IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 34138a59b9 upstream.
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3bb0f796f ]
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25bdae0f1c ]
Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to
match its behaviour with SCLK clock for AUD_I2S (I2S0) device until
a proper fix for Exynos I2S driver is ready.
This fixes the following synchronous abort issue revealed by the probe
order change caused by the commit 93d2e4322a ("of: platform: Batch
fwnode parsing when adding all top level devices")
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701
Hardware name: Samsung TM2E board (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : samsung_i2s_probe+0x768/0x8f0
lr : samsung_i2s_probe+0x688/0x8f0
...
Call trace:
samsung_i2s_probe+0x768/0x8f0
platform_drv_probe+0x50/0xa8
really_probe+0x108/0x370
driver_probe_device+0x54/0xb8
__device_attach_driver+0x90/0xc0
bus_for_each_drv+0x70/0xc8
__device_attach+0xdc/0x140
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
deferred_probe_work_func+0x70/0xa8
process_one_work+0x2a8/0x718
worker_thread+0x48/0x470
kthread+0x134/0x160
ret_from_fork+0x10/0x1c
Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00)
---[ end trace ccf721c9400ddbd6 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee82eb953 ]
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e21be0d1d7 upstream.
Save and restore top PLL related configuration registers for big (APLL)
and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks
were reset to default values after suspend/resume cycle and performance
after system resume was affected when performance governor has been selected.
Fixes: 773424326b ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9323b664c ]
Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.
Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes: 773424326b ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1da220e3a5 ]
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07c1a0f68 ]
The TOP "aclk400_mscl" clock should be kept enabled all the time
to allow proper access to power management control for MSC power
domain and devices that are a part of it. This change is required
for the scaler to work properly after domain power on/off sequence.
Fixes: 318fa46cc6 ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8321e7887 ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ac051eeab ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab0447845c ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdb68fbd4e ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e4db0c283 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 179db533c0 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ccb58968b ]
Add missing identifiers for phyclk_mipidphy0_bitclkdiv8_phy and
phyclk_mipidphy0_rxclkesc0_phy clocks. Access to those clocks is needed
to setup initial clock configuration for display subsystem in device tree
in order to avoid dependency on the configuration left by the bootloader.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 318fa46cc6 ]
Some parent clocks of the Exynos542x clock blocks, which have separate
power domains (like DISP, MFC, MSC, GSC, FSYS and G2D) must be always
enabled to access any register related to power management unit or devices
connected to it. For the time being, until a proper solution based on
runtime PM is applied, mark those clocks as critical (instead of ignore
unused or even no flags) to prevent disabling them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> [Exynos5800 Peach Pi Chromebook]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exynos PMU node is an interrupt, clock and PMU (Power Management Unit)
controller, and these functionalities are supported by different drivers
that matches the same compatible strings.
Since commit 989eafd0b6 ("clk: core: Avoid double initialization of
clocks") the OF core flags clock controllers registered with the
CLK_OF_DECLARE() macro as OF_POPULATED, so platform devices with the same
compatible string will not be registered.
This prevents the PMU platform device to be created, so the Exynos PMU
driver is never probed. This breaks (among other things) Suspend-to-RAM.
Fix this by changing CLKOUT driver initialization method to
CLK_OF_DECLARE_DRIVER(), which doesn't clear the OF_POPULATED flag, so
later a platform device is created and the Exynos PMU platform driver
can be be probed properly.
Fixes: 989eafd0b6 ("clk: core: Avoid double initialization of clocks")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
After this patch:
$ modinfo drivers/clk/samsung/clk-exynos-audss.ko | grep alias
alias: platform:exynos-audss-clk
alias: of:N*T*Csamsung,exynos5420-audss-clockC*
alias: of:N*T*Csamsung,exynos5420-audss-clock
alias: of:N*T*Csamsung,exynos5410-audss-clockC*
alias: of:N*T*Csamsung,exynos5410-audss-clock
alias: of:N*T*Csamsung,exynos5250-audss-clockC*
alias: of:N*T*Csamsung,exynos5250-audss-clock
alias: of:N*T*Csamsung,exynos4210-audss-clockC*
alias: of:N*T*Csamsung,exynos4210-audss-clock
Fixes: 4d252fd571 ("clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds code instantiating the EPLL, which is used as the
audio subsystem's root clock.
The requirement to specify the external root clock in clocks property
is documented. Having the consumer 'clocks' property ensures proper
initialization order by explicitly specifying dependencies in DT.
It prevents situations when the SoC's clock controller driver has
initialized, the external oscillator clock is not yet registered
and setting clock frequencies through assigned-clock-rates property
doesn't work properly due to unknown external oscillator frequency.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no need to log probe() completion in normal conditions
so the "setup completed" log is removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5410 Audio Subsystem Clock Controller, comparing to the already
supported IP block revisions, has additionally an I2S_MST divider
so a new compatible string is added.
It is not clear from the Exynos5410 User's Manual released on 2012.03.09
where in the clock tree the I2S_MST clock divider can be found exactly
so this clock is left unimplemented for now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
There is no such significant differences in pll2550x PLL type
to justify a separate registration function. This patch adapts
exynos5440 driver to use the common function and removes
samsung_clk_register_pll2550x().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the mux/divider clocks for CMU_CDREX (DRAM Express
Controller) which generates the clocks for DRAM and NoC (Network on Chip)
bus. There is differnet source of MUX_MX_MSPLL_CCORE between exynos5420
and exynos5422, so each MUX_MX_MSPLL_CCORE uses the different parent source
group.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch uses the samsung_cmu_register_one() to simplify code
and move the pll/mux/div/gate data to initconst section.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch moves the samsung_cmu_info struct instances to initconst
section, this decreases the kernel image size by 784 bytes, which makes
zImage smaller by 480 bytes.
The patch increases .init.rodata section size by 780 bytes but decreases
.init.text section size by 1564 bytes.
Size of the drivers/clk/samsung/clk-exynos5260.o object file is 29100
bytes without the patch and 28316 after applying the patch.
The section size differences are as below:
15c15
< 3 .init.text 000006b8 00000000 00000000 00000034 2**2
---
> 3 .init.text 0000009c 00000000 00000000 00000034 2**2
25c25
< 8 .init.rodata 00003f6c 00000000 00000000 00002f20 2**2
---
> 8 .init.rodata 00004278 00000000 00000000 00002904 2**2
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-s5pv210/Kconfig:config ARCH_S5PV210
arch/arm/mach-s5pv210/Kconfig: bool "Samsung S5PV210/S5PC110" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since this code is already not using module_init, case, the init
ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tags etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-8-paul.gortmaker@windriver.com
This patch adds the CLK_IGNORE_UNUSED flag for PCI Express's clocks
which need to remain enabled. The 'pcie' gate clock definition is
also added.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some clocks are required to be unmasked during suspend to RAM. Otherwise
the PMU will stuck and the power down sequence will never be completed.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds CLK_IGNORE_UNUSED flag for sclk_aud_uart gate
clock for uart3 operation.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki@samsung.com: edited the patch's summary]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use the byte-order aware big endian accessors, allowing for kernels
running under big-endian.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fix the clk endian access code to deal with kernels built for big endian
operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5433 uses different register layout for CPU clock registers
than earlier SoCs so add new code for handling this layout. Also
add new CLK_CPU_HAS_E5433_REGS_LAYOUT flag to request using it.
There should be no functional change resulting from this patch.
Cc: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Open-code samsung_cmu_register_one() calls for CMU_APOLLO and
CMU_ATLAS setup code as a preparation for adding CPU clocks
support for Exynos5433.
There should be no functional change resulting from this patch.
Cc: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Although unbinding a driver requires root privileges but it still might
be used theoretically in certain attacks (by triggering NULL pointer
exception or memory corruption if driver does not provide proper remove
callbacks or core does not handle it).
Samsung clock drivers are essential for system operation so their
removal is not expected. More over, the Exynos3250 ISP clock driver does
not implement remove() driver callback and it is not buildable as
modules.
Suppress the unbind interface for Exynos3250 ISP and S3C2410 DCLK clock
drivers.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The aclk333 clock needs to be ungated during the MFC power domain switch,
so set the clock ID to allow the Exynos power domain logic to lookup this
clock if is defined in the MFC PD device tree node.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Just like other Exynos5 family SoCs, this one has four UARTs. Add
missing UART3 clocks to the Exynos5410 clock driver.
Add clocks for USB and PWM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The arrays with initialization data of PLLs can be moved to initconst
section because they are referenced only from other initconst-level
symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The PNAME macro defines array of strings for names of mux parents.
Although the strings itself were const but pointers to them were not thus
this data resided in initdata. Make this an array of const pointers to
const strings and move to initconst section.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The exynos5250_clk_sleep_init() function can be moved to init section
because it is referenced only from other init-level calls.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The exynos5420_clk_sleep_init() function and arrays with initialization
data of PLLs can be moved to init section because they are referenced
only from other init-level symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The arrays with initialization data of PLLs can be moved to initconst
section because they are referenced only from other initconst-level
symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
