IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit bd8963e602c77adc76dbbbfc3417c3cf14fed76b upstream.
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a22aabf20adf89cb216f566913196128766f25b ]
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d44 ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d366c2f9df8279df2adbb60471f86fc40a1c39e ]
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598cdc ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5de717974005fcad2502281e9f82e139ca91f4bb ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9495b9b31abe525ebd93da58de2c88b9f66d3a0e ]
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 834cea3a252ed4847db076a769ad9efe06afe2d5 upstream.
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d52097010078c1844348dc0e467305e5f90fd317 ]
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe82cf92cd4825c3029434cabfcd2f1780e64be ]
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit effa453168a7eeb8a562ff4edc1dbf9067360a61 ]
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f98960c046ee1136e7096aee168eda03aef8a5d ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372e4 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6840a5e370b7ea4fde16ce2caf431bcc87f9a75 ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec97853f ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1299505162ad00def3573260c2c68b9c8e8d697 ]
When adding the code to handle platform_get_irq*() errors in the commit
489447380a29 ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a29 ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16a3bb69aa6baabf8f0aca982c8cf21e2a4f6bc ]
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab18c ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 86ff25ed6cd8240d18df58930bd8848b19fce308 upstream.
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b64210f2f7c11c757432ba3701d88241b2b98fb1 ]
If an i2c client receives an interrupt during reboot or shutdown it may
be too late to service it by making an i2c transaction on the bus
because the i2c controller has already been shutdown. This can lead to
system hangs if the i2c controller tries to make a transfer that is
doomed to fail because the access to the i2c pins is already shut down,
or an iommu translation has been torn down so i2c controller register
access doesn't work.
Let's simply disable the irq if there isn't a shutdown callback for an
i2c client when there is an irq associated with the device. This will
make sure that irqs don't come in later than the time that we can handle
it. We don't do this if the i2c client device already has a shutdown
callback because presumably they're doing the right thing and quieting
the device so irqs don't come in after the shutdown callback returns.
Reported-by: kernel test robot <lkp@intel.com>
[swboyd@chromium.org: Dropped newline, added commit text, added
interrupt.h for robot build error]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ca070ef0dd885616ef294d269a9bf8e3b258e1a upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com
Fixes: 83e53a8f120f ("i2c: Add bus driver for for OSIF USB i2c device.")
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f0cdec8b5fd94135d643662506ee94ae9e98785 ]
The P2040/P2041 has an erratum where the normal i2c recovery mechanism
does not work. Implement the alternative recovery mechanism documented
in the P2040 Chip Errata Rev Q.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65171b2df15eb7545431d75c2729b5062da89b43 ]
Move the existing calls of mpc_i2c_fixup() to a recovery function
registered via bus_recovery_info. This makes it more obvious that
recovery is supported and allows for a future where recovery is
triggered by the i2c core.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24990423267ec283b9d86f07f362b753eb9b0ed5 upstream.
Interrupt handler processes multiple message write requests one after
another, till the driver message queue is drained. However if driver
encounters a read message without preceding START, it stops the I2C
transfer as it is an invalid condition for the controller. At least the
comment describes a requirement "the controller forces us to send a new
START when we change direction". This stop results in clearing the
message queue (i2c->msg = NULL).
The code however immediately jumped back to label "retry_write" which
dereferenced the "i2c->msg" making it a possible NULL pointer
dereference.
The Coverity analysis:
1. Condition !is_msgend(i2c), taking false branch.
if (!is_msgend(i2c)) {
2. Condition !is_lastmsg(i2c), taking true branch.
} else if (!is_lastmsg(i2c)) {
3. Condition i2c->msg->flags & 1, taking true branch.
if (i2c->msg->flags & I2C_M_RD) {
4. write_zero_model: Passing i2c to s3c24xx_i2c_stop, which sets i2c->msg to NULL.
s3c24xx_i2c_stop(i2c, -EINVAL);
5. Jumping to label retry_write.
goto retry_write;
6. var_deref_model: Passing i2c to is_msgend, which dereferences null i2c->msg.
if (!is_msgend(i2c)) {"
All previous calls to s3c24xx_i2c_stop() in this interrupt service
routine are followed by jumping to end of function (acknowledging
the interrupt and returning). This seems a reasonable choice also here
since message buffer was entirely emptied.
Addresses-Coverity: Explicit null dereferenced
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92dfb27240fea2776f61c5422472cb6defca7767 ]
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
Fixes: e5b2e3e74201 ("i2c: sh7760: add IRQ check")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b2e3e742015dd2aa6bc7bcef2cb59b2de1221c ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: a26c20b1fa6d ("i2c: Renesas SH7760 I2C master driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e5f7a8d931fb4beba245bdbc94734175fda9de ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6129c32867baa7988f7fd2066cf18ed662d240 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: 5faf6e1f58b4 ("i2c: emev2: add driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5581c2c5d02bc63a0edb53e061c8e97cd490646e ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1858ce0cfe31368b23ba55794e409fb57ced4a4 ]
The brcmstb_send_i2c_cmd currently has a condition that is (CMD_RD ||
CMD_WR) which always evaluates to true, while the obvious fix is to test
whether the cmd variable passed as parameter holds one of these two
values.
Fixes: dd1aa2524bc5 ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2cfa2d1dbdcc3b6dba1ecb7026a537a1d7277f ]
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337dd ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1de67a3dee7a279ebe4d892b359fe3696938ec15 upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f70a876c2e78e58c5ca0bbf0547e4f6d upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbe4d69d252e9e65c6c46826980b77b11a142065 upstream.
The spec for the pca9546 was missing. This chip is the same as the pca9545
except that it lacks interrupt lines. While the i2c_device_id table mapped
the pca9546 to the pca9545 definition the compatible table did not.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Peter Rosin <peda@axentia.se>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e4f0b85be308a01b830c5fbdffc657e1a6dd0 upstream
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf30 ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90ad2cbe88c22d0215225ab9594eeead0eb24fde upstream
Instead of repeatedly calling clk_get_rate for each transfer, register
a clock notifier to update the cached divider value each time the clock
rate actually changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bd970aa62f2f7f80fd0d212b1d4ccea5df4aed ]
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21653a4181ff292480599dad996a2b759ccf050f ]
Some ACPI i2c-devices _STA method (which is used to detect if the device
is present) use autodetection code which probes which device is present
over i2c. This requires the I2C ACPI OpRegion handler to be registered
before we enumerate i2c-clients under the i2c-adapter.
This fixes the i2c touchpad on the Lenovo ThinkBook 14-IIL and
ThinkBook 15 IIL not getting an i2c-client instantiated and thus not
working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1842039
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a355aeb24081e4538d4d424cd189f16c0bbd983 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 914a7b3563b8fb92f976619bbd0fa3a4a708baae ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314139f9f0abdba61ed9a8463bbcb0bf900ac5a2 ]
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db9254d6b896b587759e2c844c277fb1a6da5b9 ]
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd217f2300793a106b49c7dfcbfb26e348bc7593 ]
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ]
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ]
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ]
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1413ef638abae4ab5621901cf4d8ef08a4a48ba6 ]
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7fda ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7fda to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9d1a0a41d4486955e96552293c1fcf1fce61602 ]
A call to 'i2c_demux_deactivate_master()' is missing in the error handling
path, as already done in the remove function.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e1b9f99ff8c40bba6e59de9ad4a659447b1e4112 upstream.
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
