IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 39a72dbfe188291b156dd6523511e3d5761ce775 upstream.
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
Fixes: ce69d37b7d8f ("mmc: core: Prevent violation of specs while initializing cards")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9972e6b404884adae9eec7463e30d9b3c9a70b18 upstream.
SDIO tuple is only allocated for standard SDIO card, especially it causes
memory corruption issues when the non-standard SDIO card has removed, which
is because the card device's reference counter does not increase for it at
sdio_init_func(), but all SDIO card device reference counter gets decreased
at sdio_release_func().
Fixes: 6f51be3d37df ("sdio: allow non-standard SDIO cards")
Signed-off-by: Matthew Ma <mahongwei@zeku.com>
Reviewed-by: Weizhao Ouyang <ouyangweizhao@zeku.com>
Reviewed-by: John Wang <wangdayu@zeku.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221014034951.2300386-1-ouyangweizhao@zeku.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cbedf52608cc3cbc1c2a9a861fb671620427a20 ]
If clk_prepare_enable() fails, there is no point in calling
clk_disable_unprepare() in the error handling path.
Move the out_clk label at the right place.
Fixes: b6507596dfd6 ("MIPS: Alchemy: au1xmmc: use clk framework")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/21d99886d07fa7fcbec74992657dabad98c935c4.1661412818.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35ca91d1338ae158f6dcc0de5d1e86197924ffda upstream.
According to the datasheet [1] at page 377, 4-bit bus width is turned on by
bit 2 of the Bus Width Register. Thus the current bitmask is wrong: define
BUS_WIDTH_4 BIT(1)
BIT(1) does not work but BIT(2) works. This has been verified on real MOXA
hardware with FTSDC010 controller revision 1_6_0.
The corrected value of BUS_WIDTH_4 mask collides with: define BUS_WIDTH_8
BIT(2). Additionally, 8-bit bus width mode isn't supported according to the
datasheet, so let's remove the corresponding code.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220907205753.1577434-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 533a6cfe08f96a7b5c65e06d20916d552c11b256 upstream
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[kamal: Drop non-existent hunks in 4.9's __mmc_switch]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad91619aa9d78ab1c6d4a969c3db68bc331ae76c upstream
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24ed3bd01d6a844fd5e8a75f48d0a3d10ed71bf9 upstream
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[kamal: Drop mmc_run_bkops hunk, non-existent]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f311c94aabdb419c28e3147bcc8ab89269f1a7e upstream.
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6c9219ca1139b74541b2a98cee47a3426d754a9 ]
Even if the current WARN() notifies the user that something is severely
wrong, we can still end up in a PANIC() when trying to invoke the missing
->enable_sdio_irq() ops. Therefore, let's also return an error code and
prevent the host from being added.
While at it, move the code into a separate function to prepare for
subsequent changes and for further host caps validations.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bd2db32e7c3e35bd4d9b8bbff689434a50893546 upstream.
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: Xin Xiong <xiongx18@fudan.edu.cn>
Cc: Xin Tan <tanxin.ctf@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Cc: linux-mmc@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Reported-by: whitehat002 <hackyzh002@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce5f6c2c9b0fcb4094f8e162cfd37fb4294204f7 ]
The 'reg_vmmc' regulator is enabled in the probe. It is never disabled.
Neither in the error handling path of the probe nor in the remove
function.
Register a devm_action to disable it when needed.
Fixes: 4dc5a79f1350 ("mmc: mxs-mmc: enable regulator for mmc slot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162079f2dccd02cb4b6654defd32ca387dd6d4d4 ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 43592c8736e84025d7a45e61a46c3fa40536a364 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 697542bceae51f7620af333b065dd09d213629fb upstream.
Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Cc: stable@vger.kernel.org
Fixes: c537a1c5ff63 ("mmc: dw_mmc: exynos: add variable delay tuning sequence")
Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c8171929116cc23f74743d99251eedadf62341a upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025115608.5287-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3ff0189d3bc9c03845fe37472c140f0fefd0c79 ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f8203b4be1937c4939bb98623e67dcfd7da4d1 ]
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13c3c081845b51e8ba71a90e91c52679cfdbf89 ]
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 77347eda64ed5c9383961d1de9165f9d0b7d8df6 upstream.
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0244847f9fc5e20df8b7483c8a4717fe0432d38 upstream.
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0bb3107703d2c58f7a0a7a2060bb57bc120326 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f9ae69e5267f53e89e296fccee291975a85f0eb ]
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 917a5336f2c27928be270226ab374ed0cbf3805d upstream.
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ]
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ]
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f92e04f764b86e55e522988e6f4b6082d19a2721 upstream.
When analysing tuples fails we may loop indefinitely to retry. Let's avoid
this by using a 10s timeout and bail if not completed earlier.
Signed-off-by: Fengnan Chang <fengnanchang@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210123033230.36442-1-fengnanchang@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87d7ad089b318b4f319bf57f1daa64eb6d1d10ad ]
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ebe2607965d3e2dc02029e8c7dd35fbe508ffd0 ]
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1194be8c949b8190b2882ad8335a5d98aa50c735 ]
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: d87fc9663688 ("mmc: sdhci-esdhc-imx: support setting tuning start point")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 53dd0a7cd65edc83b0c243d1c08377c8b876b2ee upstream.
SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least
SAMA5D27 doesn't). Fix this by forcing card-detect in the module
if module-controlled CD is not used.
Fixed commit addresses the problem only for non-removable cards. This
amends it to also cover gpio-cd case.
Cc: stable@vger.kernel.org
Fixes: 7a1e3f143176 ("mmc: sdhci-of-at91: force card detect value for non removable devices")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af3ed119329cf9690598c5a562d95dfd128e91d6 upstream.
The code in mmc_spi_initsequence() tries to send a burst with
high chipselect and for this reason hardcodes the device into
SPI_CS_HIGH.
This is not good because the SPI_CS_HIGH flag indicates
logical "asserted" CS not always the physical level. In
some cases the signal is inverted in the GPIO library and
in that case SPI_CS_HIGH is already set, and enforcing
SPI_CS_HIGH again will actually drive it low.
Instead of hard-coding this, toggle the polarity so if the
default is LOW it goes high to assert chipselect but if it
is already high then toggle it low instead.
Cc: Phil Elwell <phil@raspberrypi.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a187d03352086e300daa2044051db00044cd171 upstream.
For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:
mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]
The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.
Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode")
Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present
Cc: <stable@vger.kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e20186e706da8446f9435f2924cd65ab1397e73 ]
We need to handle mmc_of_parse() errors during probe otherwise the
MMC driver could start without proper initialization (e.g. power sequence).
Fixes: 476bf3d62d5c ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe0acab448f68c3146235afe03fb932e242ec94c upstream.
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream.
This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c91843463e9e821dc3b48fe37e3155fa38299f6e ]
Isolated initially to renesas_sdhi_internal_dmac [1], Ulf suggested
adding MMC_CAP_ERASE to the TMIO mmc core:
On Fri, Nov 15, 2019 at 10:27:25AM +0100, Ulf Hansson wrote:
-- snip --
This test and due to the discussions with Wolfram and you in this
thread, I would actually suggest that you enable MMC_CAP_ERASE for all
tmio variants, rather than just for this particular one.
In other words, set the cap in tmio_mmc_host_probe() should be fine,
as it seems none of the tmio variants supports HW busy detection at
this point.
-- snip --
Testing on R-Car H3ULCB-KF doesn't reveal any issues (v5.4-rc7):
root@rcar-gen3:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 59.2G 0 disk <--- eMMC
mmcblk0boot0 179:8 0 4M 1 disk
mmcblk0boot1 179:16 0 4M 1 disk
mmcblk1 179:24 0 30G 0 disk <--- SD card
root@rcar-gen3:~# time blkdiscard /dev/mmcblk0
real 0m8.659s
user 0m0.001s
sys 0m1.920s
root@rcar-gen3:~# time blkdiscard /dev/mmcblk1
real 0m1.176s
user 0m0.001s
sys 0m0.124s
[1] https://lore.kernel.org/linux-renesas-soc/20191112134808.23546-1-erosca@de.adit-jv.com/
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Originally-by: Harish Jenny K N <harish_kandiga@mentor.com>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f6498b922e57aecbe3b7fa30a308d9d586c0c369 upstream.
Pandora_wl1251_init_card was used to do special pdata based
setup of the sdio mmc interface. This does no longer work with
v4.7 and later. A fix requires a device tree based mmc3 setup.
Therefore we move the special setup to omap_hsmmc.c instead
of calling some pdata supplied init_card function.
The new code checks for a DT child node compatible to wl1251
so it will not affect other MMC3 use cases.
Generally, this code was and still is a hack and should be
moved to mmc core to e.g. read such properties from optional
DT child nodes.
Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
[Ulf: Fixed up some checkpatch complaints]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ]
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream.
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ]
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
