IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 8310b77b48c5558c140e7a57a702e7819e62f04e upstream.
Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating
error leaves the full batch in an ambiguous state as far as the caller
is concerned. Instead flags respective slots as bad, unmapping what
was mapped there right away.
HYPERVISOR_grant_table_op()'s return value and the individual unmap
slots' status fields get used only for a one-time - there's not much we
can do in case of a failure.
Note that there's no GNTST_enomem or alike, so GNTST_general_error gets
used.
The map ops' handle fields get overwritten just to be on the safe side.
This is part of XSA-367.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/96cccf5d-e756-5f53-b91a-ea269bfb9be0@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3fbd7ec62dec1528fb8044034e2885f2b257941 upstream.
This is arm port of commit 6a5022a56ac3 ("kprobes/x86: Allow to
handle reentered kprobe on single-stepping")
Since the FIQ handlers can interrupt in the single stepping
(or preparing the single stepping, do_debug etc.), we should
consider a kprobe is hit in the NMI handler. Even in that
case, the kprobe is allowed to be reentered as same as the
kprobes hit in kprobe handlers
(KPROBE_HIT_ACTIVE or KPROBE_HIT_SSDONE).
The real issue will happen when a kprobe hit while another
reentered kprobe is processing (KPROBE_REENTER), because
we already consumed a saved-area for the previous kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Fixes: 24ba613c9d6c ("ARM kprobes: core code")
Cc: stable@vger.kernel.org #v2.6.25~v4.11
Signed-off-by: huangshaobo <huangshaobo6@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2acb909750431030b65a0a2a17fd8afcbd813a84 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448dfa78e3e58186c934449aaf6d49b50 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a442600b006ef7dec3a6dc98bcf59c6 ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb8878 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac8893c4fa3d4a34915dc5cdab568a39db5086c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 1fed2252713e ("ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467cb8657cf8b5e610a30a4c502085e4f9 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb0a ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36bf1dfb8b266e089afa9b7b984217f17027bf35 upstream.
set_phys_to_machine can fail due to lack of memory, see the kzalloc call
in arch/arm/xen/p2m.c:__set_phys_to_machine_multi.
Don't ignore the potential return error in set_foreign_p2m_mapping,
returning it to the caller instead.
This is part of XSA-361.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Cc: stable@vger.kernel.org
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]
This reverts commit c17e9377aa81664d94b4f2102559fcf2a01ec8e7.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 39d3454c3513840eb123b3913fda6903e45ce671 upstream.
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a88afa46b86ff461c89cc33fc3a45267fff053e8 upstream.
When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).
It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.
Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Fixes: df595746fa69 ("ARM: imx: add suspend in ocram support for i.mx6q")
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bac717171971176b78c72d15a8b6961764ab197f ]
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ec76c2eea903947202098090bbe07a739b5246e9 upstream.
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c04 ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6d5 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 851a95da583c26e2ddeb7281e9b61f0d76ea5aba ]
The triggers for the ADC were taken from at91sam9260 dtsi but are not
correct.
Fixes: a4c1d6c75822 ("ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-10-alexandre.belloni@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1062fa7292f1e3744db0a487c4ac0109e09b03d ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: b7c2b61570798 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-4-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4dd2d448816a27c1446f8f37fce375daf64148 ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 38153a017896f ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-3-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e79f0211b473f8e1eab8211a9fd50cc41a3a061 ]
When running in BE mode on LPAE hardware with a PA-to-VA translation
that exceeds 4 GB, we patch bits 39:32 of the offset into the wrong
byte of the opcode. So fix that, by rotating the offset in r0 to the
right by 8 bits, which will put the 8-bit immediate in bits 31:24.
Note that this will also move bit #22 in its correct place when
applying the rotation to the constant #0x400000.
Fixes: d9a790df8e984 ("ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE")
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bd7e7ff56feea7810df900fb09c9741d259861d9 upstream.
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c750b ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d992fd8f4e0f09c980726308d2f2725587b32d6 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb0896562228 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecc1ff532b499d20304a4f682247137025814c34 upstream.
On Odroid XU board the USB3-0 port is a microUSB and USB3-1 port is USB
type A (host). The roles were copied from Odroid XU3 (Exynos5422)
design which has it reversed.
Fixes: 8149afe4dbf9 ("ARM: dts: exynos: Add initial support for Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-1-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33d0d843872c5ddbe28457a92fc6f2487315fb9f ]
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e135 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dea252fa41cd8ce332d148444e4799235a8a03ec ]
When running dtbs_check thermal_zone warn about the
temperature declared.
thermal-zones: cpu-thermal:trips:cpu-alert0:temperature:0:0: 850000 is greater than the maximum of 200000
It's indeed wrong the real value is 85°C and not 850°C.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201003100332.431178-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f6d7cde84f6c5551586c8b9b68d70f8e6dc9a000 upstream.
Commit f6361c6b3880 ("ARM: S3C24XX: remove separate restart code")
removed usage of the watchdog reset platform code in favor of the
Samsung SoC watchdog driver. However the latter was not selected thus
S3C24xx platforms lost reset abilities.
Cc: <stable@vger.kernel.org>
Fixes: f6361c6b3880 ("ARM: S3C24XX: remove separate restart code")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7be0d19c751b02db778ca95e3274d5ea7f31891c upstream.
Selecting CONFIG_SAMSUNG_PM_DEBUG (depending on CONFIG_DEBUG_LL) but
without CONFIG_MMU leads to build errors:
arch/arm/plat-samsung/pm-debug.c: In function ‘s3c_pm_uart_base’:
arch/arm/plat-samsung/pm-debug.c:57:2: error:
implicit declaration of function ‘debug_ll_addr’ [-Werror=implicit-function-declaration]
Fixes: 99b2fc2b8b40 ("ARM: SAMSUNG: Use debug_ll_addr() to get UART base address")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200910154150.3318-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c17a2974abf68a58517f75741b15c4aba42b4b8 ]
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb98fff84ad1ea321823759edaba573a16fa02bd ]
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea4e792f3c8931fffec4d700cf6197d84e9f35a6 ]
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22c9e58299e5f18274788ce54c03d4fb761e3c5d ]
This is commit fdfeff0f9e3d ("arm64: hw_breakpoint: Handle inexact
watchpoint addresses") but ported to arm32, which has the same
problem.
This problem was found by Android CTS tests, notably the
"watchpoint_imprecise" test [1]. I tested locally against a copycat
(simplified) version of the test though.
[1] https://android.googlesource.com/platform/bionic/+/master/tests/sys_ptrace_test.cpp
Link: https://lkml.kernel.org/r/20191019111216.1.I82eae759ca6dc28a245b043f485ca490e3015321@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e007b367a59bcdf484c81f6df9bd5a4cc179ca6 ]
The L310_PREFETCH_CTRL register bits 28 and 29 to enable data and
instruction prefetch respectively can also be accessed via the
L2X0_AUX_CTRL register. They appear to be actually wired together in
hardware between the registers. Changing them in the prefetch
register only will get undone when restoring the aux control register
later on. For this reason, set these bits in both registers during
initialisation according to the devicetree property values.
Link: https://lore.kernel.org/lkml/76f2f3ad5e77e356e0a5b99ceee1e774a2842c25.1597061474.git.guillaume.tucker@collabora.com/
Fixes: ec3bd0e68a67 ("ARM: 8391/1: l2c: add options to overwrite prefetching behavior")
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Upstream commits fdfe7cbd5880 ("KVM: Pass MMU notifier range flags to
kvm_unmap_hva_range()") and b5331379bc62 ("KVM: arm64: Only reschedule
if MMU_NOTIFIER_RANGE_BLOCKABLE is not set") fix a "sleeping from invalid
context" BUG caused by unmap_stage2_range() attempting to reschedule when
called on the OOM path.
Unfortunately, these patches rely on the MMU notifier callback being
passed knowledge about whether or not blocking is permitted, which was
introduced in 4.19. Rather than backport this considerable amount of
infrastructure just for KVM on arm, instead just remove the conditional
reschedule.
Cc: <stable@vger.kernel.org> # v4.9 only
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d5ec9b39f8b31d98f65bc5577b5d15d93795d7 upstream.
Since clang does not push pc and sp in function prologues, the current
implementation of unwind_frame does not work. By using the previous
frame's lr/fp instead of saved pc/sp we get valid unwinds on clang-built
kernels.
The bounds check on next frame pointer must be changed as well since
there are 8 less bytes between frames.
This fixes /proc/<pid>/stack.
Link: https://github.com/ClangBuiltLinux/linux/issues/912
Reported-by: Miles Chen <miles.chen@mediatek.com>
Tested-by: Miles Chen <miles.chen@mediatek.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ad7b4e8f89d6bcc9887ca701cf2745a6aedb1a0 ]
if of_find_device_by_node() succeed, socfpga_setup_ocram_self_refresh
doesn't have a corresponding put_device(). Thus add a jump target to
fix the exception handling for this function implementation.
Fixes: 44fd8c7d4005 ("ARM: socfpga: support suspend to ram")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f87a4f022c44e5b87e842a9f3e644fba87e8385f ]
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e467905596 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aa54ea903abb02303bf55855fb51e3fcee135d70 upstream.
Fix build error for the case:
defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
config: keystone_defconfig
CC arch/arm/kernel/signal.o
In file included from ../include/linux/random.h:14,
from ../arch/arm/kernel/signal.c:8:
../arch/arm/include/asm/percpu.h: In function ‘__my_cpu_offset’:
../arch/arm/include/asm/percpu.h:29:34: error: ‘current_stack_pointer’ undeclared (first use in this function); did you mean ‘user_stack_pointer’?
: "Q" (*(const unsigned long *)current_stack_pointer));
^~~~~~~~~~~~~~~~~~~~~
user_stack_pointer
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eec13b42d41b0f3339dcf0c4da43734427c68620 upstream.
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire
unexpectedly. In such cases, the hw_breakpoint logic will invoke the user
overflow handler which will typically raise a SIGTRAP back to the current
task. This is futile when returning back to the kernel because (a) the
signal won't have been delivered and (b) userspace can't handle the thing
anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
Cc: <stable@vger.kernel.org>
Fixes: f81ef4a920c8 ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework")
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4845446036fc9c13f43b54a65c9b757c14f5141b ]
if of_find_device_by_node() succeed, imx6q_suspend_init() doesn't have a
corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 586745f1598ccf71b0a5a6df2222dee0a865954e ]
if of_find_device_by_node() succeed, imx_suspend_alloc_ocram() doesn't
have a corresponding put_device(). Thus add a jump target to fix the
exception handling for this function implementation.
Fixes: 1579c7b9fe01 ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2854bbe5f5c4b4bec8061caf4f2e603d8819446 ]
The CMA and DMA_CMA Kconfig options need to be selected
by the Integrator in order to produce boot console on some
Integrator systems.
The REGULATOR and REGULATOR_FIXED_VOLTAGE need to be
selected in order to boot the system from an external
MMC card when using MMCI/PL181 from the device tree
probe path.
Select these things directly from the Kconfig so we are
sure to be able to bring the systems up with console
from any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35509737c8f958944e059d501255a0bf18361ba0 upstream.
The PL310 Auxiliary Control Register shouldn't have the "Full line of
zero" optimization bit being set before L2 cache is enabled. The L2X0
driver takes care of enabling the optimization by itself.
This patch fixes a noisy error message on Tegra20 and Tegra30 telling
that cache optimization is erroneously enabled without enabling it for
the CPU:
L2C-310: enabling full line of zeros but not enabled in Cortex-A9
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1de94380af588bdf6ad6f0cc1f75004c35bc096 ]
Recent work with KASan exposed the folling hard-coded bitmask
in arch/arm/mm/proc-macros.S:
bic rd, sp, #8128
bic rd, rd, #63
This forms the bitmask 0x1FFF that is coinciding with
(PAGE_SIZE << THREAD_SIZE_ORDER) - 1, this code was assuming
that THREAD_SIZE is always 8K (8192).
As KASan was increasing THREAD_SIZE_ORDER to 2, I ran into
this bug.
Fix it by this little oneline suggested by Ard:
bic rd, sp, #(THREAD_SIZE - 1) & ~63
Where THREAD_SIZE is defined using THREAD_SIZE_ORDER.
We have to also include <linux/const.h> since the THREAD_SIZE
expands to use the _AC() macro.
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3866f217aaa81bf7165c7f27362eee5d7919c496 ]
call_undef_hook() in traps.c applies the same instr_mask for both 16-bit
and 32-bit thumb instructions. If instr_mask then is only 16 bits wide
(0xffff as opposed to 0xffffffff), the first half-word of 32-bit thumb
instructions will be masked out. This makes the function match 32-bit
thumb instructions where the second half-word is equal to instr_val,
regardless of the first half-word.
The result in this case is that all undefined 32-bit thumb instructions
with the second half-word equal to 0xde01 (udf #1) work as breakpoints
and will raise a SIGTRAP instead of a SIGILL, instead of just the one
intended 16-bit instruction. An example of such an instruction is
0xeaa0de01, which is unallocated according to Arm ARM and should raise a
SIGILL, but instead raises a SIGTRAP.
This patch fixes the issue by setting all the bits in instr_mask, which
will still match the intended 16-bit thumb instruction (where the
upper half is always 0), but not any 32-bit thumb instructions.
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 665e7c73a7724a393b4ec92d1ae1e029925ef2b7 ]
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e26dead442689a861358f33126210b0f8de615a9 ]
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d0c7bb20c083a6e810d2142545b5606f8131080 ]
The IPU that drives HDMI must have its pre_sel set to pll2_pfd_396m
to avoid stepping on the LVDS output's toes, as the PLL can't be clocked
to the pixel clock and to the LVDS serial clock (3.5*pixel clock) at the
same time.
As we are using ipu1_di0 and ipu2_di0, ensure both are switched to
to pll2_pfd2_396m to avoid issues. The LDB driver will switch the
required IPU to ldb_di1 when it uses it to drive LVDS.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8101b5a1531f3390b3a69fa7934c70a8fd6566ad ]
Stephen reported the following build warning on a ARM multi_v7_defconfig
build with GCC 9.2.1:
kernel/futex.c: In function 'do_futex':
kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized]
1676 | return oldval == cmparg;
| ~~~~~~~^~~~~~~~~
kernel/futex.c:1652:6: note: 'oldval' was declared here
1652 | int oldval, ret;
| ^~~~~~
introduced by commit a08971e9488d ("futex: arch_futex_atomic_op_inuser()
calling conventions change").
While that change should not make any difference it confuses GCC which
fails to work out that oldval is not referenced when the return value is
not zero.
GCC fails to properly analyze arch_futex_atomic_op_inuser(). It's not the
early return, the issue is with the assembly macros. GCC fails to detect
that those either set 'ret' to 0 and set oldval or set 'ret' to -EFAULT
which makes oldval uninteresting. The store to the callsite supplied oldval
pointer is conditional on ret == 0.
The straight forward way to solve this is to make the store unconditional.
Aside of addressing the build warning this makes sense anyway because it
removes the conditional from the fastpath. In the error case the stored
value is uninteresting and the extra store does not matter at all.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/87pncao2ph.fsf@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e47cb97f153193d4b41ca8d48127da14513d54c7 upstream.
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf345e2e ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f739fdfe9e5ce668bd6d3210f310df282321837 upstream.
The R-Mobile APE6 Compare Match Timer 1 generates 8 interrupts, one for
each channel, but currently only 1 is described.
Fix this by adding the missing interrupts.
Fixes: f7b65230019b9dac ("ARM: shmobile: r8a73a4: Add CMT1 node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200408090926.25201-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0caf34350a25907515d929a9c77b9b206aac6d1e upstream.
The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b432a ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
