IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 60413129ee2b38a80347489270af7f6e1c1de4d0 ]
When using the codec through the generic audio graph card, there are at
least two calls of es8316_set_dai_sysclk(), with the effect of limiting
the allowed sample rates according to the MCLK/LRCK ratios supported by
the codec:
1. During audio card setup, to set the initial MCLK - see
asoc_simple_init_dai().
2. Before opening a stream, to update MCLK, according to the stream
sample rate and the multiplication factor - see
asoc_simple_hw_params().
In some cases the initial MCLK might be set to a frequency that doesn't
match any of the supported ratios, e.g. 12287999 instead of 12288000,
which is only 1 Hz below the supported clock, as that is what the
hardware reports. This creates an empty list of rate constraints, which
is further passed to snd_pcm_hw_constraint_list() via
es8316_pcm_startup(), and causes the following error on the very first
access of the sound card:
$ speaker-test -D hw:Analog,0 -F S16_LE -c 2 -t wav
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
Note that all subsequent retries succeed thanks to the updated MCLK set
at point 2 above, which uses a computed frequency value instead of a
reading from the hardware registers. Normally this would have mitigated
the issue, but es8316_pcm_startup() executes before the 2nd call to
es8316_set_dai_sysclk(), hence it cannot make use of the updated
constraints.
Since es8316_pcm_hw_params() performs anyway a final validation of MCLK
against the stream sample rate and the supported MCLK/LRCK ratios, fix
the issue by ensuring that sysclk_constraints list is only set when at
least one supported sample rate is autodetected by the codec.
Fixes: b8b88b70875a ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f073429037cd79d7311cd8236311c53f5ea8f01 ]
The following error occurs when trying to restore a previously saved
ALSA mixer state (tested on a Rock 5B board):
$ alsactl --no-ucm -f /tmp/asound.state store hw:Analog
$ alsactl --no-ucm -I -f /tmp/asound.state restore hw:Analog
alsactl: set_control:1475: Cannot write control '2:0:0:ALC Capture Target Volume:0' : Invalid argument
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
ALCLVL | dB gain
-------+--------
0000 | -16.5
0001 | -15.0
0010 | -13.5
.... | .....
0111 | -6.0
1000 | -4.5
1001 | -3.0
1010 | -1.5
.... | .....
1111 | -1.5
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
Fixes: b8b88b70875a ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e384dba03e3294ce7ea69e4da558e9bf8f0e8946 ]
Add entries for Positivo laptops: CW14Q01P, K1424G, N14ZP74G to the
DMI table, so that active-high jack-detect will work properly on
these laptops.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://lore.kernel.org/r/20230529181911.632851-1-edson.drosdeck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e7a6d4797ef521c0762914610ed682e102b9d36 ]
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
Fixes: a0aab9e1404a ("ASoC: codecs: add wsa881x amplifier support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523154605.4284-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f63550e2b165208a2f382afcaf5551df9569e1d4 ]
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x87 # out, dac
ssmset 0x06 0x07 # chip
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
(enable MCLK)
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
(enable MCLK after reset)
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
NOT OK
ssmset 0x06 0x07 # chip, out, dac
NOT OK
Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39db65a0a17b54915b269d3685f253a4731f344c ]
The driver is able to work fine without relying on a mandatory interrupt
being assigned to the I2C device. This is only needed when making use of
the jack-detect support.
However, the following warning message is always emitted when there is
no such interrupt available:
es8316 0-0011: Failed to get IRQ 0: -22
Do not attempt to request an IRQ if it is not available/valid. This also
ensures the rather misleading message is not displayed anymore.
Also note the IRQ validation relies on commit dab472eb931bc291 ("i2c /
ACPI: Use 0 to indicate that device does not have interrupt assigned").
Fixes: 822257661031 ("ASoC: es8316: Add jack-detect support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230328094901.50763-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cf2aa665901054b140eb71748661ceae99b6b5a ]
Use the new IRQF_NO_AUTOEN flag when requesting the IRQ, rather then
disabling it immediately after requesting it.
This fixes a possible race where the IRQ might trigger between requesting
and disabling it; and this also leads to a small code cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211003132255.31743-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 39db65a0a17b ("ASoC: es8316: Handle optional IRQ assignment")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de2cc3707b6b6e2ad40bd24ce09a5c1f65d01e1 ]
Without gpiolib, this driver fails to link:
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `chip_gpio_get':
zl38060.c:(.text+0x30): undefined reference to `gpiochip_get_data'
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `zl38_spi_probe':
zl38060.c:(.text+0xa18): undefined reference to `devm_gpiochip_add_data_with_key'
This appears to have been in the driver since the start, but is hard to
hit in randconfig testing since gpiolib is almost always selected by something
else.
Fixes: 52e8a94baf90 ("ASoC: Add initial ZL38060 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230227085850.2503725-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e70aaae32b72d3088d18a3447b67112b3f5979a ]
The usage of GPIOs is optional in the code so don't force on gpiolib when
building it, avoiding warnings in randconfigs.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220202192333.3655269-6-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0de2cc3707b6 ("ASoC: zl38060 add gpiolib dependency")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5bfa7277ee7d944421e0ef193586c6e34d7492c ]
The regulators are supposed to be controlled through the
set_bias_level() component callback. Moreover, the regulators are not
enabled during probe and so, this would lead to a regulator unbalanced
use count.
Fixes: ca514c0f12b02 ("ASOC: Add ADAU7118 8 Channel PDM-to-I2S/TDM Converter driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230224104551.1139981-1-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 771725efe5e2e5396dd9d1220437e5f9d6b9ca9d ]
When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.
The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.
This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).
In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.
Fixes: d5214321498a ("ASoC: tlv320adcx140: Add support for configuring GPIO pin")
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e18c6da62edc780e4f4f3c9ce07bdacd69505182 ]
While looking through legacy platform data users, I noticed that
the DT probing never uses data from the DT properties, as the
platform_data structure gets overwritten directly after it
is initialized.
There have never been any boards defining the platform_data in
the mainline kernel either, so this driver so far only worked
with patched kernels or with the default values.
For the benefit of possible downstream users, fix the DT probe
by no longer overwriting the data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230126162203.2986339-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472a6309c6467af89dbf660a8310369cc9cb041f ]
Restore volume after charge pump and PGA activation to ensure
that volume settings are correctly applied when re-enabling codec
from SND_SOC_BIAS_OFF state.
CLASS_W, CHARGE_PUMP and POWER_MANAGEMENT_2 register configuration
affect how the volume register are applied and must be configured first.
Fixes: a91eb199e4dc ("ASoC: Initial WM8904 CODEC driver")
Link: https://lore.kernel.org/all/c7864c35-738c-a867-a6a6-ddf9f98df7e7@gmail.com/
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221223080247.7258-1-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8444560b4d9302a511f0996f4cfdf85b628f4ca upstream.
The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 636110411ca726f19ef8e87b0be51bb9a4cdef06 upstream.
Overloading the tx_mask with a linear value is asking for trouble and
only works because the codec_dai hw_params() is called before the
cpu_dai hw_params().
Move to the more generic set_stream() API to pass the hdac_stream
information.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20211224021034.26635-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c900dcc3f7331a67ed29739d74524e428d137fb ]
For some reason rt5670_i2c_probe() does a pm_runtime_put() at the end
of a successful probe. But it has never done a pm_runtime_get() leading
to the following error being logged into dmesg:
rt5670 i2c-10EC5640:00: Runtime PM usage count underflow!
Fix this by removing the unnecessary pm_runtime_put().
Fixes: 64e89e5f5548 ("ASoC: rt5670: Add runtime PM support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221213123319.11285-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9529dc167ffcdfd201b9f0eda71015f174095f7e ]
Fix this by dropping wm8994->accdet_lock while calling
cancel_delayed_work_sync(&wm8994->mic_work) in wm1811_jackdet_irq().
Fixes: c0cc3f166525 ("ASoC: wm8994: Allow a delay between jack insertion and microphone detect")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221209091657.1183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 953dbd1cef18ce9ac0d69c1bd735b929fe52a17e ]
KBL-R RVP platforms also use combojack, so we need to enable that
configuration for them.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b801be6f8e53676b9f2b105f54e35c745c1b22 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:f086ba9d5389c ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160402.126140-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d1bb6cc1a654c8693a85b1d262e610196edec8b ]
The table in the datasheet actually shows the volume values in the wrong
order, with the two -3dB values being reversed. This appears to have
caused the lower of the two values to be used in the driver when the
higher should have been, correct this mixup.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221125162348.1288005-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca507bf99611c82dafced73e921c1b10ee12869 ]
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb8e9b36b5b7f2e77892981ff6c27ee831d8026 ]
Since commit bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes: bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faac764ea1ea6898d93e46c403271fb105c0906e ]
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59bf547a7dd366f93bfebb7487959580ca6c0ec ]
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df496157a5afa1b6d1f4c46ad6549c2c346d1e59 ]
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75d8b1662ca5c20cf8365575222abaef18ff1f50 ]
The driver missed the default value of register 0xc070/0xc360.
This patch adds that default value to avoid invalid register access
when the device doesn't be enumerated yet.
BugLink: https://github.com/thesofproject/linux/issues/3924
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221019095715.31082-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80852f8268769715db335a22305e81a0c4a38a84 ]
At the moment Capture source selector appears on Playback
tab in the alsamixer and has a senseless name.
Let's fix that.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-5-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1538e2c8c9b7e7a656effcc6e4e7cfe8c1b405fd ]
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-4-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088777bf65b98cfa4b5378119d0a7d49a58ece44 ]
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-3-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1013999b431b4bcdc1f5ae47dd3338122751db31 ]
Line In path stayed powered off during capturing or
bypass to mixer.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-2-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1aa2ae3eaa96e70229fa61deee87ef4528ffdf ]
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Tested-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4ab29b0f3a6f1e167c5a627f7cd036c1d2b7d65 ]
It would be better to keep the pm_runtime enables before the
IRQ and component stuff. Both of those could start triggering
PM runtime events.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221008140522.134912-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ce83e3bb26feba0fcdd59667fde942b3a600a1 ]
This reverts commit 41a736ac20602f64773e80f0f5b32cde1830a44a.
The pm_runtime_disable is redundant when error returns in
wm8997_probe, we just revert the old patch to fix it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010114852.88127-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d4e966f4cd73ff69bf06934e8e14a33fb7ef447 ]
This reverts commit 86b46bf1feb83898d89a2b4a8d08d21e9ea277a7.
The pm_runtime_disable is redundant when error returns in
wm5110_probe, we just revert the old patch to fix it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010114852.88127-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de71d7567e358effd06dfc3e2a154b25f1331c10 ]
This reverts commit fcbb60820cd3008bb44334a0395e5e57ccb77329.
The pm_runtime_disable is redundant when error returns in
wm5102_probe, we just revert the old patch to fix it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010114852.88127-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73f11e895e140537e7f8c7251211ccd3ce0782b ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of mt6660_i2c_probe.
Fixes:f289e55c6eeb4 ("ASoC: Add MediaTek MT6660 Speaker Amp Driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160116.125020-5-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcbb60820cd3008bb44334a0395e5e57ccb77329 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5102_probe.
Fixes:93e8791dd34ca ("ASoC: wm5102: Initial driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160116.125020-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b46bf1feb83898d89a2b4a8d08d21e9ea277a7 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5110_probe.
Fixes:5c6af635fd772 ("ASoC: wm5110: Add audio CODEC driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160116.125020-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41a736ac20602f64773e80f0f5b32cde1830a44a ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm8997_probe
Fixes:40843aea5a9bd ("ASoC: wm8997: Initial CODEC driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160116.125020-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb4e4349afe7eecdb0499582f1c777031e3a7c8 ]
If clk_hw_register() fails, the corresponding clk should not be
unregistered.
To handle errors from loops, clean up partial iterations before doing the
goto. So add a clk_hw_unregister().
Then use a while (--i >= 0) loop in the unwind section.
Fixes: 78013a1cf297 ("ASoC: da7219: Fix clock handling around codec level probe")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/e4acceab57a0d9e477a8d5890a45c5309e553e7c.1663875789.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5ad67f13623548e5aff847f89700c178aaf2a98 ]
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one permanently mutes an
ongoing stream by toggling the associated speaker pin control.
(This mirrors commit 1e5907bcb3a3 ("ASoC: tas2770: Fix handling of
mute/unmute") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09273f38832406db19a8907a934687cc10660a6b ]
The driver is setting the PWR_CTRL field in both the set_bias_level
callback and on DAPM events of the DAC widget (and also in the
mute_stream method). Drop the set_bias_level callback altogether as the
power setting it does is in conflict with the other code paths.
(This mirrors commit c8a6ae3fe1c8 ("ASoC: tas2770: Drop conflicting
set_bias_level power setting") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23204d928a27146d13e11c9383632775345ecca8 ]
The part is a mono speaker amp, but it can do downmix and switch between
left and right channel, so the right channel range is 1 to 2.
(This mirrors commit bf54d97a835d ("ASoC: tas2770: Allow mono streams")
which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e96bca7eaa5747633ec638b065630ff83728982a upstream.
Slimbus streams are first prepared and then enabled, so the cleanup path
should reverse it. The unprepare sets stream->num_ports to 0 and frees
the stream->ports. Calling disable after unprepare was not really
effective (channels was not deactivated) and could lead to further
issues due to making transfers on unprepared stream.
Fixes: a61f3b4f476e ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220921145354.1683791-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea8ef003aa53ad23e7705c5cab1c4e664faa6c79 upstream.
Slimbus streams are first prepared and then enabled, so the cleanup path
should reverse it. The unprepare sets stream->num_ports to 0 and frees
the stream->ports. Calling disable after unprepare was not really
effective (channels was not deactivated) and could lead to further
issues due to making transfers on unprepared stream.
Fixes: 20aedafdf492 ("ASoC: wcd9335: add support to wcd9335 codec")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220921145354.1683791-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a0342ede303fc420f3a388e1ae82da3ae8ff6bd ]
On probe of the ASoC component, the device is reset but the regcache is
retained. This means the regcache gets out of sync if the codec is
rebound to a sound card for a second time. Fix it by reinitializing the
regcache to defaults after the device is reset.
Fixes: b0bcbe615756 ("ASoC: tas2770: Fix calling reset in probe")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220919173453.84292-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5628560e90395d3812800a8e44a01c32ffa429ec ]
The semaphore of nau8824 wasn't properly unlocked at some error
handling code paths, hence this may result in the unbalance (and
potential lock-up). Fix them to handle the semaphore up properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220823081000.2965-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e5907bcb3a3b569be0a03ebe668bba2ed320a50 upstream.
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one can mute an ongoing stream
by toggling a speaker pin control.
Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-5-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
