IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 1bc12d301594eafde0a8529d28d459af81053b3a ]
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3moe6Hz8ELM0iS@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23bc8f69f0eceecbb87c3801d2e48827d2dca92b ]
The pmd_leaf() is used to test a leaf mapped PMD, however, it misses
the PROT_NONE mapped PMD on arm64. Fix it. A real world issue [1]
caused by this was reported by Qian Cai. Also fix pud_leaf().
Link: https://patchwork.kernel.org/comment/24798260/ [1]
Fixes: 8aa82df3c123 ("arm64: mm: add p?d_leaf() definitions")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Link: https://lore.kernel.org/r/20220422060033.48711-1-songmuchun@bytedance.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e377ab82311af95c99648c6424a6b888a0ccb102 ]
Semantics wise, [pud|pmd]_bad() have always implied that a given [PUD|PMD]
entry does not have a pointer to the next level page table. This had been
made clear in the commit a1c76574f345 ("arm64: mm: use *_sect to check for
section maps"). Hence explicitly check for a table entry rather than just
testing a single bit. This basically redefines [pud|pmd]_bad() in terms of
[pud|pmd]_table() making the semantics clear.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1620644871-26280-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2c0b0fbe01419f8f5d1c0b9c581631f34ffce8b ]
The alternatives code must be `noinstr` such that it does not patch itself,
as the cache invalidation is only performed after all the alternatives have
been applied.
Mark patch_alternative() as `noinstr`. Mark branch_insn_requires_update()
and get_alt_insn() with `__always_inline` since they are both only called
through patch_alternative().
Booting a kernel in QEMU TCG with KCSAN=y and ARM64_USE_LSE_ATOMICS=y caused
a boot hang:
[ 0.241121] CPU: All CPU(s) started at EL2
The alternatives code was patching the atomics in __tsan_read4() from LL/SC
atomics to LSE atomics.
The following fragment is using LL/SC atomics in the .text section:
| <__tsan_unaligned_read4+304>: ldxr x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This LL/SC atomic sequence was to be replaced with LSE atomics. However since
the alternatives code was instrumentable, __tsan_read4() was being called after
only the first instruction was replaced, which led to the following code in memory:
| <__tsan_unaligned_read4+304>: ldadd x5, x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This caused an infinite loop as the `stxr` instruction never completed successfully,
so `w7` was always 0.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20220405104733.11476-1-joey.gouly@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 01f6c7338ce267959975da65d86ba34f44d54220 upstream.
Currently the first thing checked is whether the PCSI cpu_suspend function
has been initialized.
Another change will be overloading `acpi_processor_ffh_lpi_probe` and
calling it sooner. So make the `has_lpi` check the first thing checked
to prepare for that change.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4013e26670c590944abdab56c4fa797527b74325 upstream.
On ELF, (NOLOAD) sets the section type to SHT_NOBITS[1]. It is conceptually
inappropriate for .plt and .text.* sections which are always
SHT_PROGBITS.
In GNU ld, if PLT entries are needed, .plt will be SHT_PROGBITS anyway
and (NOLOAD) will be essentially ignored. In ld.lld, since
https://reviews.llvm.org/D118840 ("[ELF] Support (TYPE=<value>) to
customize the output section type"), ld.lld will report a `section type
mismatch` error. Just remove (NOLOAD) to fix the error.
[1] https://lld.llvm.org/ELF/linker_script.html As of today, "The
section should be marked as not loadable" on
https://sourceware.org/binutils/docs/ld/Output-Section-Type.html is
outdated for ELF.
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Fangrui Song <maskray@google.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220218081209.354383-1-maskray@google.com
Signed-off-by: Will Deacon <will@kernel.org>
[nathan: Fix conflicts due to lack of 1cbdf60bd1b7]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a099dbd91e69fcab55eef4be15ed7a8c984918 upstream.
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
Fixes: ae16480785de ("arm64: introduce interfaces to hotpatch kernel and module code")
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220407073323.743224-2-guoren@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 031495635b4668f94e964e037ca93d0d38bfde58 upstream.
The following patches resulted in deferring crash kernel reservation to
mem_init(), mainly aimed at platforms with DMA memory zones (no IOMMU),
in particular Raspberry Pi 4.
commit 1a8e1cef7603 ("arm64: use both ZONE_DMA and ZONE_DMA32")
commit 8424ecdde7df ("arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges")
commit 0a30c53573b0 ("arm64: mm: Move reserve_crashkernel() into mem_init()")
commit 2687275a5843 ("arm64: Force NO_BLOCK_MAPPINGS if crashkernel reservation is required")
Above changes introduced boot slowdown due to linear map creation for
all the memory banks with NO_BLOCK_MAPPINGS, see discussion[1]. The proposed
changes restore crash kernel reservation to earlier behavior thus avoids
slow boot, particularly for platforms with IOMMU (no DMA memory zones).
Tested changes to confirm no ~150ms boot slowdown on our SoC with IOMMU
and 8GB memory. Also tested with ZONE_DMA and/or ZONE_DMA32 configs to confirm
no regression to deferring scheme of crash kernel memory reservation.
In both cases successfully collected kernel crash dump.
[1] https://lore.kernel.org/all/9436d033-579b-55fa-9b00-6f4b661c2dd7@linux.microsoft.com/
Signed-off-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/1646242689-20744-1-git-send-email-vijayb@linux.microsoft.com
[will: Add #ifdef CONFIG_KEXEC_CORE guards to fix 'crashk_res' references in allnoconfig build]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dda7596c109fc382876118627e29db7607cde35d ]
insn_to_jit_off passed to bpf_prog_fill_jited_linfo() is calculated in
instruction granularity instead of bytes granularity, but BPF line info
requires byte offset.
bpf_prog_fill_jited_linfo() will be the last user of ctx.offset before
it is freed, so convert the offset into byte-offset before calling into
bpf_prog_fill_jited_linfo() in order to fix the line info dump on arm64.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220226121906.5709-3-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e4f238b0e9d3670a1612ad900a6e98b2b3f7dd ]
BPF line info needs ctx->offset to be the instruction offset in the whole JITed
image instead of the body itself, so also call build_prologue() first in first
JIT pass.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220226121906.5709-2-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37cbd3c522869247ed4525b5042ff4c6a276c813 ]
A label reference without brackets is a path string, not a phandle as
intended. Add the missing brackets.
Fixes: a5002c41c383 ("arm64: dts: rockchip: add WiFi module support for Firefly-RK3399")
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220304202559.317749-1-robh@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55927cb44db43a57699fa652e2437a91620385dc ]
After converting ahci-platform txt binding to yaml nodename is reported
as not matching the standard:
arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dt.yaml:
ahci@663f2000: $nodename:0: 'ahci@663f2000' does not match '^sata(@.*)?$'
Fix it to match binding.
Fixes: ac9aae00f0fc ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c953c764e505428f59ffe6afb1c73b89b5b1ac35 ]
Broadcom ns2 platform has spi-cpol and spi-cpho properties set
incorrectly. As per spi-slave-peripheral-prop.yaml, these properties are
of flag or boolean type and not integer type. Fix the values.
Fixes: d69dbd9f41a7c (arm64: dts: Add ARM PL022 SPI DT nodes for NS2)
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: Ray Jui <rjui@broadcom.com>
CC: Scott Branden <sbranden@broadcom.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 625c24460dbbc3b6c9a148c0a30f0830893fc909 ]
replace millivolt with correct microvolt and adjust value to
the minimal value allowed by documentation.
Found with `make qcom/sdm845-oneplus-fajita.dtb`.
Fixes:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias2-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias3-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias4-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-millivolt', 'qcom,micbias2-millivolt', 'qcom,micbias3-millivolt', 'qcom,micbias4-millivolt' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'
Fixes: 27ca1de07dc3 ("arm64: dts: qcom: sdm845: add slimbus nodes")
Signed-off-by: David Heidelberg <david@ixit.cz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213195105.114596-1-david@ixit.cz
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee017ee353506fcec58e481673e4331ff198a80e ]
The 'fixmap' is a global resource and is used recursively by
create pud mapping(), leading to a potential race condition in the
presence of a concurrent call to alloc_init_pud():
kernel_init thread virtio-mem workqueue thread
================== ===========================
alloc_init_pud(...) alloc_init_pud(...)
pudp = pud_set_fixmap_offset(...) pudp = pud_set_fixmap_offset(...)
READ_ONCE(*pudp)
pud_clear_fixmap(...)
READ_ONCE(*pudp) // CRASH!
As kernel may sleep during creating pud mapping, introduce a mutex lock to
serialise use of the fixmap entries by alloc_init_pud(). However, there is
no need for locking in early boot stage and it doesn't work well with
KASLR enabled when early boot. So, enable lock when system_state doesn't
equal to "SYSTEM_BOOTING".
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: f4710445458c ("arm64: mm: use fixmap when creating page tables")
Link: https://lore.kernel.org/r/20220201114400.56885-1-jianyong.wu@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a32c88ddb9af30e8a16d41d7b9b824c27d29459 upstream.
Commit 6d502b6ba1b2 ("arm64: signal: nofpsimd: Handle fp/simd context for
signal frames") introduced saving the fp/simd context for signal handling
only when support is available. But setup_sigframe_layout() always
reserves memory for fp/simd context. The additional memory is not touched
because preserve_fpsimd_context() is not called and thus the magic is
invalid.
This may lead to an error when parse_user_sigframe() checks the fp/simd
area and does not find a valid magic number.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Fixes: 6d502b6ba1b267b3 ("arm64: signal: nofpsimd: Handle fp/simd context for signal frames")
Cc: <stable@vger.kernel.org> # 5.6.x
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220225104008.820289-1-david.engraf@sysgo.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f34b43e07cb512b28543fdcb9f35d1fbfda9ebc ]
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16fa ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM's infrastructure for spectre mitigations in the vectors in v5.10 and
earlier is different, it uses templates which are used to build a set of
vectors at runtime.
There are two copy-and-paste errors in the templates: __spectre_bhb_loop_k24
should loop 24 times and __spectre_bhb_loop_k32 32.
Fix these.
Reported-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/all/20220310234858.GB16308@amd/
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 268a491aebc25e6dc7c618903b09ac3a2e8af530 ]
The DWC2 USB controller on the Agilex platform does not support clock
gating, so use the chip specific "intel,socfpga-agilex-hsotg"
compatible.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62966cbdda8a92f82d966a45aa671e788b2006f7 ]
There are signal integrity issues running the eMMC at 200MHz on Puma
RK3399-Q7.
Similar to the work-around found for RK3399 Gru boards, lowering the
frequency to 100MHz made the eMMC much more stable, so let's lower the
frequency to 100MHz.
It might be possible to run at 150MHz as on RK3399 Gru boards but only
100MHz was extensively tested.
Cc: Quentin Schulz <foss+kernel@0leil.net>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220119134948.1444965-1-quentin.schulz@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a1cc1697bb56cdf880ad4d17b79a39ef2c294bc9 upstream.
Legacy and old PCI I/O based cards do not support 32-bit I/O addressing.
Since commit 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from
'ranges' DT property") kernel can set different PCIe address on CPU and
different on the bus for the one A37xx address mapping without any firmware
support in case the bus address does not conflict with other A37xx mapping.
So remap I/O space to the bus address 0x0 to enable support for old legacy
I/O port based cards which have hardcoded I/O ports in low address space.
Note that DDR on A37xx is mapped to bus address 0x0. And mapping of I/O
space can be set to address 0x0 too because MEM space and I/O space are
separate and so do not conflict.
Remapping IO space on Turris Mox to different address is not possible to
due bootloader bug.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Cc: stable@vger.kernel.org # 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property")
Cc: stable@vger.kernel.org # 514ef1e62d65 ("arm64: dts: marvell: armada-37xx: Extend PCIe MEM space")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58c9a5060cb7cd529d49c93954cdafe81c1d642a upstream.
The mitigations for Spectre-BHB are only applied when an exception is
taken from user-space. The mitigation status is reported via the spectre_v2
sysfs vulnerabilities file.
When unprivileged eBPF is enabled the mitigation in the exception vectors
can be avoided by an eBPF program.
When unprivileged eBPF is enabled, print a warning and report vulnerable
via the sysfs vulnerabilities file.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 228a26b912287934789023b4132ba76065d9491c upstream.
Future CPUs may implement a clearbhb instruction that is sufficient
to mitigate SpectreBHB. CPUs that implement this instruction, but
not CSV2.3 must be affected by Spectre-BHB.
Add support to use this instruction as the BHB mitigation on CPUs
that support it. The instruction is in the hint space, so it will
be treated by a NOP as older CPUs.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
[ modified for stable: Use a KVM vector template instead of alternatives,
removed bitmap of mitigations ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5905d6af492ee6a4a2205f0d550b3f931b03d03 upstream.
KVM allows the guest to discover whether the ARCH_WORKAROUND SMCCC are
implemented, and to preserve that state during migration through its
firmware register interface.
Add the necessary boiler plate for SMCCC_ARCH_WORKAROUND_3.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558c303c9734af5a813739cd284879227f7297d2 upstream.
Speculation attacks against some high-performance processors can
make use of branch history to influence future speculation.
When taking an exception from user-space, a sequence of branches
or a firmware call overwrites or invalidates the branch history.
The sequence of branches is added to the vectors, and should appear
before the first indirect branch. For systems using KPTI the sequence
is added to the kpti trampoline where it has a free register as the exit
from the trampoline is via a 'ret'. For systems not using KPTI, the same
register tricks are used to free up a register in the vectors.
For the firmware call, arch-workaround-3 clobbers 4 registers, so
there is no choice but to save them to the EL1 stack. This only happens
for entry from EL0, so if we take an exception due to the stack access,
it will not become re-entrant.
For KVM, the existing branch-predictor-hardening vectors are used.
When a spectre version of these vectors is in use, the firmware call
is sufficient to mitigate against Spectre-BHB. For the non-spectre
versions, the sequence of branches is added to the indirect vector.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
[ modified for stable, removed bitmap of mitigations, use kvm template
infrastructure ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bdf3437603d4af87f9c7f424b0c8aeed2420745 upstream.
CPUs vulnerable to Spectre-BHB either need to make an SMC-CC firmware
call from the vectors, or run a sequence of branches. This gets added
to the hyp vectors. If there is no support for arch-workaround-1 in
firmware, the indirect vector will be used.
kvm_init_vector_slots() only initialises the two indirect slots if
the platform is vulnerable to Spectre-v3a. pKVM's hyp_map_vectors()
only initialises __hyp_bp_vect_base if the platform is vulnerable to
Spectre-v3a.
As there are about to more users of the indirect vectors, ensure
their entries in hyp_spectre_vector_selector[] are always initialised,
and __hyp_bp_vect_base defaults to the regular VA mapping.
The Spectre-v3a check is moved to a helper
kvm_system_needs_idmapped_vectors(), and merged with the code
that creates the hyp mappings.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dee435be76f4117410bbd90573a881fd33488f37 upstream.
Speculation attacks against some high-performance processors can
make use of branch history to influence future speculation as part of
a spectre-v2 attack. This is not mitigated by CSV2, meaning CPUs that
previously reported 'Not affected' are now moderately mitigated by CSV2.
Update the value in /sys/devices/system/cpu/vulnerabilities/spectre_v2
to also show the state of the BHB mitigation.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd09128d16fac3c34b80bd6a29088ac632e8ce09 upstream.
The Spectre-BHB workaround adds a firmware call to the vectors. This
is needed on some CPUs, but not others. To avoid the unaffected CPU in
a big/little pair from making the firmware call, create per cpu vectors.
The per-cpu vectors only apply when returning from EL0.
Systems using KPTI can use the canonical 'full-fat' vectors directly at
EL1, the trampoline exit code will switch to this_cpu_vector on exit to
EL0. Systems not using KPTI should always use this_cpu_vector.
this_cpu_vector will point at a vector in tramp_vecs or
__bp_harden_el1_vectors, depending on whether KPTI is in use.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b28a8eebe81c186fdb1a0078263b30576c8e1f42 upstream.
The trampoline code needs to use the address of symbols in the wider
kernel, e.g. vectors. PC-relative addressing wouldn't work as the
trampoline code doesn't run at the address the linker expected.
tramp_ventry uses a literal pool, unless CONFIG_RANDOMIZE_BASE is
set, in which case it uses the data page as a literal pool because
the data page can be unmapped when running in user-space, which is
required for CPUs vulnerable to meltdown.
Pull this logic out as a macro, instead of adding a third copy
of it.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba2689234be92024e5635d30fe744f4853ad97db upstream.
Some CPUs affected by Spectre-BHB need a sequence of branches, or a
firmware call to be run before any indirect branch. This needs to go
in the vectors. No CPU needs both.
While this can be patched in, it would run on all CPUs as there is a
single set of vectors. If only one part of a big/little combination is
affected, the unaffected CPUs have to run the mitigation too.
Create extra vectors that include the sequence. Subsequent patches will
allow affected CPUs to select this set of vectors. Later patches will
modify the loop count to match what the CPU requires.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aff65393fa1401e034656e349abd655cfe272de0 upstream.
kpti is an optional feature, for systems not using kpti a set of
vectors for the spectre-bhb mitigations is needed.
Add another set of vectors, __bp_harden_el1_vectors, that will be
used if a mitigation is needed and kpti is not in use.
The EL1 ventries are repeated verbatim as there is no additional
work needed for entry from EL1.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c406e6462ff14956d690de7bbe5131a5677dc9 upstream.
Adding a second set of vectors to .entry.tramp.text will make it
larger than a single 4K page.
Allow the trampoline text to occupy up to three pages by adding two
more fixmap slots. Previous changes to tramp_valias allowed it to reach
beyond a single page.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c47e4d04ba0f1ea17353d85d45f611277507e07a upstream.
Spectre-BHB needs to add sequences to the vectors. Having one global
set of vectors is a problem for big/little systems where the sequence
is costly on cpus that are not vulnerable.
Making the vectors per-cpu in the style of KVM's bh_harden_hyp_vecs
requires the vectors to be generated by macros.
Make the kpti re-mapping of the kernel optional, so the macros can be
used without kpti.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13d7a08352a83ef2252aeb464a5e08dfc06b5dfd upstream.
The macros for building the kpti trampoline are all behind
CONFIG_UNMAP_KERNEL_AT_EL0, and in a region that outputs to the
.entry.tramp.text section.
Move the macros out so they can be used to generate other kinds of
trampoline. Only the symbols need to be guarded by
CONFIG_UNMAP_KERNEL_AT_EL0 and appear in the .entry.tramp.text section.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed50da7764535f1e24432ded289974f2bf2b0c5a upstream.
The tramp_ventry macro uses tramp_vectors as the address of the vectors
when calculating which ventry in the 'full fat' vectors to branch to.
While there is one set of tramp_vectors, this will be true.
Adding multiple sets of vectors will break this assumption.
Move the generation of the vectors to a macro, and pass the start
of the vectors as an argument to tramp_ventry.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c5bf79b69f911560fbf82214c0971af6e58e682 upstream.
Systems using kpti enter and exit the kernel through a trampoline mapping
that is always mapped, even when the kernel is not. tramp_valias is a macro
to find the address of a symbol in the trampoline mapping.
Adding extra sets of vectors will expand the size of the entry.tramp.text
section to beyond 4K. tramp_valias will be unable to generate addresses
for symbols beyond 4K as it uses the 12 bit immediate of the add
instruction.
As there are now two registers available when tramp_alias is called,
use the extra register to avoid the 4K limit of the 12 bit immediate.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c091fb6ae059cda563b2a4d93fdbc548ef34e1d6 upstream.
The trampoline code has a data page that holds the address of the vectors,
which is unmapped when running in user-space. This ensures that with
CONFIG_RANDOMIZE_BASE, the randomised address of the kernel can't be
discovered until after the kernel has been mapped.
If the trampoline text page is extended to include multiple sets of
vectors, it will be larger than a single page, making it tricky to
find the data page without knowing the size of the trampoline text
pages, which will vary with PAGE_SIZE.
Move the data page to appear before the text page. This allows the
data page to be found without knowing the size of the trampoline text
pages. 'tramp_vectors' is used to refer to the beginning of the
.entry.tramp.text section, do that explicitly.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03aff3a77a58b5b52a77e00537a42090ad57b80b upstream.
Kpti stashes x30 in far_el1 while it uses x30 for all its work.
Making the vectors a per-cpu data structure will require a second
register.
Allow tramp_exit two registers before it unmaps the kernel, by
leaving x30 on the stack, and stashing x29 in far_el1.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d739da1694a0eaef0358a42b76904b611539b77b upstream.
Subsequent patches will add additional sets of vectors that use
the same tricks as the kpti vectors to reach the full-fat vectors.
The full-fat vectors contain some cleanup for kpti that is patched
in by alternatives when kpti is in use. Once there are additional
vectors, the cleanup will be needed in more cases.
But on big/little systems, the cleanup would be harmful if no
trampoline vector were in use. Instead of forcing CPUs that don't
need a trampoline vector to use one, make the trampoline cleanup
optional.
Entry at the top of the vectors will skip the cleanup. The trampoline
vectors can then skip the first instruction, triggering the cleanup
to run.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b33d4860deaecf1d8eec3061b7e7ed7ab0bae8d upstream.
The spectre-v4 sequence includes an SMC from the assembly entry code.
spectre_v4_patch_fw_mitigation_conduit is the patching callback that
generates an HVC or SMC depending on the SMCCC conduit type.
As this isn't specific to spectre-v4, rename it
smccc_patch_fw_mitigation_conduit so it can be re-used.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4330e2c5c04c27bebf89d34e0bc14e6943413067 upstream.
Subsequent patches add even more code to the ventry slots.
Ensure kernels that overflow a ventry slot don't get built.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1175011a7d0030d49dc9c10bde36f08f26d0a8ee upstream.
Add a new HWCAP to detect the Increased precision of Reciprocal Estimate
and Reciprocal Square Root Estimate feature (FEAT_RPRES), introduced in Armv8.7.
Also expose this to userspace in the ID_AA64ISAR2_EL1 feature register.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211210165432.8106-4-joey.gouly@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
