IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 1833b6f46d7e2830251a063935ab464256defe22 upstream.
If the tool on the other side (e.g. wmediumd) gets confused
about the rate, we hit a warning in mac80211. Silence that
by effectively duplicating the check here and dropping the
frame silently (in mac80211 it's dropped with the warning).
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65e5d27df61283e5390f04b09dc79cd832f95607 ]
If aq_nic_stop() fails, aq_ndev_close() returns err without calling
aq_nic_deinit() to release the relevant memory and resource, which
will lead to a memory leak.
We can fix it by deleting the if condition judgment and goto statement to
call aq_nic_deinit() directly after aq_nic_stop() to fix the memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49725ffc15fc4e9fae68c55b691fd25168cbe5c1 ]
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6ff78 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6ff78 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c635ebe8d911a93bd849a9419b01a58783de76f1 ]
The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the
'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the
'uld_mutex' before returning. Additionally, since commit 5148e5950c67
("cxgb4: add EOTID tracking and software context dump"), the access to
these ETHOFLD hardware queues should be protected by the 'mqprio_mutex'
instead.
Fixes: 2d0cb84dd973 ("cxgb4: add ETHOFLD hardware queue support")
Fixes: 5148e5950c67 ("cxgb4: add EOTID tracking and software context dump")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a43206156263fbaf1f2b7f96257441f331e91bb7 ]
Currently usbnet_disconnect() unanchors and frees all deferred URBs
using usb_scuttle_anchored_urbs(), which does not free urb->context,
causing a memory leak as reported by syzbot.
Use a usb_get_from_anchor() while loop instead, similar to what we did
in commit 19cfe912c37b ("Bluetooth: btusb: Fix memory leak in
play_deferred"). Also free urb->sg.
Reported-and-tested-by: syzbot+dcd3e13cf4472f2e0ba1@syzkaller.appspotmail.com
Fixes: 69ee472f2706 ("usbnet & cdc-ether: Autosuspend for online devices")
Fixes: 638c5115a794 ("USBNET: support DMA SG")
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Link: https://lore.kernel.org/r/20220923042551.2745-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 42bc4fafe359ed6b73602b7a2dba0dd99588f8ce upstream.
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 878e2405710aacfeeb19364c300f38b7a9abfe8f ]
There is a separate receive path for small packets (under 256 bytes).
Instead of allocating a new dma-capable skb to be used for the next packet,
this path allocates a skb and copies the data into it (reusing the existing
sbk for the next packet). There are two bytes of junk data at the beginning
of every packet. I believe these are inserted in order to allow aligned DMA
and IP headers. We skip over them using skb_reserve. Before copying over
the data, we must use a barrier to ensure we see the whole packet. The
current code only synchronizes len bytes, starting from the beginning of
the packet, including the junk bytes. However, this leaves off the final
two bytes in the packet. Synchronize the whole packet.
To reproduce this problem, ping a HME with a payload size between 17 and
214
$ ping -s 17 <hme_address>
which will complain rather loudly about the data mismatch. Small packets
(below 60 bytes on the wire) do not have this issue. I suspect this is
related to the padding added to increase the minimum packet size.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220920235018.1675956-1-seanga2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5440428b3da65408dba0241985acb7a05258b85e ]
The dev->can.state is set to CAN_STATE_ERROR_ACTIVE, after the device
has been started. On busy networks the CAN controller might receive
CAN frame between and go into an error state before the dev->can.state
is assigned.
Assign dev->can.state before starting the controller to close the race
window.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220920195216.232481-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed38e64d9b99d65a36c0dbadc3d3f8ddd9ea030 ]
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC
flag; only PFs should. Moreover, TSN-specific code should go to
enetc_qos.c, which should not be included in the VF driver.
Fixes: 79e499829f3f ("net: enetc: add hw tc hw offload features for PSPF capability")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26c013108c12b94bc023bf19198a4300596c98b1 ]
Doing a variable-sized memcpy is slower, and the compiler isn't smart
enough to turn this into a constant-size assignment.
Further, Kees' latest fortified memcpy will actually bark, because the
destination pointer is type sockaddr, not explicitly sockaddr_in or
sockaddr_in6, so it thinks there's an overflow:
memcpy: detected field-spanning write (size 28) of single field
"&endpoint.addr" at drivers/net/wireguard/netlink.c:446 (size 16)
Fix this by just assigning by using explicit casts for each checked
case.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reported-by: syzbot+a448cda4dba2dac50de5@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 684dec3cf45da2b0848298efae4adf3b2aeafeda ]
A previous commit tried to make the ratelimiter timings test more
reliable but in the process made it less reliable on other
configurations. This is an impossible problem to solve without
increasingly ridiculous heuristics. And it's not even a problem that
actually needs to be solved in any comprehensive way, since this is only
ever used during development. So just cordon this off with a DEBUG_
ifdef, just like we do for the trie's randomized tests, so it can be
enabled while hacking on the code, and otherwise disabled in CI. In the
process we also revert 151c8e499f47.
Fixes: 151c8e499f47 ("wireguard: ratelimiter: use hrtimer in selftest")
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf412ec333250cb82bafe57169204e14a9f1c2ac ]
IPA can route packets between IPA-connected entities. The AP and
modem are currently the only such entities supported, and no routing
is required to transfer packets between them.
The number of entries in each routing table is fixed, and defined at
initialization time. Some of these entries are designated for use
by the modem, and the rest are available for the AP to use. The AP
sends a QMI message to the modem which describes (among other
things) information about routing table memory available for the
modem to use.
Currently the QMI initialization packet gives wrong information in
its description of routing tables. What *should* be supplied is the
maximum index that the modem can use for the routing table memory
located at a given location. The current code instead supplies the
total *number* of routing table entries. Furthermore, the modem is
granted the entire table, not just the subset it's supposed to use.
This patch fixes this. First, the ipa_mem_bounds structure is
generalized so its "end" field can be interpreted either as a final
byte offset, or a final array index. Second, the IPv4 and IPv6
(non-hashed and hashed) table information fields in the QMI
ipa_init_modem_driver_req structure are changed to be ipa_mem_bounds
rather than ipa_mem_array structures. Third, we set the "end" value
for each routing table to be the last index, rather than setting the
"count" to be the number of indices. Finally, instead of allowing
the modem to use all of a routing table's memory, it is limited to
just the portion meant to be used by the modem. In all versions of
IPA currently supported, that is IPA_ROUTE_MODEM_COUNT (8) entries.
Update a few comments for clarity.
Fixes: 530f9216a9537 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220913204602.1803004-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ea29143ebe6c453f5fddc80ffe4ed046f44aa3a ]
Entries in an IPA route or filter table are 64-bit little-endian
addresses, each of which refers to a routing or filtering rule.
The format of these table slots are fixed, but IPA_TABLE_ENTRY_SIZE
is used to define their size. This symbol doesn't really add value,
and I think it unnecessarily obscures what a table entry *is*.
So get rid of IPA_TABLE_ENTRY_SIZE, and just use sizeof(__le64) in
its place throughout the code.
Update the comments in "ipa_table.c" to provide a little better
explanation of these table slots.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19aaf72c0c7a26ab7ffc655a6d84da6a379f899b ]
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437c78f976f5b39fc4b2a1c65903a229f55912dd ]
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d4e96b44cf20330c970c3e30ea0a8c3a23feca ]
We currently have a build-time check to ensure that the minimum DMA
allocation alignment satisfies the constraint that IPA filter and
route tables must point to rules that are 128-byte aligned.
But what's really important is that the actual allocated DMA memory
has that alignment, even if the minimum is smaller than that.
Remove the BUILD_BUG_ON() call checking against minimim DMA alignment
and instead verify at rutime that the allocated memory is properly
aligned.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2fd2311de909a7f4e99b4bd11a19e6b671d6a6b ]
Some build time checks in ipa_table_validate_build() assume that a
DMA address is 64 bits wide. That is more restrictive than it has
to be. A route or filter table is 64 bits wide no matter what the
size of a DMA address is on the AP. The code actually uses a
pointer to __le64 to access table entries, and a fixed constant
IPA_TABLE_ENTRY_SIZE to describe the size of those entries.
Loosen up two checks so they still verify some requirements, but
such that they do not assume the size of a DMA address is 64 bits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c48709e6d9d353acaaac1d8e33474756b121d78 ]
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 66bdede495c7 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Co-developed-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a242eb2913a4aa3d6fbdb86559f27628e9466f3 ]
Trying to get the channel from the tx_queue variable here is wrong
because we can only be here if tx_queue is NULL, so we shouldn't
dereference it. As the above comment in the code says, this is very
unlikely to happen, but it's wrong anyway so let's fix it.
I hit this issue because of a different bug that caused tx_queue to be
NULL. If that happens, this is the error message that we get here:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
Fixes: 12804793b17c ("sfc: decouple TXQ type from label")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220914111135.21038-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f232af4295653afa4ade3230462b3be15ad16419 ]
In legacy interrupt mode the tx_channel_offset was hardcoded to 1, but
that's not correct if efx_sepparate_tx_channels is false. In that case,
the offset is 0 because the tx queues are in the single existing channel
at index 0, together with the rx queue.
Without this fix, as soon as you try to send any traffic, it tries to
get the tx queues from an uninitialized channel getting these errors:
WARNING: CPU: 1 PID: 0 at drivers/net/ethernet/sfc/tx.c:540 efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
RIP: 0010:efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
Fixes: c308dfd1b43e ("sfc: fix wrong tx channel offset with efx_separate_tx_channels")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220914103648.16902-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 198eb7e1b81d8ba676d0f4f120c092032ae69a8e ]
While converting max_tx_rate from bytes to Mbps, this value was set to 0,
if the original value was lower than 125000 bytes (1 Mbps). This would
cause no transmission rate limiting to occur. This happened due to lack of
check of max_tx_rate against the 1 Mbps value for max_tx_rate and the
following division by 125000. Fix this issue by adding a helper
i40e_bw_bytes_to_mbits() which sets max_tx_rate to minimum usable value of
50 Mbps, if its value is less than 1 Mbps, otherwise do the required
conversion by dividing by 125000.
Fixes: 5ecae4120a6b ("i40e: Refactor VF BW rate limiting")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372539def2824c43b6afe2403045b140f65c5acc ]
Max MTU sent to VF is set to 0 during memory allocation. It cause
that max MTU on VF is changed to IAVF_MAX_RXBUFFER and does not
depend on data from HW.
Set max_mtu field in virtchnl_vf_resource struct to inform
VF in GET_VF_RESOURCES msg what size should be max frame.
Fixes: dab86afdbbd1 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 399c98c4dc50b7eb7e9f24da7ffdda6f025676ef ]
After setting port VLAN and MTU to 9000 on VF with ice driver there
was an iavf error
"PF returned error -5 (IAVF_ERR_PARAM) to our request 6".
During queue configuration, VF's max packet size was set to
IAVF_MAX_RXBUFFER but on ice max frame size was smaller by VLAN_HLEN
due to making some space for port VLAN as VF is not aware whether it's
in a port VLAN. This mismatch in sizes caused ice to reject queue
configuration with ERR_PARAM error. Proper max_mtu is sent from ice PF
to VF with GET_VF_RESOURCES msg but VF does not look at this.
In iavf change max_frame from IAVF_MAX_RXBUFFER to max_mtu
received from pf with GET_VF_RESOURCES msg to make vf's
max_frame_size dependent from pf. Add check if received max_mtu is
not in eligible range then set it to IAVF_MAX_RXBUFFER.
Fixes: dab86afdbbd1 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66039eb9015eee4f7ff0c99b83c65c7ecb3c8190 ]
Fix bad page state, free inappropriate page in handling dummy
descriptor. iavf_build_skb now has to check not only if rx_buffer is
NULL but also if size is zero, same thing in iavf_clean_rx_irq.
Without this patch driver would free page that will be used
by napi_build_skb.
Fixes: a9f49e006030 ("iavf: Fix handling of dummy receive descriptors")
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd60234222b2fd5573526da7bcd422801f271f5f ]
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The team driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former team
ports after a team device has been deleted; see test_LAG_cleanup() in the
last patch in this series.
Add unsync calls at their expected location, team_close().
v3:
* When adding or deleting a port, only sync/unsync addresses if the team
device is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86247aba599e5b07d7e828e6edaaebb0ef2b1158 ]
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The bonding driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former bond
slaves after a bond has been deleted; see test_LAG_cleanup() in the last
patch in this series.
Add unsync calls, via bond_hw_addr_flush(), at their expected location,
bond_close().
Add dev_mc_add() call to bond_open() to match the above change.
v3:
* When adding or deleting a slave, only sync/unsync, add/del addresses if
the bond is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d9a143ee3408349700f44a9197b7ae0e4faae5d ]
There are already a few definitions of arrays containing
MULTICAST_LACPDU_ADDR and the next patch will add one more use. These all
contain the same constant data so define one common instance for all
bonding code.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 86247aba599e ("net: bonding: Unsync device addresses on ndo_stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca2dccdeeb49a7e408112d681bf447984c845292 ]
The Aquantia datasheet notes that after issuing a Processor-Intensive
MDIO operation, like changing the low-power state of the device, the
driver should wait for the operation to finish before issuing a new MDIO
command.
The new aqr107_wait_processor_intensive_op() function is added which can
be used after these kind of MDIO operations. At the moment, we are only
adding it at the end of the suspend/resume calls.
The issue was identified on a board featuring the AQR113C PHY, on
which commands like 'ip link (..) up / down' issued without any delays
between them would render the link on the PHY to remain down.
The issue was easy to reproduce with a one-liner:
$ ip link set dev ethX down; ip link set dev ethX up; \
ip link set dev ethX down; ip link set dev ethX up;
Fixes: ac9e81c230eb ("net: phy: aquantia: add suspend / resume callbacks for AQR107 family")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220906130451.1483448-1-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81225b2ea161af48e093f58e8dfee6d705b16af4 ]
If an AF_PACKET socket is used to send packets through ipvlan and the
default xmit function of the AF_PACKET socket is changed from
dev_queue_xmit() to packet_direct_xmit() via setsockopt() with the option
name of PACKET_QDISC_BYPASS, the skb->mac_header may not be reset and
remains as the initial value of 65535, this may trigger slab-out-of-bounds
bugs as following:
=================================================================
UG: KASAN: slab-out-of-bounds in ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
PU: 2 PID: 1768 Comm: raw_send Kdump: loaded Not tainted 6.0.0-rc4+ #6
ardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33
all Trace:
print_address_description.constprop.0+0x1d/0x160
print_report.cold+0x4f/0x112
kasan_report+0xa3/0x130
ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
ipvlan_start_xmit+0x29/0xa0 [ipvlan]
__dev_direct_xmit+0x2e2/0x380
packet_direct_xmit+0x22/0x60
packet_snd+0x7c9/0xc40
sock_sendmsg+0x9a/0xa0
__sys_sendto+0x18a/0x230
__x64_sys_sendto+0x74/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause is:
1. packet_snd() only reset skb->mac_header when sock->type is SOCK_RAW
and skb->protocol is not specified as in packet_parse_headers()
2. packet_direct_xmit() doesn't reset skb->mac_header as dev_queue_xmit()
In this case, skb->mac_header is 65535 when ipvlan_xmit_mode_l2() is
called. So when ipvlan_xmit_mode_l2() gets mac header with eth_hdr() which
use "skb->head + skb->mac_header", out-of-bound access occurs.
This patch replaces eth_hdr() with skb_eth_hdr() in ipvlan_xmit_mode_l2()
and reset mac header in multicast to solve this out-of-bound bug.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 809f23c0423a43266e47a7dc67e95b5cb4d1cbfc ]
The underlying hardware may or may not allow reading of the head or tail
registers and it really makes no difference if we use the software
cached values. So, always used the software cached values.
Fixes: 9c6c12595b73 ("i40e: Detection and recovery of TX queue hung logic moved to service_task from tx_timeout")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a09721dd47c8468b3f2fdd73f40422699ffe26dd upstream.
The following happened on an i.MX25 using flexcan with many packets on
the bus:
The rx-offload queue reached a length more than skb_queue_len_max. In
can_rx_offload_offload_one() the drop variable was set to true which
made the call to .mailbox_read() (here: flexcan_mailbox_read()) to
_always_ return ERR_PTR(-ENOBUFS) and drop the rx'ed CAN frame. So
can_rx_offload_offload_one() returned ERR_PTR(-ENOBUFS), too.
can_rx_offload_irq_offload_fifo() looks as follows:
| while (1) {
| skb = can_rx_offload_offload_one(offload, 0);
| if (IS_ERR(skb))
| continue;
| if (!skb)
| break;
| ...
| }
The flexcan driver wrongly always returns ERR_PTR(-ENOBUFS) if drop is
requested, even if there is no CAN frame pending. As the i.MX25 is a
single core CPU, while the rx-offload processing is active, there is
no thread to process packets from the offload queue. So the queue
doesn't get any shorter and this results is a tight loop.
Instead of always returning ERR_PTR(-ENOBUFS) if drop is requested,
return NULL if no CAN frame is pending.
Changes since v1: https://lore.kernel.org/all/20220810144536.389237-1-u.kleine-koenig@pengutronix.de
- don't break in can_rx_offload_irq_offload_fifo() in case of an error,
return NULL in flexcan_mailbox_read() in case of no pending CAN frame
instead
Fixes: 4e9c9484b085 ("can: rx-offload: Prepare for CAN FD support")
Link: https://lore.kernel.org/all/20220811094254.1864367-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org # v5.5
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Thorsten Scherer <t.scherer@eckelmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3a510e2b53785df31d882a773c4c0780b4c825f upstream.
The code was accidentally shifting register values down by tid % 32 instead of
(tid * field_size) % 32.
Cc: stable@vger.kernel.org
Fixes: a28bef561a5c ("mt76: mt7615: re-enable offloading of sequence number assignment")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220826182329.18155-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c0427842aaef161a38ac83b7e8d8fe050b4be04 ]
An invalid packet with a length shorter than the specified length in the
netlink header can lead to use-after-frees and slab-out-of-bounds in the
processing of the netlink attributes, such as the following:
BUG: KASAN: slab-out-of-bounds in __nla_validate_parse+0x1258/0x2010
Read of size 2 at addr ffff88800ac7952c by task kworker/0:1/12
Workqueue: events hwsim_virtio_rx_work
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x5d
print_report.cold+0x5e/0x5e5
kasan_report+0xb1/0x1c0
__nla_validate_parse+0x1258/0x2010
__nla_parse+0x22/0x30
hwsim_virtio_handle_cmd.isra.0+0x13f/0x2d0
hwsim_virtio_rx_work+0x1b2/0x370
process_one_work+0x8df/0x1530
worker_thread+0x575/0x11a0
kthread+0x29d/0x340
ret_from_fork+0x22/0x30
</TASK>
Discarding packets with an invalid length solves this.
Therefore, skb->len must be set at reception.
Change-Id: Ieaeb9a4c62d3beede274881a7c2722c6c6f477b6
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04ec4e6250e5f58b525b08f3dca45c7d7427620e ]
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f7f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffd7bdddaab193c38416fd5dd416d065517d266e ]
The rc code is 0 at the error path "status & CC2520_STATUS_TX_UNDERFLOW".
Assign rc code with '-EINVAL' at this error path to fix it.
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Link: https://lore.kernel.org/r/20220829071259.18330-1-liqiong@nfschina.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55f34b6aec2a8cb47eadaffea773e83bf85de91 ]
Removing 'hotplug-status' in backend_disconnected() means that it will be
removed even in the case that the frontend unilaterally disconnects (which
it is free to do at any time). The consequence of this is that, when the
frontend attempts to re-connect, the backend gets stuck in 'InitWait'
rather than moving straight to 'Connected' (which it can do because the
hotplug script has already run).
Instead, the 'hotplug-status' mode should be removed in netback_remove()
i.e. when the vif really is going away.
Fixes: 0f4558ae9187 ("Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59ac325557b6c14f1f793b90d3946bc145ffa085 ]
pf->avail_txqs was allocated using bitmap_zalloc, bitmap_free should be
used to free this memory.
Fixes: 78b5713ac1241 ("ice: Alloc queue management bitmaps and arrays dynamically")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d0ef7241553f3553a0a2764c69b07892705924c upstream.
This reverts commit a8eb8e6f7159c7c20c0ddac428bde3d110890aa7 as
it can cause invalid link quality command sent to the firmware
and address the off-by-one issue by fixing condition of while loop.
Cc: stable@vger.kernel.org
Fixes: a8eb8e6f7159 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()")
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220815073737.GA999388@wp.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 278d3ba61563ceed3cb248383ced19e14ec7bc1f upstream.
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0955bf957be4bead01fae1d791476260da7325d ]
The function neigh_timer_handler() is a timer handler that runs in an
atomic context. When used by rocker, neigh_timer_handler() calls
"kzalloc(.., GFP_KERNEL)" that may sleep. As a result, the sleep in
atomic context bug will happen. One of the processes is shown below:
ofdpa_fib4_add()
...
neigh_add_timer()
(wait a timer)
neigh_timer_handler()
neigh_release()
neigh_destroy()
rocker_port_neigh_destroy()
rocker_world_port_neigh_destroy()
ofdpa_port_neigh_destroy()
ofdpa_port_ipv4_neigh()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: 00fc0c51e35b ("rocker: Change world_ops API and implementation to be switchdev independant")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe7116f6d3b888778ed6d95e3cf724767b9aedf ]
There is a possible race condition (use-after-free) like below
(FREE) | (USE)
adf7242_remove | adf7242_channel
cancel_delayed_work_sync |
destroy_workqueue (1) | adf7242_cmd_rx
| mod_delayed_work (2)
|
The root cause for this race is that the upper layer (ieee802154) is
unaware of this detaching event and the function adf7242_channel can
be called without any checks.
To fix this, we can add a flag write at the beginning of adf7242_remove
and add flag check in adf7242_channel. Or we can just defer the
destructive operation like other commit 3e0588c291d6 ("hamradio: defer
ax25 kfree after unregister_netdev") which let the
ieee802154_unregister_hw() to handle the synchronization. This patch
takes the second option.
Fixes: 58e9683d1475 ("net: ieee802154: adf7242: Fix OCL calibration
runs")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220808034224.12642-1-linma@zju.edu.cn
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fc4dd452d6c14828eed6369155c75c0ac15bab3 ]
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25d7a5f5a6bb15a2dae0a3f39ea5dda215024726 ]
The ixgbe_ptp_start_cyclecounter is intended to be called whenever the
cyclecounter parameters need to be changed.
Since commit a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x
devices"), this function has cleared the SYSTIME registers and reset the
TSAUXC DISABLE_SYSTIME bit.
While these need to be cleared during ixgbe_ptp_reset, it is wrong to clear
them during ixgbe_ptp_start_cyclecounter. This function may be called
during both reset and link status change. When link changes, the SYSTIME
counter is still operating normally, but the cyclecounter should be updated
to account for the possibly changed parameters.
Clearing SYSTIME when link changes causes the timecounter to jump because
the cycle counter now reads zero.
Extract the SYSTIME initialization out to a new function and call this
during ixgbe_ptp_reset. This prevents the timecounter adjustment and avoids
an unnecessary reset of the current time.
This also restores the original SYSTIME clearing that occurred during
ixgbe_ptp_reset before the commit above.
Reported-by: Steve Payne <spayne@aurora.tech>
Reported-by: Ilya Evenbach <ievenbach@aurora.tech>
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09a89cc59ad67794a11e1d3dd13c5b3172adcc51 ]
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: b16b68918674 ("bnxt_en: Add SR-IOV support for 57500 chips.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b2e3a17e9f279325712b79fb01d1493f9e3e005 ]
Looks to have been left out in an oversight.
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Sainath Grandhi <sainath.grandhi@intel.com>
Fixes: 235a9d89da97 ('ipvtap: IP-VLAN based tap driver')
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821130808.12143-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d745b5062ad2b5da90a5e728d7ca884fc07315fd ]
This is caused by the global variable ad_ticks_per_sec being zero as
demonstrated by the reproducer script discussed below. This causes
all timer values in __ad_timer_to_ticks to be zero, resulting
in the periodic timer to never fire.
To reproduce:
Run the script in
`tools/testing/selftests/drivers/net/bonding/bond-break-lacpdu-tx.sh` which
puts bonding into a state where it never transmits LACPDUs.
line 44: ip link add fbond type bond mode 4 miimon 200 \
xmit_hash_policy 1 ad_actor_sys_prio 65535 lacp_rate fast
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 48: ip link set fbond address 52:54:00:3B:7C:A6
setting bond MAC addr
call stack:
bond->dev->dev_addr = new_mac
line 52: ip link set fbond type bond ad_actor_sys_prio 65535
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 60: ip link set veth1-bond down master fbond
given:
params.ad_actor_system = 0
params.mode = BOND_MODE_8023AD
ad.system.sys_mac_addr == bond->dev->dev_addr
call stack:
bond_enslave
-> bond_3ad_initialize(); because first slave
-> if ad.system.sys_mac_addr != bond->dev->dev_addr
return
results:
Nothing is run in bond_3ad_initialize() because dev_addr equals
sys_mac_addr leaving the global ad_ticks_per_sec zero as it is
never initialized anywhere else.
The if check around the contents of bond_3ad_initialize() is no longer
needed due to commit 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings
changes immediately") which sets ad.system.sys_mac_addr if any one of
the bonding parameters whos set function calls
bond_3ad_update_ad_actor_settings(). This is because if
ad.system.sys_mac_addr is zero it will be set to the current bond mac
address, this causes the if check to never be true.
Fixes: 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings changes immediately")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
