IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 61b40cefe51af005c72dbdcf975a3d166c6e6406 upstream.
In bcm_sf2_mdio_register(), the class_find_device() will call get_device()
to increment reference count for priv->master_mii_bus->dev if
of_mdio_find_bus() succeeds. If mdiobus_alloc() or mdiobus_register()
fails, it will call get_device() twice without decrement reference count
for the device. And it is the same if bcm_sf2_mdio_register() succeeds but
fails in bcm_sf2_sw_probe(), or if bcm_sf2_sw_probe() succeeds. If the
reference count has not decremented to zero, the dev related resource will
not be freed.
So remove the get_device() in bcm_sf2_mdio_register(), and call
put_device() if mdiobus_alloc() or mdiobus_register() fails and in
bcm_sf2_mdio_unregister() to solve the issue.
And as Simon suggested, unwind from errors for bcm_sf2_mdio_register() and
just return 0 if it succeeds to make it cleaner.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231011032419.2423290-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ccf50d4d4741e064ba35511a95402c63bbe21a8 ]
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894cafc5c62ccced758077bd4e970dc714c42637 ]
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a9b ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 954ad9bf13c4f95a4958b5f8433301f2ab99e1f5 ]
More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.
The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.
The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".
Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".
So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.
I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.
So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.
Some numerical data points:
40Mbps stream, max interfering frame size 1500, port speed 100M
---------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -60000 locredit -900 hicredit 600
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 600 600
credit_lo 900 900
send_slope 7500000 75
idle_slope 5000000 50
40Mbps stream, max interfering frame size 1500, port speed 1G
-------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -960000 locredit -1440 hicredit 60
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 60 60
credit_lo 1440 1440
send_slope 120000000 120
idle_slope 5000000 5
5.12Mbps stream, max interfering frame size 1522, port speed 100M
-----------------------------------------------------------------
tc-cbs parameters:
idleslope 5120 sendslope -94880 locredit -1444 hicredit 77
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 77 77
credit_lo 1444 1444
send_slope 11860000 118
idle_slope 640000 6
Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.
Fixes: 4d7525085a9b ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12dcd23d052a4927195f15e970e27ab26 ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e70c ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dadc5b86cc9459581f37fe755b431adc399ea393 ]
in bcm_sf2_sw_probe(), check the return value of clk_prepare_enable()
and return the error code if clk_prepare_enable() returns an
unexpected value.
Fixes: e9ec5c3bd238 ("net: dsa: bcm_sf2: request and handle clocks")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230726170506.16547-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf62c8177adb0db9e15c8b898c44f997acf3ebf ]
Switch in MAXLEN register stores the maximum size of a data frame.
The MTU size is 18 bytes smaller than the frame size.
The current settings are causing problems with packet forwarding.
This patch fixes the MTU settings to proper values.
Fixes: fb77ffc6ec86 ("net: dsa: vsc73xx: make the MTU configurable")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230628194327.1765644-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae90f90e4909e3014e2dc6a0627964617a7b824 ]
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a59a58ec25d44f853c26bdbfda47d73b3067435 ]
LAN9303 doesn't associate FDB (ALR) entries with VLANs, it has just one
global Address Logic Resolution table [1].
Ignore VID in port_fdb_{add|del} methods, go on with the global table. This
is the same semantics as hellcreek or RZ/N1 implement.
Visible symptoms:
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to delete 00:xx:xx:xx:xx:cf vid 1 from fdb: -2
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to add 00:xx:xx:xx:xx:cf vid 1 to fdb: -95
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002308A.pdf
Fixes: 0620427ea0d6 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230531143826.477267-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c27f3d53d588618d81d30d6712459a3cc9489b8 ]
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c218d8021e36e226add4bab93d071d30fe0704 ]
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d237 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45977e58ce65ed0459edc9a0466d9dfea09463f5 ]
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bcad0f0e6fbc1d613e49e0ee35c8e5f2e685bb0 ]
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e9517375a14f44ee830ca1c3278076dd65fcc8f ]
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c977c5c2e4c5d8ad1b604724cc344e38f96fe9b ]
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230118174735.702377-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8964916d206071b058c6351f88b1966bd58cbde0 ]
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f59bca275d2d819a8788c0f962e9e89843efc9 ]
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 633efc8b3dc96f56f5a57f2a49764853a2fa3f50 ]
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 42bc4fafe359ed6b73602b7a2dba0dd99588f8ce upstream.
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04ec4e6250e5f58b525b08f3dca45c7d7427620e ]
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f7f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fd8e899cdb5ecaf8e8ee73854a99e10807eef1de upstream.
If an error occurs in dsa_devlink_region_create(), then 'priv->regions'
array will be accessed by negative index '-1'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: bf425b82059e ("net: dsa: sja1105: expose static config as devlink region")
Link: https://lore.kernel.org/r/20220817003845.389644-1-subkhankulov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d21c4565bce064c73a03b79a157a3493c518b9 upstream.
What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36c0d935015766bf20d621c18313f17691bda5e3 upstream.
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 246bbf2f977ea36aaf41f5d24370fef433250728 upstream.
If the port isn't a CPU port nor a user port, 'cpu_dp'
is a null pointer and a crash happened on dereferencing
it in mv88e6060_setup_port():
[ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014
...
[ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84
[ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54
[ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0
[ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c
[ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c
[ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0
[ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184
[ 9.986632] __device_attach from bus_probe_device+0x8c/0x94
[ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8
[ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c
[ 10.006292] process_one_work from worker_thread+0x30/0x4b8
[ 10.012155] worker_thread from kthread+0xd4/0x10c
[ 10.017238] kthread from ret_from_fork+0x14/0x3c
Fixes: 0abfd494deef ("net: dsa: use dedicated CPU port")
CC: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220811070939.1717146-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c97bc0128b2eecc703106112679a69d446d1a12 upstream.
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0737e018a05e2aa352828c52bdeed3b02cff2930 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
when breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the gphy_fw_np.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605072335.11257-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02ded5a173619b11728b8bf75a3fd995a2c1ff28 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66f862563ed68717dfd84e808ca12705ed275ced ]
When using an external PHY connected using RGMII to mt7531 port 5, the
PHY can be used to used support 1000BASE-X connections. Moreover, if
1000BASE-T is supported, then we should allow 1000BASE-X as well, since
which are supported is a property of the PHY.
Therefore, it makes no sense to exclude this from the linkmodes when
1000BASE-T is supported.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7be130c5d52e5224ac7d89568737b37b4c4b785 ]
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220512021731.2494261-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71cffebf6358a7f5031f5b208bbdc1cb4db6e539 ]
Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6934e4048c91502efcb21da92b7ae37cd8fa741 ]
The DSA master might not have been probed yet in which case the probe of
the felix switch fails with -EPROBE_DEFER:
[ 4.435305] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
It is not an error. Use dev_err_probe() to demote this particular error
to a debug message.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220408101521.281886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6da69b1da130e7d96766042750cd9f902e890eba ]
The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585d42bb57bb358d48906660a8de273b078810b1 ]
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e981bc74aefc6a177b50c16cfa7023599799cf74 ]
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5417cbf7ab5df1632e68fe7d9e6331fc0e7dbd6 ]
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6bb9681a43f34f2cab4aad6e2a02da4ce54d13c5 upstream.
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51a04ebf21122d5c76a716ecd9bfc33ea44b2b39 ]
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893b2 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d120dfb5d67edc5bcd1804e167dba2b30809afd ]
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bdb7ec6a28c7cdf580a0a98afbc9fc3b98932 ]
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08f1a20822349004bb9cc1b153ecb516e9f2889d ]
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50facd86e9fbc4b93fe02e5fe05776047f45dbfb ]
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f53a2ce893b2c7884ef94471f170839170a4eba0 ]
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4223f86512877b04c932e7203648b37eec931731 upstream.
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f5f12f5d4b108399130bb5c11f07765851d9cdb ]
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 342afce10d6f61c443c95e244f812d4766f73f53 upstream.
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
