IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 54f1840ddee9bbdc8dd89fbbfdfa632401244146 upstream.
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c896ff2dd8f30a6b0a922c83a96f6d43f05f0e92 upstream.
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6bfe ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb118de5003028ad092a4e66fc6d07b86c3bc94 upstream.
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc0ec46f6e7511fc4fdf6b6cda439382bc957f1 upstream.
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3171d37b58a76e1febbf3f4af2d06234a98cf88b upstream.
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0de ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b13e59e74ff71a1004e0508107e91e9a84fd7388 ]
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3914784553f68c931fc666dbe7e86fe881aada38 upstream.
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92e73d807b68b2214fcafca4e130b5300a9d4b3c ]
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0195fa9a9e263df204963f88a22b21688ffb66 ]
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac030 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fee465150b458351b6d9b9f66084f3cc3022b88b upstream.
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb98 ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69f035c480d76f12bf061148ccfd578e1099e5fc upstream.
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4caf4cb1eaed469742ef719f2cc024b1ec3fa9e6 upstream.
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a1038728037 ("i2c: iproc: add NIC I2C support")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05f933d5f7318b03ff2028c1704dc867ac16f2c7 ]
Since commit 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba
driver"), there is no more request_mem_region() call in this driver.
So remove the release_mem_region() call from the remove function which is
likely a left over.
Fixes: 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba driver")
Cc: <stable@vger.kernel.org> # v3.6+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c7174db4cdd111e10d19eed5c36fd978a14c8a2 ]
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e989578232da33a7fe96b04191b862af8b2cec ]
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding
size determination a bit safer according to the Linux coding style
convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b3b21a8542fd2fb6ffc61bc13b9419f0c58ebad ]
These issues were detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cd9489623c29aa2f8cc07088168afb6e0d5ef06d upstream.
Smatch Warns:
drivers/i2c/busses/i2c-qup.c:1784 qup_i2c_probe()
warn: missing unwind goto?
The goto label "fail_runtime" and "fail" will disable qup->pclk,
but here qup->pclk failed to obtain, in order to be consistent,
change the direct return to goto label "fail_dma".
Fixes: 9cedf3b2f099 ("i2c: qup: Add bam dma capabilities")
Signed-off-by: Shuai Jiang <d202180596@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb6e45c9a0ad9e0f8664fd06db0227d185dc76ab ]
In xiic_process, it is possible that error events such as arbitration
lost or TX error can be raised in conjunction with other interrupt flags
such as TX FIFO empty or bus not busy. Error events result in the
controller being reset and the error returned to the calling request,
but the function could potentially try to keep handling the other
events, such as by writing more messages into the TX FIFO. Since the
transaction has already failed, this is not helpful and will just cause
issues.
This problem has been present ever since:
commit 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
which allowed non-error events to be handled after errors, but became
more obvious after:
commit 743e227a8959 ("i2c: xiic: Defer xiic_wakeup() and
__xiic_start_xfer() in xiic_process()")
which reworked the code to add a WARN_ON which triggers if both the
xfer_more and wakeup_req flags were set, since this combination is
not supposed to happen, but was occurring in this scenario.
Skip further interrupt handling after error flags are detected to avoid
this problem.
Fixes: 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743e227a895923c37a333eb2ebf3e391f00c406d ]
The __xiic_start_xfer() manipulates the interrupt flags, xiic_wakeup()
may result in return from xiic_xfer() early. Defer both to the end of
the xiic_process() interrupt thread, so that they are executed after
all the other interrupt bits handling completed and once it completely
safe to perform changes to the interrupt bits in the hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: cb6e45c9a0ad ("i2c: xiic: Don't try to handle more interrupt events after error")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e69b9bc170c6d93ee375a5cbfd15f74c0fb59bdd ]
Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca0aa17f2db3468fd017038d23a78e17388e2f67 ]
If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.
So only skip clk disabling if resume failed, but do delete the adapter.
Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae1664f04f504a998737f5bb563f16b44357bcca ]
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 1a351b10b967 ("i2c: cadence: Added slave support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c770657bd2611b077ec1e7b1fe6aa92f249399bd upstream.
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 3b2f8f82dad7 ("i2c: omap: switch to threaded IRQ support")
Signed-off-by: Reid Tonking <reidt@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8160d3b35fc94491bb0cb974dbda310ef96c0e2 ]
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0efa8 ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 987dd36c0141f6ab9f0fbf14d6b2ec3342dedb2f ]
When start sending a new message clear the Rx & Tx buffer pointers in
order to avoid using stale pointers.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92fbb6d1296f81f41f65effd7f5f8c0f74943d15 upstream.
The data->block[0] variable comes from user and is a number between
0-255. Without proper check, the variable may be very large to cause
an out-of-bounds when performing memcpy in slimpro_i2c_blkwr.
Fix this bug by checking the value of writelen.
Fixes: f6505fbabc42 ("i2c: add SLIMpro I2C device driver on APM X-Gene platform")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c7885004567e8951d65a983be095f254dd20bef ]
When reading from I2C, the Tx watermark is set to 0. Unfortunately the
TDF (transmit data flag) is enabled when Tx FIFO entries is equal or less
than watermark. So it is set in every case, hence the reset default of 1.
This results in the MSR_RDF _and_ MSR_TDF flags to be set thus trying
to send Tx data on a read message.
Mask the IRQ status to filter for wanted flags only.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0582d984793d30442da88fe458674502bad1ad29 ]
Fix multiple W=1 kernel-doc warnings in i2c-rk3x.c:
drivers/i2c/busses/i2c-rk3x.c:83: warning: missing initial short description on line:
* struct i2c_spec_values:
drivers/i2c/busses/i2c-rk3x.c:139: warning: missing initial short description on line:
* struct rk3x_i2c_calced_timings:
drivers/i2c/busses/i2c-rk3x.c:162: warning: missing initial short description on line:
* struct rk3x_i2c_soc_data:
drivers/i2c/busses/i2c-rk3x.c:242: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a START condition, which triggers a REG_INT_START interrupt.
drivers/i2c/busses/i2c-rk3x.c:261: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
drivers/i2c/busses/i2c-rk3x.c:304: warning: expecting prototype for Setup a read according to i2c(). Prototype was for rk3x_i2c_prepare_read() instead
drivers/i2c/busses/i2c-rk3x.c:335: warning: expecting prototype for Fill the transmit buffer with data from i2c(). Prototype was for rk3x_i2c_fill_transmit_buf() instead
drivers/i2c/busses/i2c-rk3x.c:535: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Get timing values of I2C specification
drivers/i2c/busses/i2c-rk3x.c:552: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate divider values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:713: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate timing values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:963: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Setup I2C registers for an I2C operation specified by msgs, num.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78a4471fa1a76a8bef4919105de67660a89a1e9b ]
During boot of I2SE Duckbill the kernel log contains a
confusing error:
Failed to request dma
This is caused by i2c-mxs tries to request a not yet available DMA
channel (-EPROBE_DEFER). So suppress this message by using
dev_err_probe().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c37bc514514999e62a17e95160ed9ebf75ca8d ]
In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow
by depending on the values of the given parameters including the ic_clk.
For example in our use case where ic_clk is larger than one million,
multiplication of ic_clk * 4700 will result in 32 bit overflow.
Add cast of u64 to the calculation to avoid multiplication overflow, and
use the corresponding define for divide.
Fixes: 2373f6b9744d ("i2c-designware: split of i2c-designware.c into core and bus specific parts")
Signed-off-by: Lareine Khawaly <lareine@amazon.com>
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c045214a0f31dd5d6be716ed2f119b57b6c5d3a2 ]
Instead of open-coding DIV_ROUND_CLOSEST() and similar use the macros directly.
While at it, replace numbers with predefined SI metric prefixes.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: c8c37bc51451 ("i2c: designware: use casting of u64 in clock multiplication to avoid overflow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39244cc754829bf707dccd12e2ce37510f5b1f8d ]
When the driver does not check the data from the user, the variable
'data->block[0]' may be very large to cause an out-of-bounds bug.
The following log can reveal it:
[ 33.995542] i2c i2c-1: ioctl, cmd=0x720, arg=0x7ffcb3dc3a20
[ 33.995978] ismt_smbus 0000:00:05.0: I2C_SMBUS_BLOCK_DATA: WRITE
[ 33.996475] ==================================================================
[ 33.996995] BUG: KASAN: out-of-bounds in ismt_access.cold+0x374/0x214b
[ 33.997473] Read of size 18446744073709551615 at addr ffff88810efcfdb1 by task ismt_poc/485
[ 33.999450] Call Trace:
[ 34.001849] memcpy+0x20/0x60
[ 34.002077] ismt_access.cold+0x374/0x214b
[ 34.003382] __i2c_smbus_xfer+0x44f/0xfb0
[ 34.004007] i2c_smbus_xfer+0x10a/0x390
[ 34.004291] i2cdev_ioctl_smbus+0x2c8/0x710
[ 34.005196] i2cdev_ioctl+0x5ec/0x74c
Fix this bug by checking the size of 'data->block[0]' first.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d47b79d2bd39cc6369eccf94a06568d84c906ae ]
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: b3fdd32799d8 ("i2c: mux: Add register-based mux i2c-mux-reg")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36678f7905cbd1dc55a8a96e066dafd749d4600 ]
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e70 ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145900cf91c4b32ac05dbc8675a0c7f4a278749d ]
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
npcm_i2c_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6643d7207c572c1b0305ed505101f15502c6c87 ]
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdbf26251d3b35c4ccaea0c3a6de4318f727d3d2 ]
When the I2C controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the I2C controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
This fixes an issue where the DMA engine's SMMU stream ID needs to be
misleadingly set for the I2C controllers in device tree.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 569bea74c94d37785682b11bab76f557520477cd ]
In piix4_probe(), the piix4 adapter will be registered in:
piix4_probe()
piix4_add_adapters_sb800() / piix4_add_adapter()
i2c_add_adapter()
Based on the probed device type, piix4_add_adapters_sb800() or single
piix4_add_adapter() will be called.
For the former case, piix4_adapter_count is set as the number of adapters,
while for antoher case it is not set and kept default *zero*.
When piix4 is removed, piix4_remove() removes the adapters added in
piix4_probe(), basing on the piix4_adapter_count value.
Because the count is zero for the single adapter case, the adapter won't
be removed and makes the sources allocated for adapter leaked, such as
the i2c client and device.
These sources can still be accessed by i2c or bus and cause problems.
An easily reproduced case is that if a new adapter is registered, i2c
will get the leaked adapter and try to call smbus_algorithm, which was
already freed:
Triggered by: rmmod i2c_piix4 && modprobe max31730
BUG: unable to handle page fault for address: ffffffffc053d860
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 3752 Comm: modprobe Tainted: G
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:i2c_default_probe (drivers/i2c/i2c-core-base.c:2259) i2c_core
RSP: 0018:ffff888107477710 EFLAGS: 00000246
...
<TASK>
i2c_detect (drivers/i2c/i2c-core-base.c:2302) i2c_core
__process_new_driver (drivers/i2c/i2c-core-base.c:1336) i2c_core
bus_for_each_dev (drivers/base/bus.c:301)
i2c_for_each_dev (drivers/i2c/i2c-core-base.c:1823) i2c_core
i2c_register_driver (drivers/i2c/i2c-core-base.c:1861) i2c_core
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
</TASK>
---[ end trace 0000000000000000 ]---
Fix this problem by correctly set piix4_adapter_count as 1 for the
single adapter so it can be normally removed.
Fixes: 528d53a1592b ("i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8caf0a0e04583fb71e21495bef84509182227ea ]
The missing "platform" alias is required for the mgb4 v4l2 driver to load
the i2c controller driver when probing the HW.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61775d54d674ff8ec3658495e0dbc537227dc5c1 upstream.
When we compile-in the CCI along with the imx412 driver and run on the RB5
we see that i2c_add_adapter() causes the probe of the imx412 driver to
happen.
This probe tries to perform an i2c xfer() and the xfer() in i2c-qcom-cci.c
fails on pm_runtime_get() because the i2c-qcom-cci.c::probe() function has
not completed to pm_runtime_enable(dev).
Fix this sequence by ensuring pm_runtime_xxx() calls happen prior to adding
the i2c adapter.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86067ccfa1424a26491542d6f6d7546d40b61a10 ]
Linux is not the only entity using the BlueField I2C busses so
support a lock mechanism provided by hardware to avoid issues
when multiple entities are trying to access the same bus.
The lock is acquired whenever written explicitely or the lock
register is read. So make sure it is always released at the end
of a successful or failed transaction.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f071ec327b04c83d47637c5e5c2199b39899ca ]
The i2c-mlxbf.c driver is currently broken because there is a bug
in the calculation of the frequency. core_f, core_r and core_od
are components read from hardware registers and are used to
compute the frequency used to compute different timing parameters.
The shifting mechanism used to get core_f, core_r and core_od is
wrong. Use FIELD_GET to mask and shift the bitfields properly.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de24aceb07d426b6f1c59f33889d6a964770547b ]
memcpy() is called in a loop while 'operation->length' upper bound
is not checked and 'data_idx' also increments.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5be6d1340c0fefcee8a6489cff7fd88a0d5b85 ]
Correct the base address used during io write.
This bug had no impact over the overall functionality of the read and write
transactions. MLXBF_I2C_CAUSE_OR_CLEAR=0x18 so writing to (smbus->io + 0x18)
instead of (mst_cause->ioi + 0x18) actually writes to the sc_low_timeout
register which just sets the timeout value before a read/write aborts.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 085aacaa73163f4b8a89dec24ecb32cfacd34017 ]
pm_runtime_get_sync() returning 1 also means the device is powered. So
resetting the chip registers in .remove() is possible and should be
done.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d98bdd3a5b50 ("i2c: imx: Make sure to unregister adapter on remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d98bdd3a5b50446d8e010be5b04ce81c4eabf728 upstream.
If for whatever reasons pm_runtime_resume_and_get() fails and .remove() is
exited early, the i2c adapter stays around and the irq still calls its
handler, while the driver data and the register mapping go away. So if
later the i2c adapter is accessed or the irq triggers this results in
havoc accessing freed memory and unmapped registers.
So unregister the software resources even if resume failed, and only skip
the hardware access in that case.
Fixes: 588eb93ea49f ("i2c: imx: add runtime pm support to improve the performance")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6435319c34704994e19b0767f6a4e6f37439867b ]
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdf6d97f03035ad5298e2d1635036c74c2090ed ]
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
