IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 0b74e40a4e41f3cbad76dff4c50850d47b525b26 ]
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c742f ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d66 ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1d5 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa86fc2e28227f1e64f13867e73cf864c6d25ad ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f50574 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 175b8d89fe292796811fdee87fa39799a5b6b87a upstream.
syzbot spotted a potential out-of-bounds shift in the PCM OSS layer
where it calculates the buffer size with the arbitrary shift value
given via an ioctl.
Add a range check for avoiding the undefined behavior.
As the value can be treated by a signed integer, the max shift should
be 30.
Reported-by: syzbot+df7dc146ebdd6435eea3@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209084552.17109-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 862ee699fefe1e6d6f2c1518395f0b999b8beb15 upstream.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
Make it depend on BROKEN for now.
Fixes: 1bbb4f2035d9 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1373f10479b624fb6dba0805d673e860f1b421d upstream.
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd071aea9d1ce64279178e470977b235c upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43d5ca88dfcd35e43010fdd818e067aa9a55f5ba upstream.
syzbot spotted a potential out-of-bounds shift in the USB-audio format
parser that receives the arbitrary shift value from the USB
descriptor.
Add a range check for avoiding the undefined behavior.
Reported-by: syzbot+df7dc146ebdd6435eea3@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209084552.17109-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a02f954b0def3ada8ed6d4b2c7bcb67e885e9c upstream.
I got reports that some models of this old scanner need
this when using runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e90cfa813da7a527785033a0b247594c2de93dd8 upstream.
This error path
err_add_pdata:
for (i = 0; i < mod_data.num; i++)
kfree(dum[i]);
can be triggered when not all dum's elements are initialized.
Fix this by initializing all dum's elements to NULL.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/1607063090-3426-1-git-send-email-minhquangbui99@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee4f52a8de2c6f78b01f10b4c330867d88c1653a ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f8ed289fab84 ("bridge: vlan: use br_vlan_(get|put)_master to deal with refcounts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/1607071737-33875-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82ca4c922b8992013a238d65cf4e60cc33e12f36 ]
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f58591323bf3f342920179f24515935c4b5fd60 ]
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2ae0b ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 299bcb55ecd1412f6df606e9dc0912d55610029e ]
When cwnd is not a multiple of the TSO skb size of N*MSS, we can get
into persistent scenarios where we have the following sequence:
(1) ACK for full-sized skb of N*MSS arrives
-> tcp_write_xmit() transmit full-sized skb with N*MSS
-> move pacing release time forward
-> exit tcp_write_xmit() because pacing time is in the future
(2) TSQ callback or TCP internal pacing timer fires
-> try to transmit next skb, but TSO deferral finds remainder of
available cwnd is not big enough to trigger an immediate send
now, so we defer sending until the next ACK.
(3) repeat...
So we can get into a case where we never mark ourselves as
cwnd-limited for many seconds at a time, even with
bulk/infinite-backlog senders, because:
o In case (1) above, every time in tcp_write_xmit() we have enough
cwnd to send a full-sized skb, we are not fully using the cwnd
(because cwnd is not a multiple of the TSO skb size). So every time we
send data, we are not cwnd limited, and so in the cwnd-limited
tracking code in tcp_cwnd_validate() we mark ourselves as not
cwnd-limited.
o In case (2) above, every time in tcp_write_xmit() that we try to
transmit the "remainder" of the cwnd but defer, we set the local
variable is_cwnd_limited to true, but we do not send any packets, so
sent_pkts is zero, so we don't call the cwnd-limited logic to update
tp->is_cwnd_limited.
Fixes: ca8a22634381 ("tcp: make cwnd-limited checks measurement-based, and gentler")
Reported-by: Ingemar Johansson <ingemar.s.johansson@ericsson.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201209035759.1225145-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fed91613c9dd455dd154b22fa8e11b8526466082 ]
Add restarting state flag to avoid scheduling another restart task while
such task is already running. Change task name from watchdog_task to
restart_task to better fit the task role.
Fixes: 1e338db56e5a ("mlx4_en: Fix a race at restart task")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddf75be47ca748f8b12d28ac64d624354fddf189 upstream
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae447 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeaf06af6f87e1dba371fbe42674e6f963220b9c upstream.
My patch caused kernel Oopses and delays in boot. Revert it.
The problem was that I moved the "mem->dma = paddr;" before the call to
be_fill_queue(). But the first thing that the be_fill_queue() function
does is memset the whole struct to zero which overwrites the assignment.
Link: https://lore.kernel.org/r/X8jXkt6eThjyVP1v@mwanda
Fixes: 38b2db564d9a ("scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()")
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a0001436352c9853d72bf2071e85b316d688a2 upstream.
Debounce filter setting should be independent from IRQ type setting
because according to the ACPI specs, there are separate arguments for
specifying debounce timeout and IRQ type in GpioIo() and GpioInt().
Together with commit 06abe8291bc31839950f7d0362d9979edc88a666
("pinctrl: amd: fix incorrect way to disable debounce filter") and
Andy's patch "gpiolib: acpi: Take into account debounce settings" [1],
this will fix broken touchpads for laptops whose BIOS set the
debounce timeout to a relatively large value. For example, the BIOS
of Lenovo AMD gaming laptops including Legion-5 15ARH05 (R7000),
Legion-5P (R7000P) and IdeaPad Gaming 3 15ARH05, set the debounce
timeout to 124.8ms. This led to the kernel receiving only ~7 HID
reports per second from the Synaptics touchpad
(MSFT0001:00 06CB:7F28).
Existing touchpads like [2][3] are not troubled by this bug because
the debounce timeout has been set to 0 by the BIOS before enabling
the debounce filter in setting IRQ type.
[1] https://lore.kernel.org/linux-gpio/20201111222008.39993-11-andriy.shevchenko@linux.intel.com/
8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
[2] https://github.com/Syniurge/i2c-amd-mp2/issues/11#issuecomment-721331582
[3] https://forum.manjaro.org/t/random-short-touchpad-freezes/30832/28
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-gpio/CAHp75VcwiGREBUJ0A06EEw-SyabqYsp%2Bdqs2DpSrhaY-2GVdAA%40mail.gmail.com/
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1887190
Link: https://lore.kernel.org/r/20201125130320.311059-1-coiby.xu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce6520b0eafad5962ffc21dc47cd7bd3250e9045 upstream.
The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20201207071250.15021-1-chiu@endlessos.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82e06090473289ce63e23fdeb8737aad59b10645 upstream.
We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().
Reported-and-tested-by: syzbot+150f793ac5bc18eee150@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e42404fa10fd11fe72d0a0e149a321d10e577715 ]
To start stack unwinding (SP, PC and BLINK) are needed. When the
explicit execution context (pt_regs etc) is not available, unwinder
assumes the task is sleeping (in __switch_to()) and fetches SP and BLINK
from kernel mode stack.
But this assumption is not true, specially in a SMP system, when top
runs on 1 core, there may be active running processes on all cores.
So when unwinding non courrent tasks, ensure they are NOT running.
And while at it, handle the self unwinding case explicitly.
This came out of investigation of a customer reported hang with
rcutorture+top
Link: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/31
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0011c6d182774fc781fb9e115ebe8baa356029ae ]
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
[1]
https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201104162356.1251-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04516706bb99889986ddfa3a769ed50d2dc7ac13 ]
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d853b3406903a7dc5b14eb5bada3e8cd677f66a2 ]
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc4781 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to 4.19-stable, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.4+: e13ee6cc4781: spi: bcm2835aux: Fix use-after-free on unbind
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e13ee6cc4781edaf8c7321bee19217e3702ed481 ]
bcm2835aux_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: b9dd3f6d4172 ("spi: bcm2835aux: Fix controller unregister order")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.4+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.4+: b9dd3f6d4172: spi: bcm2835aux: Fix controller unregister order
Cc: <stable@vger.kernel.org> # v4.4+
Link: https://lore.kernel.org/r/b290b06357d0c0bdee9cecc539b840a90630f101.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9a5ae8df5b3365183150f6df49e49dece80d8c upstream
Since insn.prefixes.nbytes can be bigger than the size of
insn.prefixes.bytes[] when a prefix is repeated, the proper check must
be
insn.prefixes.bytes[i] != 0 and i < 4
instead of using insn.prefixes.nbytes.
Introduce a for_each_insn_prefix() macro for this purpose. Debugged by
Kees Cook <keescook@chromium.org>.
[ bp: Massage commit message, sync with the respective header in tools/
and drop "we". ]
Fixes: 2b1444983508 ("uprobes, mm, x86: Add the ability to install and remove uprobes breakpoints")
Reported-by: syzbot+9b64b619f10f19d19a7c@syzkaller.appspotmail.com
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/160697103739.3146288.7437620795200799020.stgit@devnote2
[sudip: adjust context, use old insn.h]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 855b69857830f8d918d715014f05e59a3f7491a0 upstream.
Fix to return a negative error code from the error handling case
instead of 0 in function i8042_setup_aux(), as done elsewhere in this
function.
Fixes: f81134163fc7 ("Input: i8042 - use platform_driver_probe")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Luo Meng <luomeng12@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201123133420.4071187-1-luomeng12@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 778721510e84209f78e31e2ccb296ae36d623f5e upstream.
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcee5278958802b40ee8b26679155a6d9231783e upstream.
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org
Fixes: 16270145ce6b ("tracing: Add trace options for core options to instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 666224b43b4bd4612ce3b758c038f9bc5c5e3fcb ]
The DMA channel was not released if either devm_request_irq() or
devm_spi_register_controller() failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191212135550.4634-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to 4.19-stable]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1483ac030fb4c57734289742f1c1d38dca61e22 ]
bcm2835_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: f8043872e796 ("spi: add driver for BCM2835")
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v3.10+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v3.10+
Cc: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/ad66e0a0ad96feb848814842ecf5b6a4539ef35c.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63c5395bb7a9777a33f0e7b5906f2c0170a23692 ]
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/5e31a9a59fd1c0d0b795b2fe219f25e5ee855f9d.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e844cc37a5cbaa460e68f9a989d321d63088a89 ]
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_master()
spi_unregister_master()
That's because spi_unregister_master() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_master which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_master struct. Thus, once spi_unregister_master() has been
called, the private data is inaccessible. But some drivers need to
access it after spi_unregister_master() to perform further teardown
steps.
Introduce devm_spi_alloc_master(), which releases a reference on the
spi_master struct only after the driver has unbound, thereby keeping the
memory allocation accessible. Change spi_unregister_master() to not
release a reference if the spi_master was allocated by the new devm
function.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_master in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm function
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the master.
That commit shall amend spi_unregister_master() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4165bf015ba9454f45beaad621d16c516d5c5afe upstream.
According to the AMD IOMMU spec, the commit 73db2fc595f3
("iommu/amd: Increase interrupt remapping table limit to 512 entries")
also requires the interrupt table length (IntTabLen) to be set to 9
(power of 2) in the device table mapping entry (DTE).
Fixes: 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries")
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20201207091920.3052-1-suravee.suthikulpanit@amd.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3dee7a279ebe4d892b359fe3696938ec15 upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f70a876c2e78e58c5ca0bbf0547e4f6d upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0ff4e4bf7a45b5aef9639799719c28d0073 upstream.
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: a124692b698b0 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990c158d5b1dabd166516e21992baef5f26a upstream.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bbd4 ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf193bfc12dbc3754fc8a6e0e1e3702f1af2f772 upstream.
Keep the device-id entries sorted to make it easier to add new ones in
the right spot.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ee4abb10a07bd8f8ce910ee6b4ae6a947d7f63 upstream.
Add PID for CH340 that's found on a ch341 based Programmer made by keeyees.
The specific device that contains the serial converter is described
here: http://www.keeyees.com/a/Products/ej/36.html
The driver works flawlessly as soon as the new PID (0x5512) is added to
it.
Signed-off-by: Jan-Niklas Burfeind <kernel@aiyionpri.me>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
