IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 3baa4c5143 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d0 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f0 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478 ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882 ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc3 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad37b5e30 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac08bda156 ]
Commit 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
attempted to fix the PWM settings but ended up causin an additional clock
reparenting error:
clk: failed to reparent abe-clkctrl:0060:24 to sys_clkin_ck: -22
Only timer9 is in the PER domain and can use the sys_clkin_ck clock source.
For timer8, the there is no sys_clkin_ck available as it's in the ABE
domain, instead it should use syc_clk_div_ck. However, for power
management, we want to use the always on sys_32k_ck instead.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
Depends-on: 61978617e9 ("ARM: dts: Add minimal support for Droid Bionic xt875")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44ad820780 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f5 ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7260b36345 ]
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-15-krzk@kernel.org
Stable-dep-of: 982655cb0e ("ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5911622eff ]
The SROM controller is modeled with a bus so align the device node name
with dtschema to fix warning:
srom-cs1@18000000: $nodename:0: 'srom-cs1@18000000'
does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-5-krzk@kernel.org
Stable-dep-of: cf0cb2af6a ("ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b81a8dece ]
The fixed clocks are kept under dedicated 'clocks' node but this causes
multiple dtschema warnings:
clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
clocks: #size-cells:0:0: 0 is not one of [1, 2]
clocks: oscillator@0:reg:0: [0] is too short
clocks: oscillator@1:reg:0: [1] is too short
clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-3-krzk@kernel.org
Stable-dep-of: cf0cb2af6a ("ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3392ef368d ]
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-3-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05d2c3d552 ]
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-2-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74abbfe99f ]
In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stable-dep-of: 05d2c3d552 ("ARM: dts: BCM53573: Drop nonexistent #usb-cells")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8b3b8a18 ]
Add usb alias for bootloader searching the controller in correct order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: ee70b908f7 ("ARM: dts: nxp/imx6sll: fix wrong property name in usbphy node")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da1b522cf ]
In imx6sll.dtsi, the ssi node name is different with other
platforms (imx6qdl, imx6sl, imx6sx), but the
sound/soc/fsl/fsl-asoc-card.c machine driver needs to check
ssi node name for audmux configuration, then different ssi
node name causes issue on imx6sll platform.
So we change ssi node name to make all platforms have same
name.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: ee70b908f7 ("ARM: dts: nxp/imx6sll: fix wrong property name in usbphy node")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c8e2c575 ]
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230503122830.3200-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
