IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 6c75dc94f2b27fff57b305af9236eea181a00b6c ]
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Fixes: 9dd441e4ed57 ("soc: qcom: ipa: GSI transactions")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf412ec333250cb82bafe57169204e14a9f1c2ac ]
IPA can route packets between IPA-connected entities. The AP and
modem are currently the only such entities supported, and no routing
is required to transfer packets between them.
The number of entries in each routing table is fixed, and defined at
initialization time. Some of these entries are designated for use
by the modem, and the rest are available for the AP to use. The AP
sends a QMI message to the modem which describes (among other
things) information about routing table memory available for the
modem to use.
Currently the QMI initialization packet gives wrong information in
its description of routing tables. What *should* be supplied is the
maximum index that the modem can use for the routing table memory
located at a given location. The current code instead supplies the
total *number* of routing table entries. Furthermore, the modem is
granted the entire table, not just the subset it's supposed to use.
This patch fixes this. First, the ipa_mem_bounds structure is
generalized so its "end" field can be interpreted either as a final
byte offset, or a final array index. Second, the IPv4 and IPv6
(non-hashed and hashed) table information fields in the QMI
ipa_init_modem_driver_req structure are changed to be ipa_mem_bounds
rather than ipa_mem_array structures. Third, we set the "end" value
for each routing table to be the last index, rather than setting the
"count" to be the number of indices. Finally, instead of allowing
the modem to use all of a routing table's memory, it is limited to
just the portion meant to be used by the modem. In all versions of
IPA currently supported, that is IPA_ROUTE_MODEM_COUNT (8) entries.
Update a few comments for clarity.
Fixes: 530f9216a9537 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220913204602.1803004-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ea29143ebe6c453f5fddc80ffe4ed046f44aa3a ]
Entries in an IPA route or filter table are 64-bit little-endian
addresses, each of which refers to a routing or filtering rule.
The format of these table slots are fixed, but IPA_TABLE_ENTRY_SIZE
is used to define their size. This symbol doesn't really add value,
and I think it unnecessarily obscures what a table entry *is*.
So get rid of IPA_TABLE_ENTRY_SIZE, and just use sizeof(__le64) in
its place throughout the code.
Update the comments in "ipa_table.c" to provide a little better
explanation of these table slots.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19aaf72c0c7a26ab7ffc655a6d84da6a379f899b ]
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437c78f976f5b39fc4b2a1c65903a229f55912dd ]
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d4e96b44cf20330c970c3e30ea0a8c3a23feca ]
We currently have a build-time check to ensure that the minimum DMA
allocation alignment satisfies the constraint that IPA filter and
route tables must point to rules that are 128-byte aligned.
But what's really important is that the actual allocated DMA memory
has that alignment, even if the minimum is smaller than that.
Remove the BUILD_BUG_ON() call checking against minimim DMA alignment
and instead verify at rutime that the allocated memory is properly
aligned.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2fd2311de909a7f4e99b4bd11a19e6b671d6a6b ]
Some build time checks in ipa_table_validate_build() assume that a
DMA address is 64 bits wide. That is more restrictive than it has
to be. A route or filter table is 64 bits wide no matter what the
size of a DMA address is on the AP. The code actually uses a
pointer to __le64 to access table entries, and a fixed constant
IPA_TABLE_ENTRY_SIZE to describe the size of those entries.
Loosen up two checks so they still verify some requirements, but
such that they do not assume the size of a DMA address is 64 bits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: cf412ec33325 ("net: ipa: properly limit modem routing table use")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8d4380365c515d8e0351f2f46d371738dd19be1 ]
In ipa_smem_init(), a Qualcomm SMEM region is allocated (if needed)
and then its virtual address is fetched using qcom_smem_get(). The
physical address associated with that region is also fetched.
The physical address is adjusted so that it is page-aligned, and an
attempt is made to update the size of the region to compensate for
any non-zero adjustment.
But that adjustment isn't done properly. The physical address is
aligned twice, and as a result the size is never actually adjusted.
Fix this by *not* aligning the "addr" local variable, and instead
making the "phys" local variable be the adjusted "addr" value.
Fixes: a0036bb413d5b ("net: ipa: define SMEM memory region for IPA")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220818134206.567618-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 70132763d5d2e94cd185e3aa92ac6a3ba89068fa upstream.
Currently the (possibly compound) pages used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide
when to free the allocation, you should allocate a compound
page, and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_replenish_one()
to use put_page() instead.
Fixes: 6a606b90153b8 ("net: ipa: allocate transaction in replenish loop")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 155c0c90bca918de6e4327275dfc1d97fd604115 upstream.
Currently the (possibly compound) page used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide when
to free the allocation, you should allocate a compound page,
and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_trans_release()
to use put_page() instead.
Fixes: ed23f02680caa ("net: ipa: define per-endpoint receive buffer size")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5794097b269f15961ed78f7f27b50e51766dec9 upstream.
The aggregation byte limit for an endpoint is currently computed
based on the endpoint's receive buffer size.
However, some bytes at the front of each receive buffer are reserved
on the assumption that--as with SKBs--it might be useful to insert
data (such as headers) before what lands in the buffer.
The aggregation byte limit currently doesn't take into account that
reserved space, and as a result, aggregation could require space
past that which is available in the buffer.
Fix this by reducing the size used to compute the aggregation byte
limit by the NET_SKB_PAD offset reserved for each receive buffer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8290cbe1111105f92f0c8ab455bec8bf98d0630 ]
Each time we are notified that some number of transactions on an RX
channel has completed, we record the number of bytes that have been
transferred since the previous notification. We also track the
number of transactions completed, but that is not currently being
calculated correctly; we're currently counting the number of such
notifications, but each notification can represent many transaction
completions. Fix this.
Fixes: 650d1603825d8 ("soc: qcom: ipa: the generic software interface")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 998c0bd2b3715244da7639cc4e6a2062cb79c3f4 upstream.
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1aaa01dbf4cef95af3e04a5a43986c290e06ea3 upstream.
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c0e3b5ce94947b311348c367db9e11dcb2ccc93 upstream.
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 816316cacad2b5abd5b41423cf04e4845239abd4 ]
The head-of-line blocking timer should only be modified when
head-of-line drop is disabled.
One of the steps in recovering from a modem crash is to enable
dropping of packets with timeout of 0 (immediate). We don't know
how the modem configured its endpoints, so before we program the
timer, we need to ensure HOL_BLOCK is disabled.
Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5c102238cea985d8126b173d06b9e1de88037ee upstream.
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6c2 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b244163f2c45c12053cb0291c955f892e79ed8a9 ]
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. of_node_put() on it before exiting
this function.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 440c3247cba3d9433ac435d371dd7927d68772a7 ]
IPA configuration data includes an array of memory region
descriptors. That was a fixed-size array at one time, but
at some point we started defining it such that it was only
as big as required for a given platform. The actual number
of entries in the array is recorded in the configuration data
along with the array.
A loop in ipa_mem_config() still assumes the array has entries
for all defined memory region IDs. As a result, this loop can
go past the end of the actual array and attempt to write
"canary" values based on nonsensical data.
Fix this, by stashing the number of entries in the array, and
using that rather than IPA_MEM_COUNT in the initialization loop
found in ipa_mem_config().
The only remaining use of IPA_MEM_COUNT is in a validation check
to ensure configuration data doesn't have too many entries.
That's fine for now.
Fixes: 3128aae8c439a ("net: ipa: redefine struct ipa_mem_data")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4afd4b90a7cfe54c7cd9db49e3c36d552325eac ]
We use ipa_cmd_header_valid() to ensure certain values we will
program into hardware are within range, well in advance of when we
actually program them. This way we avoid having to check for errors
when we actually program the hardware.
Unfortunately the dev_err() call for a bad offset value does not
supply the arguments to match the format specifiers properly.
Fix this.
There was also supposed to be a check to ensure the size to be
programmed fits in the field that holds it. Add this missing check.
Rearrange the way we ensure the header table fits in overall IPA
memory range.
Finally, update ipa_cmd_table_valid() so the format of messages
printed for errors matches what's done in ipa_cmd_header_valid().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d65ed76924bc772d3974b0894d870b1aa63b34a ]
In ipa_cmd_register_write_valid() we verify that values we will
supply to a REGISTER_WRITE IPA immediate command will fit in
the fields that need to hold them. This patch fixes some issues
in that function and ipa_cmd_register_write_offset_valid().
The dev_err() call in ipa_cmd_register_write_offset_valid() has
some printf format errors:
- The name of the register (corresponding to the string format
specifier) was not supplied.
- The IPA base offset and offset need to be supplied separately to
match the other format specifiers.
Also make the ~0 constant used there to compute the maximum
supported offset value explicitly unsigned.
There are two other issues in ipa_cmd_register_write_valid():
- There's no need to check the hash flush register for platforms
(like IPA v4.2) that do not support hashed tables
- The highest possible endpoint number, whose status register
offset is computed, is COUNT - 1, not COUNT.
Fix these problems, and add some additional commentary.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bc5015eb9d64cbd14e467db1a56db1472d0d6c ]
We do not support inter-EE channel or event ring commands. Inter-EE
interrupts are disabled (and never re-enabled) for all channels and
event rings, so we have no need for the GSI registers that clear
those interrupt conditions. So remove their definitions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a9ef3e11c5d33e5cb355b4aad1a4caad2407541 ]
When a QMI handle is initialized, an array of message handler
structures is provided, defining how any received message should
be handled based on its type and message ID. The QMI core code
traverses this array when a message arrives and calls the function
associated with the (type, msg_id) found in the array.
The array is supposed to be terminated with an empty (all zero)
entry though. Without it, an unsupported message will cause
the QMI core code to go past the end of the array.
Fix this bug, by properly terminating the message handler arrays
provided when QMI handles are set up by the IPA driver.
Fixes: 530f9216a9537 ("soc: qcom: ipa: AP/modem communications")
Reported-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d23a56b0296d29e7047b41fe0a42a001036160d ]
In gsi_channel_setup(), we check to see if the configuration data
contains any information about channels that are not supported by
the hardware. If one is found, we abort the setup process, but
the error code (ret) is not set in this case. Fix this bug.
Fixes: 650d1603825d8 ("soc: qcom: ipa: the generic software interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210204010655.15619-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ace7a6e287b7e3b33276cd9fe870c326f880480 ]
The "ring->addr = addr;" assignment is done a few lines later so we
can't use "ring->addr" yet. The correct dma_handle is "addr".
Fixes: 650d1603825d ("soc: qcom: ipa: the generic software interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/YBjpTU2oejkNIULT@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afba9dc1f3a5390475006061c0bdc5ad4915878e ]
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <elder@kernel.org>
Fixes: a646d6ec9098 ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106100755.56800-1-stephan@gerhold.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the coherent memory is freed in gsi_trans_pool_exit_dma(), we
are mistakenly passing the size of a single element in the pool
rather than the actual allocated size. Fix this bug.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203215106.17450-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transactions sit on one of several lists, depending on their state
(allocated, pending, complete, or polled). A spinlock protects
against concurrent access when transactions are moved between these
lists.
Transactions are also reference counted. A newly-allocated
transaction has an initial count of 1; a transaction is released in
gsi_trans_free() only if its decremented reference count reaches 0.
Releasing a transaction includes removing it from the polled (or if
unused, allocated) list, so the spinlock is acquired when we release
a transaction.
The reference count is used to allow a caller to synchronously wait
for a committed transaction to complete. In this case, the waiter
takes an extra reference to the transaction *before* committing it
(so it won't be freed), and releases its reference (calls
gsi_trans_free()) when it is done with it.
Similarly, gsi_channel_update() takes an extra reference to ensure a
transaction isn't released before the function is done operating on
it. Until the transaction is moved to the completed list (by this
function) it won't be freed, so this reference is taken "safely."
But in the quiesce path, we want to wait for the "last" transaction,
which we find in the completed or polled list. Transactions on
these lists can be freed at any time, so we (try to) prevent that
by taking the reference while holding the spinlock.
Currently gsi_trans_free() decrements a transaction's reference
count unconditionally, acquiring the lock to remove the transaction
from its list *only* when the count reaches 0. This does not
protect the quiesce path, which depends on the lock to ensure its
extra reference prevents release of the transaction.
Fix this by only dropping the last reference to a transaction
in gsi_trans_free() while holding the spinlock.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201114182017.28270-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA transactions describe actions to be performed by the IPA
hardware. Three cases use IPA transactions: transmitting a socket
buffer; providing a page to receive packet data; and issuing an IPA
immediate command. An IPA transaction contains a scatter/gather
list (SGL) to hold the set of actions to be performed.
We map buffers in the SGL for DMA at the time they are added to the
transaction. For skb TX transactions, we fill the SGL with a call
to skb_to_sgvec(). Page RX transactions involve a single page
pointer, and that is recorded in the SGL with sg_set_page(). In
both of these cases we then map the SGL for DMA with a call to
dma_map_sg().
Immediate commands are different. The payload for an immediate
command comes from a region of coherent DMA memory, which must
*not* be mapped for DMA. For that reason, gsi_trans_cmd_add()
sort of hand-crafts each SGL entry added to a command transaction.
This patch fixes a problem with the code that crafts the SGL entry
for an immediate command. Previously a portion of the SGL entry was
updated using sg_set_buf(). However this is not valid because it
includes a call to virt_to_page() on the buffer, but the command
buffer pointer is not a linear address.
Since we never actually map the SGL for command transactions, there
are very few fields in the SGL we need to fill. Specifically, we
only need to record the DMA address and the length, so they can be
used by __gsi_trans_commit() to fill a TRE. We additionally need to
preserve the SGL flags so for_each_sg() still works. For that we
can simply assign a null page pointer for command SGL entries.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201022010029.11877-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared. It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug. But we also shouldn't suspend or resume any
endpoints that have not been set up.
Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.
Fixes: 84f9bd12d46d ("soc: qcom: ipa: IPA endpoints")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_uc_response_hdlr() a comment uses the wrong function name
when it describes where a clock reference is taken. Fix this.
Also fix the comment in ipa_uc_response_hdlr() to correctly refer to
ipa_uc_setup(), which is where the clock reference described here is
taken.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When "W=2" is supplied to the build command, we get a warning about
shadowing a global declaration (of a typedef) for a variable defined
in ipa_probe(). Rename the variable to get rid of the warning.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two spots where a variable "channel_id" is unnecessarily
redefined inside loops in "gsi.c". This is warned about if
"W=2" is added to the build command.
Note that this problem is harmless, so there's no need to backport
it as a bugfix.
Remove a comment in gsi_init() about waking the system; the GSI
interrupt does not wake the system any more.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI general interrupt is managed by three registers: enable;
status; and clear. The three registers have same set of field bits
at the same locations. Use a common set of field masks for all
three registers to avoid duplication.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI global interrupt is managed by three registers: enable;
status; and clear. The three registers have same set of field bits
at the same locations. Use a common set of field masks for all
three registers to avoid duplication.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI interrupt type register and interrupt type mask register
have the same field bits at the same locations. Use a common set of
field masks for both registers rather than essentially duplicating
them. The only place the interrupt mask register uses any of these
is in gsi_irq_enable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the field masks used for fields in a status structure are
unused. Remove their definitions; we can add them back again when
we actually use them to handle arriving status messages. These are
warned about if "W=2" is added to the build command.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the deaggregation status exception type is ever actually used.
If any other status exception type is reported we basically ignore
it, and consume the packet. Remove the unused definitions of status
exception type symbols; they can be added back when we actually
handle them.
Separately, two consecutive if statements test the same condition
near the top of ipa_endpoint_suspend_one(). Instead, use a single
test with a block that combines the previously-separate lines of
code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three status opcodes are not currently supported. Symbols
representing their numeric values are defined but never used.
Remove those unused definitions; they can be defined again
when they actually get used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "gsi_trans.c", the field mask TRE_FLAGS_IEOB_FMASK is defined but
never used. Although there's no harm in defining this, remove it
for now and redefine it at some future date if it becomes needed.
This is warned about if "W=2" is added to the build command.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now trigger a system resume when we receive an IPA SUSPEND
interrupt. We should *not* wake up on GSI interrupts.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we handle wakeup interrupts properly, arrange for the IPA
interrupt to be treated as a wakeup interrupt.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch causes a system resume to be triggered when a
packet is available for receipt on a suspended RX endpoint.
The CLOCK_HELD flag was previously used to indicate that an extra
clock reference was held, preventing suspend. But we no longer need
such a flag:
- We take an initial reference in ipa_config().
- That reference is held until ipa_suspend() releases it.
- A subsequent system resume leads to a reference getting
re-acquired in ipa_resume().
- This can repeat until ultimately the module is removed, where
ipa_remove() releases the reference.
We no longer need a special flag to determine whether this extra
reference is held--it is, provided probe has completed successfully
and the driver is not suspended (or removed).
On the other hand, once suspended, it's possible for more than one
endpoint to trip the IPA SUSPEND interrupt, and we only want to
trigger the system resume once. So repurpose the Boolean CLOCK_HELD
flag to record whether the IPA SUSPEND handler should initiate a
system resume.
The flag will be be cleared each time ipa_suspend() is called,
*before* any endpoints are suspended. And it will be set inside the
IPA SUSPEND interrupt handler exactly once per suspend.
Rename the flag IPA_FLAG_RESUMED to reflect its new purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to wakeup_source_register() in ipa_probe() does not do what
it was intended to do. Call device_init_wakeup() in ipa_setup()
instead, to set the IPA device as wakeup-capable and to initially
enable wakeup capability.
When we receive a SUSPEND interrupt, call pm_wakeup_dev_event()
with a zero processing time, to simply call for a resume without
any other processing. The ipa_resume() call will take care of
waking things up again, and will handle receiving the packet.
Note that this gets rid of a clock reference counting bug that
occurred when handling an IPA SUSPEND interrupt. Specifically,
ipa_suspend_handler() took an IPA clock reference *in addition*
to the one taken by ipa_resume(). There is no need to back-port
this fix however, because it only affects code that was not
previously working (this patch is part of fixing that).
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when (before) the last IPA clock reference is dropped,
all endpoints are suspended. And whenever the first IPA clock
reference is taken, all endpoints are resumed (or started).
In most cases there's no need to start endpoints when the clock
starts. So move the calls to ipa_endpoint_suspend() and
ipa_endpoint_resume() out of ipa_clock_put() and ipa_clock_get(),
respectiely. Instead, only suspend endpoints when handling a system
suspend, and only resume endpoints when handling a system resume.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We take a clock reference in ipa_config() in order to prevent the
the IPA clock from being shutdown until a power management suspend
request arrives. An atomic field in the IPA structure records
whether that extra reference had been taken.
Rather than using an atomic to represent a Boolean value, define
a new flags bitmap, and define a "clock held" flag to represent
whether the extra clock reference has been taken.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the checking provided by refcount_t, rather than
using a plain atomic to represent the IPA clock reference count.
Note that we need to *set* the value to 1 in ipa_clock_get() rather
than incrementing it from 0 (because doing that is considered an
error for a refcount_t).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like u32p_replace_bits() should be used instead of
u32_replace_bits() which does not modifies the value but returns the
modified version.
Fixes: 2b9feef2b6c2 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
