IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This reverts commit 972acd701b1982da9cdbeb892bf17eeef2094508 which is
commit 72d00e560d10665e6139c9431956a87ded6e9880 upstream.
Marek writes:
The commit message states 'Cc: stable@vger.kernel.org # v5.18+'
and the commit should only be applied to Linux 5.18.y and newer,
on anything older it breaks PLL configuration due to missing
prerequisite patches.
Reported-by: Marek Vasut <marex@denx.de>
Cc: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/4e5fa5b2-66b8-8f0b-ccb9-c2b774054e4e@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72d00e560d10665e6139c9431956a87ded6e9880 upstream.
Since commit b09c68dc57c9 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:
- Check if the target rate is hardcoded in the frequency table
- Check if varying only kdiv is possible, so switch over is glitch free
- Compute rate dynamically by iterating over pdiv range
If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.
For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.
This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267196 0 0 50000 N
audio_pll1_out 1 1 0 393215995 0 0 50000 Y
and afterwards:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267200 0 0 50000 N
audio_pll1_out 1 1 0 393216000 0 0 50000 Y
This change is equivalent to adding following hardcoded values:
/* rate mdiv pdiv sdiv kdiv */
PLL_1443X_RATE(393216000, 655, 5, 3, 23593),
PLL_1443X_RATE(361267200, 497, 33, 0, -16882),
Fixes: 053a4ffe2988 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4dd432d985ef258e3bc436e568fba4b987b59171 ]
Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.
This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:
- sai5 is running normally and divides Audio PLL out by 16.
- Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
- rates for children are recalculated and rates are set recursively
- imx8m_clk_composite_divider_set_rate(sai5) is called with
32/16 = 2Hz more
- imx8m_clk_composite_divider_set_rate computes same divider as before
- divider register is written, so it restarts counting from zero and
MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.
Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.
Fixes: d3ff9728134e ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c30f600f1f41dcf5ef0fb02e9a201f9b2e8f31bd ]
The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.
Fixes: 9c140d992676 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878b02d5f3b56cb090dbe2c70c89273be144087f ]
Replace of_iomap() and kzalloc() with devm_of_iomap() and devm_kzalloc()
which can automatically release the related memory when the device
or driver is removed or unloaded to avoid potential memory leak.
In this case, iounmap(anatop_base) in line 427,433 are removed
as manual release is not required.
Besides, referring to clk-imx8mq.c, check the return code of
of_clk_add_hw_provider, if it returns negtive, print error info
and unregister hws, which makes the program more robust.
Fixes: 9c140d992676 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Yuxing Liu <lyx2022@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230503070607.2462-1-lyx2022@hust.edu.cn
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 188d070de9132667956f5aadd98d2bd87d3eac89 ]
Use devm_of_iomap() instead of of_iomap() to automatically handle
the unused ioremap region.
If any error occurs, regions allocated by kzalloc() will leak,
but using devm_kzalloc() instead will automatically free the memory
using devm_kfree().
Fixes: daeb14545514 ("clk: imx: imx8mn: Switch to clk_hw based API")
Fixes: 96d6392b54db ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Hao Luo <m202171776@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230411015107.2645-1-m202171776@hust.edu.cn
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4419db4086e8c31821da14140e81498516a3c75 ]
In case imx_register_uart_clocks return early, the imx_uart_clocks
memory will be no freed. So execute kfree always to avoid memory leak.
Fixes: 379c9a24cc23 ("clk: imx: Fix reparenting of UARTs not associated with stdout")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230104110032.1220721-2-peng.fan@oss.nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed1f4ccfe947a3e1018a3bd7325134574c7ff9b3 ]
32K usb suspend clock gate is shared with usb_root_clk, this
shared clock gate was initially defined only for usb suspend
clock, usb suspend clk is kept on while system is active or
system sleep with usb wakeup enabled, so usb root clock is
fine with this situation; with the commit cf7f3f4fa9e5
("clk: imx8mp: fix usb_root_clk parent"), this clock gate is
changed to be for usb root clock, but usb root clock will
be off while usb is suspended, so usb suspend clock will be
gated too, this cause some usb functionalities will not work,
so define this clock to be a shared clock gate to conform with
the real HW status.
Fixes: 9c140d9926761 ("clk: imx: Add support for i.MX8MP clock driver")
Cc: stable@vger.kernel.org # v5.19+
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1664549663-20364-2-git-send-email-jun.li@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43896f56b59eeaf08687fa976257ae7083d01b41 ]
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220427162131.3127303-1-l.stach@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Stable-dep-of: 5c1f7f109094 ("dt-bindings: clocks: imx8mp: Add ID for usb suspend clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39772efd98adecbd5b8c6096d465d2fcbafbde6a ]
Add pixel clock for second LCDIFv3 interface. Both LCDIFv3 interfaces use
the same set of parent clock, so deduplicate imx8mp_media_disp1_pix_sels
into common imx8mp_media_disp_pix_sels and use it for both.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220313123949.207284-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Stable-dep-of: 5c1f7f109094 ("dt-bindings: clocks: imx8mp: Add ID for usb suspend clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7fa365ff66f16772dc06b480cd78f858d10856b ]
There is no occurrence of the hdmi oscillator in the reference manual
(document IMX8MNRM Rev 2, 07/2022). Further, if we consider the indexes
76-81 and 134 of the "Clock Root" table of chapter 5 of the RM, there is
no entry for the source select bits 101b, which is the setting referenced
by "osc_hdmi".
Fix by renaming "osc_hdmi" with "dummy", a clock which has already been
used for missing source select bits.
Tested on the BSH SystemMaster (SMM) S2 board.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221117113637.1978703-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1ff1bfe81e763420afd5f3f25f0b3cbfd97055c ]
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com
Tested-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf7f3f4fa9e57b8e9f594823e77e6cbb0ce2b254 upstream.
According to reference mannual CCGR77(usb) sources from hsio_axi, fix
it.
Fixes: 9c140d9926761 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220507125430.793287-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eccac77ede3946c90143447cdc785dc16aec4b24 ]
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. The
CCGR121 belongs to ECSPI2 and it is not shared.
Fixes: 8f6d8094b215b57 ("ARM: imx: add imx7d clk tree support")
Reported-by: David Wolfe <david.wolfe@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220127141052.1900174-2-abel.vesa@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570727e9acfac1c2330a01dd5e1272e9c3acec08 ]
When attempting to use sys_pll1_80m as the parent for clko1, the
system hangs. This is due to the fact that the source select
for sys_pll1_80m was incorrectly pointing to m7_alt_pll_clk, which
doesn't yet exist.
According to Rev 3 of the TRM, The imx8mn_clko1_sels also incorrectly
references an osc_27m which does not exist, nor does an entry for
source select bits 010b. Fix both by inserting a dummy clock into
the missing space in the table and renaming the incorrectly name clock
with dummy.
Fixes: 96d6392b54db ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211117133202.775633-1-aford173@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eee377b8f44e7ac4f76bbf2440e5cbbc1d25c25f upstream.
Replace builtin_platform_driver_probe with module_platform_driver_probe
because CONFIG_CLK_IMX8QXP can be set to =m (kernel module).
Fixes: e0d0d4d86c766 ("clk: imx8qxp: Support building i.MX8QXP clock driver as module")
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20210904235418.2442-1-miles.chen@mediatek.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f9d61869640f732599ec36b984c2b5c46067519 ]
The csi_sel mux register is located in the CCM register base and not the
CCM_ANALOG register base. So move it to the correct position in code.
Otherwise changing the parent of the csi clock can lead to a complete
system failure due to the CCM_ANALOG_PLL_SYS_TOG register being falsely
modified.
Also remove the SET_RATE_PARENT flag since one possible supply for the
csi_sel mux is the system PLL which we don't want to modify.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-1-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36207b848a6490e14664e2197a1c8ab51d8148e ]
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
Since 936c383673b9 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
echo 25000000 > userspace/set_freq
imx8m-ddrc-devfreq 3d400000.memory-controller: failed to set
dram_apb parent: -16
Fix this by adding a new i.MX composite flag for firmware managed
clocks, which clears SET_PARENT_GATE.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Fixes: 936c383673b9 ("clk: imx: fix composite peripheral flags")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210810151432.9228-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 283f1b9a0401859c53fdd6483ab66f1c4fadaea5 ]
The earlycon depends on the bootloader setup UART clocks being retained.
There're actually two uart clocks (ipg, per) on MX6QDL,
but the 'Fixes' commit change to register only one which means
another clock may be disabled during booting phase
and result in the earlycon unwork.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 379c9a24cc23 ("clk: imx: Fix reparenting of UARTs not associated with stdout")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20210702085438.1988087-1-aisheng.dong@nxp.com
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c586f53ae159c6c1390f093a1ec94baef2df9f3a ]
Remove the PLL clock gates as the allowing to gate the sys1_pll_266m breaks
the uSDHC module which is sporadically unable to enumerate devices after
this change. Also it makes AMP clock management harder with no obvious
benefit to Linux, so just revert the change.
Link: https://lore.kernel.org/r/20210528180135.1640876-1-l.stach@pengutronix.de
Fixes: b04383b6a558 ("clk: imx8mq: Define gates for pll1/2 fixed dividers")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 379c9a24cc239000b1dec53db02fe17a86947423 ]
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73f6b7ed9835ad9f953aebd60dd720aabc487b81 upstream.
A previous patch introduced a harmless randconfig warning:
WARNING: unmet direct dependencies detected for MXC_CLK_SCU
Depends on [n]: COMMON_CLK [=y] && ARCH_MXC [=n] && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Selected by [m]:
- CLK_IMX8QXP [=m] && COMMON_CLK [=y] && (ARCH_MXC [=n] && ARM64 [=y] || COMPILE_TEST [=y]) && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Since the symbol is now hidden and only selected by other symbols,
just remove the dependencies and require the other drivers to
get it right.
Fixes: 6247e31b7530 ("clk: imx: scu: fix MXC_CLK_SCU module build break")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201230155244.981757-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue can be reproduced by having a kernel config with
CONFIG_IMX_MBOX=m and CONFIG_MXC_CLK_SCU=m. It's caused by the Makefile
wanting to build clk-scu.o and clk-imx8qxp.o as different targets but
that doesn't work (e.g. MXC_CLK_SCU = y while CLK_IMX8QXP = n)
"obj-$(CONFIG_MXC_CLK_SCU) += clk-imx-scu.o clk-imx-lpcg-scu.o
clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o"
Having MXC_CLK_SCU=y/m while CLK_IMX8QXP=n will cause a linker problem
like below:
LD [M] drivers/clk/imx/clk-imx-scu.o
arm-poky-linux-gnueabi-ld: no input files
Make MXC_CLK_SCU be un-selectable by users so it can only be selected by
the CLK_IMX8QXP option, ensuring the two symbols are built together.
Drop COMPILE_TEST too because this option isn't selectable anymore. We
can remove it from MXC_CLK_SCU because CLK_IMX8QXP selects MXC_CLK_SCU
which already has COMPILE_TEST.
Fixes: e0d0d4d86c766 ("clk: imx8qxp: Support building i.MX8QXP clock driver as module")
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20201130084624.21113-1-aisheng.dong@nxp.com
[sboyd@kernel.org: Rework commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673b9e ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040cd3 ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As i.MX21 support has been removed, get rid of its clock driver too.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx35_clocks_init() has been used to register clocks on i.MX35
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx35_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx31_clocks_init() has been used to register clocks on i.MX31
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx31_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx27_clocks_init() has been used to register clocks on i.MX27
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx27_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A few words were misspelled in this comment.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix and add missing kerneldoc to fix compile warnings like:
drivers/clk/imx/clk-pfd.c:27: warning: Function parameter or member 'hw' not described in 'clk_pfd'
drivers/clk/imx/clk-pllv3.c:53: warning: Function parameter or member 'ref_clock' not described in 'clk_pllv3'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, Page 574, Chapter 5.2.6.4.3 Peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, for peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at offset 0xbf80 should be memrepair
clock, so correct it. And this clock should be always on
to make sure the memory repair function can works well.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at 0xbf00 is media_ldb clock,
not csi_phy2_ref, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the clock for CRC block allowing it to be enabled by consumers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description and
license to support building i.MX8QXP clock drivers as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description
and license to support building i.MX8M SoCs clock driver as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CONFIG_CLK_xxx for i.MX ARMv7 platforms, and use it as build option
instead of CONFIG_SOC_xxx, the CONFIG_CLK_xxx will be selected by default
according to CONFIG_SOC_xxx.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed() instead of __raw_readl(), and use BIT(x)
instead of (1 << X) to fix below build warning reported by kernel
test robot:
drivers/clk/imx/clk-imx6sl.c:149:49: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
while (!(__raw_readl(anatop_base + PLL_ARM) & BM_PLL_ARM_LOCK))
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
* clk-fallthru:
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
* clk-ingenic:
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
* clk-tegra:
clk: tegra: pll: Improve PLLM enable-state detection
* clk-sirf:
clk: clk-atlas6: fix return value check in atlas6_clk_init()
* clk-qoriq:
clk: qoriq: add LS1021A core pll mux options
Add mu root clk for mu mailbox usage.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the bus clk use imx8m_clk_hw_composite_bus, then
we could avoid possible issue when setting mux of the clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx8m_clk_hw_composite_bus api for bus clk root slice usage.
Because the mux switch sequence issue, we could not reuse Peripheral
Clock Slice code, need use composite specific mux operation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CORE/BUS root slice has following design, simplied graph:
The difference is core not have pre_div block.
A composite core/bus clk has 8 inputs for mux to select, saying clk[0-7].
It support target(smart) interface and normal interface. Target interface
is exported for programmer easy to configure ccm root. Normal interface
is also exported, but we not use it in our driver, because it will
introduce more complexity compared with target interface.
The normal interface simplified as below:
SEL_A GA
+--+ +-+
| +->+ +------+
CLK[0-7]--->+ | +-+ |
| | | +----v---+ +----+
| +--+ |pre_diva+----> | +---------+
| +--------+ |mux +--+post_div |
| +--+ |pre_divb+--->+ | +---------+
| | | +----^---+ +----+
+--->+ | +-+ |
| +->+ +------+
+--+ +-+
SEL_B GB
The mux in the upper pic is not the target interface MUX, target
interface MUX is hiding SEL_A and SEL_B. When you choose clk[0-7],
you are actually writing SEL_A or SEL_B depends on the internal
counter which will also control the internal "mux".
The target interface simplified as below which is used by Linux Kernel:
CLK[0-7]--->MUX-->Gate-->pre_div-->post_div
A requirement of the Target Interface's software is that the
target clock source is active, it means when setting SEL_A, the
current input clk to SEL_A must be active, same to SEL_B.
We touch target interface, but hardware logic actually also need
configure normal interface.
There will be system hang, when doing the following steps:
The initial state:
SEL_A/SEL_B are both sourcing from clk0, the internal counter
choose SEL_A.
1. switch mux from clk0 to clk1
The hardware logic will choose SEL_B and configure SEL_B to clk1.
SEL_A no changed.
2. gate off clk0
Disable clk0, then the input to SEL_A is off.
3. swtich from clk1 to clk2
The hardware logic will choose SEL_A and configure SEL_A to clk2,
however the current SEL_A input clk0 is off, the system hang.
The solution to fix the issue is in step 1, write twice to
target interface MUX, it will make SEL_A/SEL_B both sources
from clk1, then no need to care about the state of clk0. And
finally system performs well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
