held. Therefore there is a race window
between dasd_alias_get_start_dev() and _lcu_update() which sets
pavgroup to NULL with the lcu->lock held.
Fix by checking the pavgroup pointer with lcu->lock held.
Cc: <stable@vger.kernel.org> # 2.6.25+
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20220919154931.4123002-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4da8c5f76825269f28d6a89fa752934a4bcb6dfa upstream.
Case (1):
The only waiter on wka_port->completion_wq is zfcp_fc_wka_port_get()
trying to open a WKA port. As such it should only be woken up by WKA port
*open* responses, not by WKA port close responses.
Case (2):
A close WKA port response coming in just after having sent a new open WKA
port request and before blocking for the open response with wait_event()
in zfcp_fc_wka_port_get() erroneously renders the wait_event a NOP
because the close handler overwrites wka_port->status. Hence the
wait_event condition is erroneously true and it does not enter blocking
state.
With non-negligible probability, the following time space sequence happens
depending on timing without this fix:
user process ERP thread zfcp work queue tasklet system work queue
============ ========== =============== ======= =================
$ echo 1 > online
zfcp_ccw_set_online
zfcp_ccw_activate
zfcp_erp_adapter_reopen
msleep scan backoff zfcp_erp_strategy
| ...
| zfcp_erp_action_cleanup
| ...
| queue delayed scan_work
| queue ns_up_work
| ns_up_work:
| zfcp_fc_wka_port_get
| open wka request
| open response
| GSPN FC-GS
| RSPN FC-GS [NPIV-only]
| zfcp_fc_wka_port_put
| (--wka->refcount==0)
| sched delayed wka->work
|
~~~Case (1)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
zfcp_erp_wait
flush scan_work
| wka->work:
| wka->status=CLOSING
| close wka request
| scan_work:
| zfcp_fc_wka_port_get
| (wka->status==CLOSING)
| wka->status=OPENING
| open wka request
| wait_event
| | close response
| | wka->status=OFFLINE
| | wake_up /*WRONG*/
~~~Case (2)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| wka->work:
| wka->status=CLOSING
| close wka request
zfcp_erp_wait
flush scan_work
| scan_work:
| zfcp_fc_wka_port_get
| (wka->status==CLOSING)
| wka->status=OPENING
| open wka request
| close response
| wka->status=OFFLINE
| wake_up /*WRONG&NOP*/
| wait_event /*NOP*/
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| (wka->status!=ONLINE)
| return -EIO
| return early
open response
wka->status=ONLINE
wake_up /*NOP*/
So we erroneously end up with no automatic port scan. This is a big problem
when it happens during boot. The timing is influenced by v3.19 commit
18f87a67e6d6 ("zfcp: auto port scan resiliency").
Fix it by fully mutually excluding zfcp_fc_wka_port_get() and
zfcp_fc_wka_port_offline(). For that to work, we make the latter block
until we got the response for a close WKA port. In order not to penalize
the system workqueue, we move wka_port->work to our own adapter workqueue.
Note that before v2.6.30 commit 828bc1212a68 ("[SCSI] zfcp: Set WKA-port to
offline on adapter deactivation"), zfcp did block in
zfcp_fc_wka_port_offline() as well, but with a different condition.
While at it, make non-functional cleanups to improve code reading in
zfcp_fc_wka_port_get(). If we cannot send the WKA port open request, don't
rely on the subsequent wait_event condition to immediately let this case
pass without blocking. Also don't want to rely on the additional condition
handling the refcount to be skipped just to finally return with -EIO.
Link: https://lore.kernel.org/r/20220729162529.1620730-1-maier@linux.ibm.com
Fixes: 5ab944f97e09 ("[SCSI] zfcp: attach and release SAN nameserver port on demand")
Cc: <stable@vger.kernel.org> #v2.6.28+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ffed254d938c9e99eb7761c7f739294c84e0367 ]
Memory buffer used for reading out data from hardware system
area is not protected against concurrent access.
Reported-by: Matthew Wilcox <willy@infradead.org>
Fixes: 411ed3225733 ("[S390] zfcpdump support.")
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/e68137f0f9a0d2558f37becc20af18e2939934f6.1658206891.git.agordeev@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cffcc109fd682075dee79bade3d60a07152a8fd1 ]
The routine vfio_ccw_sch_event() is tasked with handling subchannel events,
specifically machine checks, on behalf of vfio-ccw. It correctly calls
cio_update_schib(), and if that fails (meaning the subchannel is gone)
it makes an FSM event call to mark the subchannel Not Operational.
If that worked, however, then it decides that if the FSM state was already
Not Operational (implying the subchannel just came back), then it should
simply change the FSM to partially- or fully-open.
Remove this trickery, since a subchannel returning will require more
probing than simply "oh all is well again" to ensure it works correctly.
Fixes: bbe37e4cb8970 ("vfio: ccw: introduce a finite state machine")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Link: https://lore.kernel.org/r/20220707135737.720765-4-farman@linux.ibm.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b68b914494df4f79b4e9b58953110574af1cb7a2 upstream.
Since commit a9c3f68f3cd8d (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
the rest of the users.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 671bb35c8e746439f0ed70815968f9a4f20a8deb ]
smatch complains about
drivers/s390/net/lcs.c:1741 lcs_get_control() warn: variable dereferenced before check 'card->dev' (see line 1739)
Fixes: 27eb5ac8f015 ("[PATCH] s390: lcs driver bug fixes and improvements [1/2]")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c0b20587b9f25a2ad14db7f80ebe49bdf29920a ]
smatch complains about
drivers/s390/net/ctcm_mpc.c:1210 ctcmpc_unpack_skb() warn: possible memory leak of 'mpcginfo'
mpc_action_discontact() did not free mpcginfo. Consolidate the freeing in
ctcmpc_unpack_skb().
Fixes: 293d984f0e36 ("ctcm: infrastructure for replaced ctc driver")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c50c6867c85afee6f2b3bcbc50fc9d0083d1343 ]
Found by cppcheck and smatch.
smatch complains about
drivers/s390/net/ctcm_sysfs.c:43 ctcm_buffer_write() warn: variable dereferenced before check 'priv' (see line 42)
Fixes: 3c09e2647b5e ("ctcm: rename READ/WRITE defines to avoid redefinitions")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8c9db6679be4348b8aae108e11d4be2f83976e30 upstream.
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213fca9e23b59581c573d558aa477556f00b8198 upstream.
commit 9c6c273aa424 ("timer: Remove init_timer_on_stack() in favor
of timer_setup_on_stack()") changed the timer setup from
init_timer_on_stack(() to timer_setup(), but missed to change the
mod_timer() call. And while at it, use msecs_to_jiffies() instead
of the open coded timeout calculation.
Cc: stable@vger.kernel.org
Fixes: 9c6c273aa424 ("timer: Remove init_timer_on_stack() in favor of timer_setup_on_stack()")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3683c055212bf910d4e318f7944910ce10dbee6 ]
Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7d91d230a119fdcc334d10c9889ce9c5e15118b ]
Console name reported in /proc/consoles:
ttyS1 -W- (EC p ) 4:65
does not match the char device name:
crw--w---- 1 root root 4, 65 May 17 12:18 /dev/ttysclp0
so debian-installer inside a QEMU s390x instance gets confused and fails
to start with the following error:
steal-ctty: No such file or directory
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Link: https://lore.kernel.org/r/20210427194010.9330-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c749d8c018daf5fba6dfac7b6c5c78b27efd7d65 upstream.
Currently css_wait_for_slow_path() gets called inside the chp->lock.
The path-verification-loop of slowpath inside this lock could lead to
deadlock as reported by the lockdep validator.
The ccw_device_get_chp_desc() during the instance of a device-set-online
would try to acquire the same 'chp->lock' to read the chp->desc.
The instance of this function can get called from multiple scenario,
like probing or setting-device online manually. This could, in some
corner-cases lead to the deadlock.
lockdep validator reported this as,
CPU0 CPU1
---- ----
lock(&chp->lock);
lock(kn->active#43);
lock(&chp->lock);
lock((wq_completion)cio);
The chp->lock was introduced to serialize the access of struct
channel_path. This lock is not needed for the css_wait_for_slow_path()
function, so invoke the slow-path function outside this lock.
Fixes: b730f3a93395 ("[S390] cio: add lock to struct channel_path")
Cc: <stable@vger.kernel.org>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66f669a272898feb1c69b770e1504aa2ec7723d1 upstream.
Prevent that an IO request is build during device shutdown initiated by
a driver unbind. This request will never be able to be processed or
canceled and will hang forever. This will lead also to a hanging unbind.
Fix by checking not only if the device is in READY state but also check
that there is no device offline initiated before building a new IO request.
Fixes: e443343e509a ("s390/dasd: blk-mq conversion")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Tested-by: Bjoern Walk <bwalk@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d365bd0bff3c0310c39ebaffc9a8458e036d666 upstream.
In case of an unbind of the DASD device driver the function
dasd_generic_remove() is called which shuts down the device.
Among others this functions removes the int_handler from the cdev.
During shutdown the device cancels all outstanding IO requests and waits
for completion of the clear request.
Unfortunately the clear interrupt will never be received when there is no
interrupt handler connected.
Fix by moving the int_handler removal after the call to the state machine
where no request or interrupt is outstanding.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Tested-by: Bjoern Walk <bwalk@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51c44babdc19aaf882e1213325a0ba291573308f upstream.
The copy_to_user() function returns the number of bytes remaining to be
copied, but we want to return -EFAULT if the copy doesn't complete.
Fixes: e01bcdd61320 ("vfio: ccw: realize VFIO_DEVICE_GET_REGION_INFO ioctl")
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/1614600093-13992-1-git-send-email-wangqing@vivo.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fef912bf860e8e7e48a2bfb978a356bba743a8b7 upstream.
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 182f709c5cff683e6732d04c78e328de0532284f upstream.
CCW_CMD_READ_STATUS was introduced with revision 2 of virtio-ccw,
and drivers should only rely on it being implemented when they
negotiated at least that revision with the device.
However, virtio_ccw_get_status() issued READ_STATUS for any
device operating at least at revision 1. If the device accepts
READ_STATUS regardless of the negotiated revision (which some
implementations like QEMU do, even though the spec currently does
not allow it), everything works as intended. While a device
rejecting the command should also be handled gracefully, we will
not be able to see any changes the device makes to the status,
such as setting NEEDS_RESET or setting the status to zero after
a completed reset.
We negotiated the revision to at most 1, as we never bumped the
maximum revision; let's do that now and properly send READ_STATUS
only if we are operating at least at revision 2.
Cc: stable@vger.kernel.org
Fixes: 7d3ce5ab9430 ("virtio/s390: support READ_STATUS command for virtio-ccw")
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20210216110645.1087321-1-cohuck@redhat.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a7f655834c7c335bf683f248208d4fbe4b47bc upstream.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ede91f83aa335da1c3ec68eb0f9e228f269f6d8 upstream.
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a29ea01653493b94ea12bb2b89d1564a265081b6 upstream.
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 658a337a606f48b7ebe451591f7681d383fa115e upstream.
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ed10e16e50daf74460f54bc922e27c6863c8d61 ]
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792c2 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f117cb854a44a79898d844e6ae3fd23bd94e786 upstream.
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e80983f0cf470bb82036e73bff4d5a7daf8fc2 upstream.
reqcnt is an u32 pointer but we do copy sizeof(reqcnt) which is the
size of the pointer. This means we only copy 8 byte. Let us copy
the full monty.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes: af4a72276d49 ("s390/zcrypt: Support up to 256 crypto adapters.")
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 709192d531e5b0a91f20aa14abfe2fc27ddd47af upstream.
A discard request that writes zeros using the global kernel internal
ZERO_PAGE will fail for machines with more than 2GB of memory due to the
location of the ZERO_PAGE.
Fix this by using a driver owned global zero page allocated with GFP_DMA
flag set.
Fixes: 28b841b3a7cb ("s390/dasd: Add discard support for FBA devices")
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b8eb2ee9da1e8c9b8082f404f3948aa82a057b2 ]
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2d9a2c5f581be3991ba67fa9e7497c711220ea8e upstream.
Before v4.15 commit 75492a51568b ("s390/scsi: Convert timers to use
timer_setup()"), we intentionally only passed zfcp_adapter as context
argument to zfcp_fsf_request_timeout_handler(). Since we only trigger
adapter recovery, it was unnecessary to sync against races between timeout
and (late) completion. Likewise, we only passed zfcp_erp_action as context
argument to zfcp_erp_timeout_handler(). Since we only wakeup an ERP action,
it was unnecessary to sync against races between timeout and (late)
completion.
Meanwhile the timeout handlers get timer_list as context argument and do a
timer-specific container-of to zfcp_fsf_req which can have been freed.
Fix it by making sure that any request timeout handlers, that might just
have started before del_timer(), are completed by using del_timer_sync()
instead. This ensures the request free happens afterwards.
Space time diagram of potential use-after-free:
Basic idea is to have 2 or more pending requests whose timeouts run out at
almost the same time.
req 1 timeout ERP thread req 2 timeout
---------------- ---------------- ---------------------------------------
zfcp_fsf_request_timeout_handler
fsf_req = from_timer(fsf_req, t, timer)
adapter = fsf_req->adapter
zfcp_qdio_siosl(adapter)
zfcp_erp_adapter_reopen(adapter,...)
zfcp_erp_strategy
...
zfcp_fsf_req_dismiss_all
list_for_each_entry_safe
zfcp_fsf_req_complete 1
del_timer 1
zfcp_fsf_req_free 1
zfcp_fsf_req_complete 2
zfcp_fsf_request_timeout_handler
del_timer 2
fsf_req = from_timer(fsf_req, t, timer)
zfcp_fsf_req_free 2
adapter = fsf_req->adapter
^^^^^^^ already freed
Link: https://lore.kernel.org/r/20200813152856.50088-1-maier@linux.ibm.com
Fixes: 75492a51568b ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02472e28b9a45471c6d8729ff2c7422baa9be46a ]
Discard events that don't contain any entries. This shouldn't happen,
but subsequent code relies on being able to use entry 0. So better
be safe than accessing garbage.
Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 936e6b85da0476dd2edac7c51c68072da9fb4ba2 upstream.
Suppose that, for unrelated reasons, FSF requests on behalf of recovery are
very slow and can run into the ERP timeout.
In the case at hand, we did adapter recovery to a large degree. However
due to the slowness a LUN open is pending so the corresponding fc_rport
remains blocked. After fast_io_fail_tmo we trigger close physical port
recovery for the port under which the LUN should have been opened. The new
higher order port recovery dismisses the pending LUN open ERP action and
dismisses the pending LUN open FSF request. Such dismissal decouples the
ERP action from the pending corresponding FSF request by setting
zfcp_fsf_req->erp_action to NULL (among other things)
[zfcp_erp_strategy_check_fsfreq()].
If now the ERP timeout for the pending open LUN request runs out, we must
not use zfcp_fsf_req->erp_action in the ERP timeout handler. This is a
problem since v4.15 commit 75492a51568b ("s390/scsi: Convert timers to use
timer_setup()"). Before that we intentionally only passed zfcp_erp_action
as context argument to zfcp_erp_timeout_handler().
Note: The lifetime of the corresponding zfcp_fsf_req object continues until
a (late) response or an (unrelated) adapter recovery.
Just like the regular response path ignores dismissed requests
[zfcp_fsf_req_complete() => zfcp_fsf_protstatus_eval() => return early] the
ERP timeout handler now needs to ignore dismissed requests. So simply
return early in the ERP timeout handler if the FSF request is marked as
dismissed in its status flags. To protect against the race where
zfcp_erp_strategy_check_fsfreq() dismisses and sets
zfcp_fsf_req->erp_action to NULL after our previous status flag check,
return early if zfcp_fsf_req->erp_action is NULL. After all, the former
ERP action does not need to be woken up as that was already done as part of
the dismissal above [zfcp_erp_action_dismiss()].
This fixes the following panic due to kernel page fault in IRQ context:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:000009859238c00b R2:00000e3e7ffd000b R3:00000e3e7ffcc007 S:00000e3e7ffd7000 P:000000000000013d
Oops: 0004 ilc:2 [#1] SMP
Modules linked in: ...
CPU: 82 PID: 311273 Comm: stress Kdump: loaded Tainted: G E X ...
Hardware name: IBM 8561 T01 701 (LPAR)
Krnl PSW : 0404c00180000000 001fffff80549be0 (zfcp_erp_notify+0x40/0xc0 [zfcp])
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000080 00000e3d00000000 00000000000000f0 0000000000030000
000000010028e700 000000000400a39c 000000010028e700 00000e3e7cf87e02
0000000010000000 0700098591cb67f0 0000000000000000 0000000000000000
0000033840e9a000 0000000000000000 001fffe008d6bc18 001fffe008d6bbc8
Krnl Code: 001fffff80549bd4: a7180000 lhi %r1,0
001fffff80549bd8: 4120a0f0 la %r2,240(%r10)
#001fffff80549bdc: a53e0003 llilh %r3,3
>001fffff80549be0: ba132000 cs %r1,%r3,0(%r2)
001fffff80549be4: a7740037 brc 7,1fffff80549c52
001fffff80549be8: e320b0180004 lg %r2,24(%r11)
001fffff80549bee: e31020e00004 lg %r1,224(%r2)
001fffff80549bf4: 412020e0 la %r2,224(%r2)
Call Trace:
[<001fffff80549be0>] zfcp_erp_notify+0x40/0xc0 [zfcp]
[<00000985915e26f0>] call_timer_fn+0x38/0x190
[<00000985915e2944>] expire_timers+0xfc/0x190
[<00000985915e2ac4>] run_timer_softirq+0xec/0x218
[<0000098591ca7c4c>] __do_softirq+0x144/0x398
[<00000985915110aa>] do_softirq_own_stack+0x72/0x88
[<0000098591551b58>] irq_exit+0xb0/0xb8
[<0000098591510c6a>] do_IRQ+0x82/0xb0
[<0000098591ca7140>] ext_int_handler+0x128/0x12c
[<0000098591722d98>] clear_subpage.constprop.13+0x38/0x60
([<000009859172ae4c>] clear_huge_page+0xec/0x250)
[<000009859177e7a2>] do_huge_pmd_anonymous_page+0x32a/0x768
[<000009859172a712>] __handle_mm_fault+0x88a/0x900
[<000009859172a860>] handle_mm_fault+0xd8/0x1b0
[<0000098591529ef6>] do_dat_exception+0x136/0x3e8
[<0000098591ca6d34>] pgm_check_handler+0x1c8/0x220
Last Breaking-Event-Address:
[<001fffff80549c88>] zfcp_erp_timeout_handler+0x10/0x18 [zfcp]
Kernel panic - not syncing: Fatal exception in interrupt
Link: https://lore.kernel.org/r/20200623140242.98864-1-maier@linux.ibm.com
Fixes: 75492a51568b ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75e82bec6b2622c6f455b7a543fb5476a5d0eed7 ]
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq().
If the subsequent qdio_establish_thinint() fails, we miss to put the
DSCI again. Thus the DSCI isn't available for re-use. Given enough of
such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with
such an error internally.
Fixes: 779e6e1c724d ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ce3e53f375295c2940390b2b429e506e07655c ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.
To fix this, only generate the ADD event if uevents were still
suppressed for the device.
Fixes: fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com>
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
