IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 5c0930ccaad5a74d74e8b18b648c5eb21ed2fe94 ]
2b8272ff4a70 ("cpu/hotplug: Prevent self deadlock on CPU hot-unplug")
solved the straight forward CPU hotplug deadlock vs. the scheduler
bandwidth timer. Yu discovered a more involved variant where a task which
has a bandwidth timer started on the outgoing CPU holds a lock and then
gets throttled. If the lock required by one of the CPU hotplug callbacks
the hotplug operation deadlocks because the unthrottling timer event is not
handled on the dying CPU and can only be recovered once the control CPU
reaches the hotplug state which pulls the pending hrtimers from the dead
CPU.
Solve this by pushing the hrtimers away from the dying CPU in the dying
callbacks. Nothing can queue a hrtimer on the dying CPU at that point because
all other CPUs spin in stop_machine() with interrupts disabled and once the
operation is finished the CPU is marked offline.
Reported-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Liu Tie <liutie4@huawei.com>
Link: https://lore.kernel.org/r/87a5rphara.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 62c1256d544747b38e77ca9b5bfe3a26f9592576 upstream.
When tick_nohz_stop_tick() stops the tick and high resolution timers are
disabled, then the clock event device is not put into ONESHOT_STOPPED
mode. This can lead to spurious timer interrupts with some clock event
device drivers that don't shut down entirely after firing.
Eliminate these by putting the device into ONESHOT_STOPPED mode at points
where it is not being reprogrammed. When there are no timers active, then
tick_program_event() with KTIME_MAX can be used to stop the device. When
there is a timer active, the device can be stopped at the next tick (any
new timer added by timers will reprogram the tick).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220422141446.915024-1-npiggin@gmail.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1ff03cd6fb9c501fff63a4a2bface9adcfa81cd upstream.
On some rare cases, the timekeeper CPU may be delaying its jiffies
update duty for a while. Known causes include:
* The timekeeper is waiting on stop_machine in a MULTI_STOP_DISABLE_IRQ
or MULTI_STOP_RUN state. Disabled interrupts prevent from timekeeping
updates while waiting for the target CPU to complete its
stop_machine() callback.
* The timekeeper vcpu has VMEXIT'ed for a long while due to some overload
on the host.
Detect and fix these situations with emergency timekeeping catchups.
Original-patch-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ce8849dd1e78dadcee0ec9acbd259d239b7069f ]
posix_timer_add() tries to allocate a posix timer ID by starting from the
cached ID which was stored by the last successful allocation.
This is done in a loop searching the ID space for a free slot one by
one. The loop has to terminate when the search wrapped around to the
starting point.
But that's racy vs. establishing the starting point. That is read out
lockless, which leads to the following problem:
CPU0 CPU1
posix_timer_add()
start = sig->posix_timer_id;
lock(hash_lock);
... posix_timer_add()
if (++sig->posix_timer_id < 0)
start = sig->posix_timer_id;
sig->posix_timer_id = 0;
So CPU1 can observe a negative start value, i.e. -1, and the loop break
never happens because the condition can never be true:
if (sig->posix_timer_id == start)
break;
While this is unlikely to ever turn into an endless loop as the ID space is
huge (INT_MAX), the racy read of the start value caught the attention of
KCSAN and Dmitry unearthed that incorrectness.
Rewrite it so that all id operations are under the hash lock.
Reported-by: syzbot+5c54bd3eb218bb595aa9@syzkaller.appspotmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/87bkhzdn6g.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d9e522010eb5685d8b53e8a24320653d9d4cbbf ]
itimer_delete() has a retry loop when the timer is concurrently expired. On
non-RT kernels this just spin-waits until the timer callback has completed,
except for posix CPU timers which have HAVE_POSIX_CPU_TIMERS_TASK_WORK
enabled.
In that case and on RT kernels the existing task could live lock when
preempting the task which does the timer delivery.
Replace spin_unlock() with an invocation of timer_wait_running() to handle
it the same way as the other retry loops in the posix timer code.
Fixes: ec8f954a40da ("posix-timers: Use a callback for cancel synchronization on PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/87v8g7c50d.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 13bb06f8dd42071cb9a49f6e21099eea05d4b856 upstream.
The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.
The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().
With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.
Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.
[bigeasy: Patch description + testing].
Fixes: e9523a0d81899 ("tick/common: Align tick period with the HZ tick.")
Reported-by: Mathias Krause <minipli@grsecurity.net>
Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com>
Suggested-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Mathias Krause <minipli@grsecurity.net>
Acked-by: SeongJae Park <sj@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net
Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com
Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9523a0d81899361214d118ad60ef76f0e92f71d ]
With HIGHRES enabled tick_sched_timer() is programmed every jiffy to
expire the timer_list timers. This timer is programmed accurate in
respect to CLOCK_MONOTONIC so that 0 seconds and nanoseconds is the
first tick and the next one is 1000/CONFIG_HZ ms later. For HZ=250 it is
every 4 ms and so based on the current time the next tick can be
computed.
This accuracy broke since the commit mentioned below because the jiffy
based clocksource is initialized with higher accuracy in
read_persistent_wall_and_boot_offset(). This higher accuracy is
inherited during the setup in tick_setup_device(). The timer still fires
every 4ms with HZ=250 but timer is no longer aligned with
CLOCK_MONOTONIC with 0 as it origin but has an offset in the us/ns part
of the timestamp. The offset differs with every boot and makes it
impossible for user land to align with the tick.
Align the tick period with CLOCK_MONOTONIC ensuring that it is always a
multiple of 1000/CONFIG_HZ ms.
Fixes: 857baa87b6422 ("sched/clock: Enable sched clock early")
Reported-by: Gusenleitner Klaus <gus@keba.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/20230406095735.0_14edn3@linutronix.de
Link: https://lore.kernel.org/r/20230418122639.ikgfvu3f@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b996544916429946bf4934c1c01a306d1690972c ]
The variable tick_period is initialized to NSEC_PER_TICK / HZ during boot
and never updated again.
If NSEC_PER_TICK is not an integer multiple of HZ this computation is less
accurate than TICK_NSEC which has proper rounding in place.
Aside of the inaccuracy there is no reason for having this variable at
all. It's just a pointless indirection and all usage sites can just use the
TICK_NSEC constant.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.766643526@linutronix.de
Stable-dep-of: e9523a0d8189 ("tick/common: Align tick period with the HZ tick.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a35bf2a6a871cd0252cd371d741e7d070b53af9 ]
Now that it's clear that there is always one tick to account, simplify the
calculations some more.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.565663056@linutronix.de
Stable-dep-of: e9523a0d8189 ("tick/common: Align tick period with the HZ tick.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94ad2e3cedb82af034f6d97c58022f162b669f9b ]
If jiffies are up to date already (caller lost the race against another
CPU) there is no point to change the sequence count. Doing that just forces
other CPUs into the seqcount retry loop in tick_nohz_next_event() for
nothing.
Just bail out early.
[ tglx: Rewrote most of it ]
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.462195901@linutronix.de
Stable-dep-of: e9523a0d8189 ("tick/common: Align tick period with the HZ tick.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372acbbaa80940189593f9d69c7c069955f24f7a ]
No point in doing calculations.
tick_next_period = last_jiffies_update + tick_period
Just check whether now is before tick_next_period to figure out whether
jiffies need an update.
Add a comment why the intentional data race in the quick check is safe or
not so safe in a 32bit corner case and why we don't worry about it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201117132006.337366695@linutronix.de
Stable-dep-of: e9523a0d8189 ("tick/common: Align tick period with the HZ tick.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 58d7668242647e661a20efe065519abd6454287e upstream.
For CONFIG_NO_HZ_FULL systems, the tick_do_timer_cpu cannot be offlined.
However, cpu_is_hotpluggable() still returns true for those CPUs. This causes
torture tests that do offlining to end up trying to offline this CPU causing
test failures. Such failure happens on all architectures.
Fix the repeated error messages thrown by this (even if the hotplug errors are
harmless) by asking the opinion of the nohz subsystem on whether the CPU can be
hotplugged.
[ Apply Frederic Weisbecker feedback on refactoring tick_nohz_cpu_down(). ]
For drivers/base/ portion:
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Zhouyi Zhou <zhouzhouyi@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: rcu <rcu@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 2987557f52b9 ("driver-core/cpu: Expose hotpluggability to the rest of the kernel")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7abf14f0001a5a47539d9f60bbdca649e43536b upstream.
For some unknown reason the introduction of the timer_wait_running callback
missed to fixup posix CPU timers, which went unnoticed for almost four years.
Marco reported recently that the WARN_ON() in timer_wait_running()
triggers with a posix CPU timer test case.
Posix CPU timers have two execution models for expiring timers depending on
CONFIG_POSIX_CPU_TIMERS_TASK_WORK:
1) If not enabled, the expiry happens in hard interrupt context so
spin waiting on the remote CPU is reasonably time bound.
Implement an empty stub function for that case.
2) If enabled, the expiry happens in task work before returning to user
space or guest mode. The expired timers are marked as firing and moved
from the timer queue to a local list head with sighand lock held. Once
the timers are moved, sighand lock is dropped and the expiry happens in
fully preemptible context. That means the expiring task can be scheduled
out, migrated, interrupted etc. So spin waiting on it is more than
suboptimal.
The timer wheel has a timer_wait_running() mechanism for RT, which uses
a per CPU timer-base expiry lock which is held by the expiry code and the
task waiting for the timer function to complete blocks on that lock.
This does not work in the same way for posix CPU timers as there is no
timer base and expiry for process wide timers can run on any task
belonging to that process, but the concept of waiting on an expiry lock
can be used too in a slightly different way:
- Add a mutex to struct posix_cputimers_work. This struct is per task
and used to schedule the expiry task work from the timer interrupt.
- Add a task_struct pointer to struct cpu_timer which is used to store
a the task which runs the expiry. That's filled in when the task
moves the expired timers to the local expiry list. That's not
affecting the size of the k_itimer union as there are bigger union
members already
- Let the task take the expiry mutex around the expiry function
- Let the waiter acquire a task reference with rcu_read_lock() held and
block on the expiry mutex
This avoids spin-waiting on a task which might not even be on a CPU and
works nicely for RT too.
Fixes: ec8f954a40da ("posix-timers: Use a callback for cancel synchronization on PREEMPT_RT")
Reported-by: Marco Elver <elver@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marco Elver <elver@google.com>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87zg764ojw.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7082cdfc464bf9231300605d03eebf943dda307 ]
Bugs have been reported on 8 sockets x86 machines in which the TSC was
wrongly disabled when the system is under heavy workload.
[ 818.380354] clocksource: timekeeping watchdog on CPU336: hpet wd-wd read-back delay of 1203520ns
[ 818.436160] clocksource: wd-tsc-wd read-back delay of 181880ns, clock-skew test skipped!
[ 819.402962] clocksource: timekeeping watchdog on CPU338: hpet wd-wd read-back delay of 324000ns
[ 819.448036] clocksource: wd-tsc-wd read-back delay of 337240ns, clock-skew test skipped!
[ 819.880863] clocksource: timekeeping watchdog on CPU339: hpet read-back delay of 150280ns, attempt 3, marking unstable
[ 819.936243] tsc: Marking TSC unstable due to clocksource watchdog
[ 820.068173] TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
[ 820.092382] sched_clock: Marking unstable (818769414384, 1195404998)
[ 820.643627] clocksource: Checking clocksource tsc synchronization from CPU 267 to CPUs 0,4,25,70,126,430,557,564.
[ 821.067990] clocksource: Switched to clocksource hpet
This can be reproduced by running memory intensive 'stream' tests,
or some of the stress-ng subcases such as 'ioport'.
The reason for these issues is the when system is under heavy load, the
read latency of the clocksources can be very high. Even lightweight TSC
reads can show high latencies, and latencies are much worse for external
clocksources such as HPET or the APIC PM timer. These latencies can
result in false-positive clocksource-unstable determinations.
These issues were initially reported by a customer running on a production
system, and this problem was reproduced on several generations of Xeon
servers, especially when running the stress-ng test. These Xeon servers
were not production systems, but they did have the latest steppings
and firmware.
Given that the clocksource watchdog is a continual diagnostic check with
frequency of twice a second, there is no need to rush it when the system
is under heavy load. Therefore, when high clocksource read latencies
are detected, suspend the watchdog timer for 5 minutes.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Waiman Long <longman@redhat.com>
Cc: John Stultz <jstultz@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f76d59173d9d146e96c66886b671c1915a5c5e5 ]
The nanosleep syscalls use the restart_block mechanism, with a quirk:
The `type` and `rmtp`/`compat_rmtp` fields are set up unconditionally on
syscall entry, while the rest of the restart_block is only set up in the
unlikely case that the syscall is actually interrupted by a signal (or
pseudo-signal) that doesn't have a signal handler.
If the restart_block was set up by a previous syscall (futex(...,
FUTEX_WAIT, ...) or poll()) and hasn't been invalidated somehow since then,
this will clobber some of the union fields used by futex_wait_restart() and
do_restart_poll().
If userspace afterwards wrongly calls the restart_syscall syscall,
futex_wait_restart()/do_restart_poll() will read struct fields that have
been clobbered.
This doesn't actually lead to anything particularly interesting because
none of the union fields contain trusted kernel data, and
futex(..., FUTEX_WAIT, ...) and poll() aren't syscalls where it makes much
sense to apply seccomp filters to their arguments.
So the current consequences are just of the "if userspace does bad stuff,
it can damage itself, and that's not a problem" flavor.
But still, it seems like a hazard for future developers, so invalidate the
restart_block when partly setting it up in the nanosleep syscalls.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230105134403.754986-1-jannh@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d125d1349abeb46945dc5e98f7824bf688266f13 upstream.
syzbot reported a RCU stall which is caused by setting up an alarmtimer
with a very small interval and ignoring the signal. The reproducer arms the
alarm timer with a relative expiry of 8ns and an interval of 9ns. Not a
problem per se, but that's an issue when the signal is ignored because then
the timer is immediately rearmed because there is no way to delay that
rearming to the signal delivery path. See posix_timer_fn() and commit
58229a189942 ("posix-timers: Prevent softirq starvation by small intervals
and SIG_IGN") for details.
The reproducer does not set SIG_IGN explicitely, but it sets up the timers
signal with SIGCONT. That has the same effect as explicitely setting
SIG_IGN for a signal as SIGCONT is ignored if there is no handler set and
the task is not ptraced.
The log clearly shows that:
[pid 5102] --- SIGCONT {si_signo=SIGCONT, si_code=SI_TIMER, si_timerid=0, si_overrun=316014, si_int=0, si_ptr=NULL} ---
It works because the tasks are traced and therefore the signal is queued so
the tracer can see it, which delays the restart of the timer to the signal
delivery path. But then the tracer is killed:
[pid 5087] kill(-5102, SIGKILL <unfinished ...>
...
./strace-static-x86_64: Process 5107 detached
and after it's gone the stall can be observed:
syzkaller login: [ 79.439102][ C0] hrtimer: interrupt took 68471 ns
[ 184.460538][ C1] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
...
[ 184.658237][ C1] rcu: Stack dump where RCU GP kthread last ran:
[ 184.664574][ C1] Sending NMI from CPU 1 to CPUs 0:
[ 184.669821][ C0] NMI backtrace for cpu 0
[ 184.669831][ C0] CPU: 0 PID: 5108 Comm: syz-executor192 Not tainted 6.2.0-rc6-next-20230203-syzkaller #0
...
[ 184.670036][ C0] Call Trace:
[ 184.670041][ C0] <IRQ>
[ 184.670045][ C0] alarmtimer_fired+0x327/0x670
posix_timer_fn() prevents that by checking whether the interval for
timers which have the signal ignored is smaller than a jiffie and
artifically delay it by shifting the next expiry out by a jiffie. That's
accurate vs. the overrun accounting, but slightly inaccurate
vs. timer_gettimer(2).
The comment in that function says what needs to be done and there was a fix
available for the regular userspace induced SIG_IGN mechanism, but that did
not work due to the implicit ignore for SIGCONT and similar signals. This
needs to be worked on, but for now the only available workaround is to do
exactly what posix_timer_fn() does:
Increase the interval of self-rearming timers, which have their signal
ignored, to at least a jiffie.
Interestingly this has been fixed before via commit ff86bf0c65f1
("alarmtimer: Rate limit periodic intervals") already, but that fix got
lost in a later rework.
Reported-by: syzbot+b9564ba6e8e00694511b@syzkaller.appspotmail.com
Fixes: f2c45807d399 ("alarmtimer: Switch over to generic set/get/rearm routine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87k00q1no2.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8ac29b40183a6038919768b5d189c9bd91ce9b4 ]
The rng's random_init() function contributes the real time to the rng at
boot time, so that events can at least start in relation to something
particular in the real world. But this clock might not yet be set that
point in boot, so nothing is contributed. In addition, the relation
between minor clock changes from, say, NTP, and the cycle counter is
potentially useful entropic data.
This commit addresses this by mixing in a time stamp on calls to
settimeofday and adjtimex. No entropy is credited in doing so, so it
doesn't make initialization faster, but it is still useful input to
have.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151c8e499f4705010780189377f85b57400ccbf5 ]
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5b36a4dbd06c5e8e36ca8ccc552f679069e2946 upstream.
As Chris explains, the comment above exit_itimers() is not correct,
we can race with proc_timers_seq_ops. Change exit_itimers() to clear
signal->posix_timers with ->siglock held.
Cc: <stable@vger.kernel.org>
Reported-by: chris@accessvector.net
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2390095113e98fc52fffe35c5206d30d9efe3f78 upstream.
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it had been broken for a decade.
Commit 28438794aba4 ("modpost: fix section mismatch check for exported
init/exit sections") fixed it so modpost started to warn it again, then
this showed up:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab_gpl+tick_nohz_full_setup+0x0): Section mismatch in reference from the variable __ksymtab_tick_nohz_full_setup to the function .init.text:tick_nohz_full_setup()
The symbol tick_nohz_full_setup is exported and annotated __init
Fix this by removing the __init annotation of tick_nohz_full_setup or drop the export.
Drop the export because tick_nohz_full_setup() is only called from the
built-in code in kernel/sched/isolation.c.
Fixes: ae9e557b5be2 ("time: Export tick start/stop functions for rcutorture")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Backlund <tmb@tmb.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1366992e16bddd5e2d9a561687f367f9f802e2e4 upstream.
The addition of random_get_entropy_fallback() provides access to
whichever time source has the highest frequency, which is useful for
gathering entropy on platforms without available cycle counters. It's
not necessarily as good as being able to quickly access a cycle counter
that the CPU has, but it's still something, even when it falls back to
being jiffies-based.
In the event that a given arch does not define get_cycles(), falling
back to the get_cycles() default implementation that returns 0 is really
not the best we can do. Instead, at least calling
random_get_entropy_fallback() would be preferable, because that always
needs to return _something_, even falling back to jiffies eventually.
It's not as though random_get_entropy_fallback() is super high precision
or guaranteed to be entropic, but basically anything that's not zero all
the time is better than returning zero all the time.
Finally, since random_get_entropy_fallback() is used during extremely
early boot when randomizing freelists in mm_init(), it can be called
before timekeeping has been initialized. In that case there really is
nothing we can do; jiffies hasn't even started ticking yet. So just give
up and return 0.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c54bc0fc84214b203f7a0ebfd1bd308ce2abe920 upstream.
When the timer base is empty, base::next_expiry is set to base::clk +
NEXT_TIMER_MAX_DELTA and base::next_expiry_recalc is false. When no timer
is queued until jiffies reaches base::next_expiry value, the warning for
not finding any expired timer and base::next_expiry_recalc is false in
__run_timers() triggers.
To prevent triggering the warning in this valid scenario
base::timers_pending needs to be added to the warning condition.
Fixes: 31cd0e119d50 ("timers: Recalculate next timer interrupt only when necessary")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20220405191732.7438-3-anna-maria@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e97e42961f8c6cc7bd5fe67cc18417e02d78f1 upstream.
While running some testing on code that happened to allow the variable
tick_nohz_full_running to get set but with no "possible" NOHZ cores to
back up that setting, this warning triggered:
if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE))
WARN_ON(tick_nohz_full_running);
The console was overwhemled with an endless stream of one WARN per tick
per core and there was no way to even see what was going on w/o using a
serial console to capture it and then trace it back to this.
Change it to WARN_ON_ONCE().
Fixes: 08ae95f4fd3b ("nohz_full: Allow the boot CPU to be nohz_full")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211206145950.10927-3-paul.gortmaker@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c86ff8c55b8ae68837b2fa59dc0c203907e9a15f ]
Since commit db3a34e17433 ("clocksource: Retry clock read if long delays
detected") and commit 2e27e793e280 ("clocksource: Reduce clocksource-skew
threshold"), it is found that tsc clocksource fallback to hpet can
sometimes happen on both Intel and AMD systems especially when they are
running stressful benchmarking workloads. Of the 23 systems tested with
a v5.14 kernel, 10 of them have switched to hpet clock source during
the test run.
The result of falling back to hpet is a drastic reduction of performance
when running benchmarks. For example, the fio performance tests can
drop up to 70% whereas the iperf3 performance can drop up to 80%.
4 hpet fallbacks happened during bootup. They were:
[ 8.749399] clocksource: timekeeping watchdog on CPU13: hpet read-back delay of 263750ns, attempt 4, marking unstable
[ 12.044610] clocksource: timekeeping watchdog on CPU19: hpet read-back delay of 186166ns, attempt 4, marking unstable
[ 17.336941] clocksource: timekeeping watchdog on CPU28: hpet read-back delay of 182291ns, attempt 4, marking unstable
[ 17.518565] clocksource: timekeeping watchdog on CPU34: hpet read-back delay of 252196ns, attempt 4, marking unstable
Other fallbacks happen when the systems were running stressful
benchmarks. For example:
[ 2685.867873] clocksource: timekeeping watchdog on CPU117: hpet read-back delay of 57269ns, attempt 4, marking unstable
[46215.471228] clocksource: timekeeping watchdog on CPU8: hpet read-back delay of 61460ns, attempt 4, marking unstable
Commit 2e27e793e280 ("clocksource: Reduce clocksource-skew threshold"),
changed the skew margin from 100us to 50us. I think this is too small
and can easily be exceeded when running some stressful workloads on a
thermally stressed system. So it is switched back to 100us.
Even a maximum skew margin of 100us may be too small in for some systems
when booting up especially if those systems are under thermal stress. To
eliminate the case that the large skew is due to the system being too
busy slowing down the reading of both the watchdog and the clocksource,
an extra consecutive read of watchdog clock is being done to check this.
The consecutive watchdog read delay is compared against
WATCHDOG_MAX_SKEW/2. If the delay exceeds the limit, we assume that
the system is just too busy. A warning will be printed to the console
and the clock skew check is skipped for this round.
Fixes: db3a34e17433 ("clocksource: Retry clock read if long delays detected")
Fixes: 2e27e793e280 ("clocksource: Reduce clocksource-skew threshold")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e27e793e280ff12cb5c202a1214c08b0d3a0f26 ]
Currently, WATCHDOG_THRESHOLD is set to detect a 62.5-millisecond skew in
a 500-millisecond WATCHDOG_INTERVAL. This requires that clocks be skewed
by more than 12.5% in order to be marked unstable. Except that a clock
that is skewed by that much is probably destroying unsuspecting software
right and left. And given that there are now checks for false-positive
skews due to delays between reading the two clocks, it should be possible
to greatly decrease WATCHDOG_THRESHOLD, at least for fine-grained clocks
such as TSC.
Therefore, add a new uncertainty_margin field to the clocksource structure
that contains the maximum uncertainty in nanoseconds for the corresponding
clock. This field may be initialized manually, as it is for
clocksource_tsc_early and clocksource_jiffies, which is copied to
refined_jiffies. If the field is not initialized manually, it will be
computed at clock-registry time as the period of the clock in question
based on the scale and freq parameters to __clocksource_update_freq_scale()
function. If either of those two parameters are zero, the
tens-of-milliseconds WATCHDOG_THRESHOLD is used as a cowardly alternative
to dividing by zero. No matter how the uncertainty_margin field is
calculated, it is bounded below by twice WATCHDOG_MAX_SKEW, that is, by 100
microseconds.
Note that manually initialized uncertainty_margin fields are not adjusted,
but there is a WARN_ON_ONCE() that triggers if any such field is less than
twice WATCHDOG_MAX_SKEW. This WARN_ON_ONCE() is intended to discourage
production use of the one-nanosecond uncertainty_margin values that are
used to test the clock-skew code itself.
The actual clock-skew check uses the sum of the uncertainty_margin fields
of the two clocksource structures being compared. Integer overflow is
avoided because the largest computed value of the uncertainty_margin
fields is one billion (10^9), and double that value fits into an
unsigned int. However, if someone manually specifies (say) UINT_MAX,
they will get what they deserve.
Note that the refined_jiffies uncertainty_margin field is initialized to
TICK_NSEC, which means that skew checks involving this clocksource will
be sufficently forgiving. In a similar vein, the clocksource_tsc_early
uncertainty_margin field is initialized to 32*NSEC_PER_MSEC, which
replicates the current behavior and allows custom setting if needed
in order to address the rare skews detected for this clocksource in
current mainline.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-4-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e8c11b6b3f0b6a283e898344f154641eda94266 upstream.
Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
int main(void)
{
struct timespec time;
clock_gettime(CLOCK_MONOTONIC, &time);
time.tv_nsec = 0;
clock_settime(CLOCK_REALTIME, &time);
return 0;
}
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -9, .tv_nsec = -900000000 }
That makes timespec64_compare() claim that wall_to_monotonic < ts_delta,
but actually the result should be wall_to_monotonic > ts_delta.
After normalization, the result of timespec64_compare() is correct because
the tv_sec comparison is not longer misleading:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -10, .tv_nsec = 100000000 }
Use timespec64_sub() to ensure that ts_delta is normalized, which fixes the
issue.
Fixes: e1d7ba873555 ("time: Always make sure wall_to_monotonic isn't positive")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211213135727.1656662-1-liaoyu15@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7752caeaa70bd31d1714af566c9809688544af upstream.
copy_process currently copies task_struct.posix_cputimers_work as-is. If a
timer interrupt arrives while handling clone and before dup_task_struct
completes then the child task will have:
1. posix_cputimers_work.scheduled = true
2. posix_cputimers_work.work queued.
copy_process clears task_struct.task_works, so (2) will have no effect and
posix_cpu_timers_work will never run (not to mention it doesn't make sense
for two tasks to share a common linked list).
Since posix_cpu_timers_work never runs, posix_cputimers_work.scheduled is
never cleared. Since scheduled is set, future timer interrupts will skip
scheduling work, with the ultimate result that the task will never receive
timer expirations.
Together, the complete flow is:
1. Task 1 calls clone(), enters kernel.
2. Timer interrupt fires, schedules task work on Task 1.
2a. task_struct.posix_cputimers_work.scheduled = true
2b. task_struct.posix_cputimers_work.work added to
task_struct.task_works.
3. dup_task_struct() copies Task 1 to Task 2.
4. copy_process() clears task_struct.task_works for Task 2.
5. Future timer interrupts on Task 2 see
task_struct.posix_cputimers_work.scheduled = true and skip scheduling
work.
Fix this by explicitly clearing contents of task_struct.posix_cputimers_work
in copy_process(). This was never meant to be shared or inherited across
tasks in the first place.
Fixes: 1fb497dd0030 ("posix-cpu-timers: Provide mechanisms to defer timer handling to task_work")
Reported-by: Rhys Hiltner <rhys@justin.tv>
Signed-off-by: Michael Pratt <mpratt@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211101210615.716522-1-mpratt@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 13ccaef77ee86047033c50bf59cb19e0dda3aa97 which is
commit 406dd42bd1ba0c01babf9cde169bb319e52f6147 upstream.
It is reported to cause regressions. A proposed fix has been posted,
but it is not in a released kernel yet. So just revert this from the
stable release so that the bug is fixed. If it's really needed we can
add it back in in a future release.
Link: https://lore.kernel.org/r/87ilz1pwaq.fsf@wylie.me.uk
Reported-by: "Alan J. Wylie" <alan@wylie.me.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c3b5e6ec0fee18bc2ce38d1dfe913413205f908 ]
If high resolution timers are disabled the timerfd notification about a
clock was set event is not happening for all cases which use
clock_was_set_delayed() because that's a NOP for HIGHRES=n, which is wrong.
Make clock_was_set_delayed() unconditially available to fix that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.196661266@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627ef5ae2df8eeccb20d5af0e4cfa4df9e61ed28 ]
If __hrtimer_start_range_ns() is invoked with an already armed hrtimer then
the timer has to be canceled first and then added back. If the timer is the
first expiring timer then on removal the clockevent device is reprogrammed
to the next expiring timer to avoid that the pending expiry fires needlessly.
If the new expiry time ends up to be the first expiry again then the clock
event device has to reprogrammed again.
Avoid this by checking whether the timer is the first to expire and in that
case, keep the timer on the current CPU and delay the reprogramming up to
the point where the timer has been enqueued again.
Reported-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135157.873137732@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 406dd42bd1ba0c01babf9cde169bb319e52f6147 ]
When an itimer deactivates a previously armed expiration, it simply doesn't
do anything. As a result the process wide cputime counter keeps running and
the tick dependency stays set until it reaches the old ghost expiration
value.
This can be reproduced with the following snippet:
void trigger_process_counter(void)
{
struct itimerval n = {};
n.it_value.tv_sec = 100;
setitimer(ITIMER_VIRTUAL, &n, NULL);
n.it_value.tv_sec = 0;
setitimer(ITIMER_VIRTUAL, &n, NULL);
}
Fix this with resetting the relevant base expiration. This is similar to
disarming a timer.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-4-frederic@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bb7262b295472eb6858b5c49893954794027cd84 upstream.
syzbot reported KCSAN data races vs. timer_base::timer_running being set to
NULL without holding base::lock in expire_timers().
This looks innocent and most reads are clearly not problematic, but
Frederic identified an issue which is:
int data = 0;
void timer_func(struct timer_list *t)
{
data = 1;
}
CPU 0 CPU 1
------------------------------ --------------------------
base = lock_timer_base(timer, &flags); raw_spin_unlock(&base->lock);
if (base->running_timer != timer) call_timer_fn(timer, fn, baseclk);
ret = detach_if_pending(timer, base, true); base->running_timer = NULL;
raw_spin_unlock_irqrestore(&base->lock, flags); raw_spin_lock(&base->lock);
x = data;
If the timer has previously executed on CPU 1 and then CPU 0 can observe
base->running_timer == NULL and returns, assuming the timer has completed,
but it's not guaranteed on all architectures. The comment for
del_timer_sync() makes that guarantee. Moving the assignment under
base->lock prevents this.
For non-RT kernel it's performance wise completely irrelevant whether the
store happens before or after taking the lock. For an RT kernel moving the
store under the lock requires an extra unlock/lock pair in the case that
there is a waiter for the timer, but that's not the end of the world.
Reported-by: syzbot+aa7c2385d46c5eba0b89@syzkaller.appspotmail.com
Reported-by: syzbot+abea4558531bae1ba9fe@syzkaller.appspotmail.com
Fixes: 030dcdd197d7 ("timers: Prepare support for PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/87lfea7gw8.fsf@nanos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3402d93c73bf6bb4df6d7c2aac35abfc3c50e2 upstream.
Since the process wide cputime counter is started locklessly from
posix_cpu_timer_rearm(), it can be concurrently stopped by operations
on other timers from the same thread group, such as in the following
unlucky scenario:
CPU 0 CPU 1
----- -----
timer_settime(TIMER B)
posix_cpu_timer_rearm(TIMER A)
cpu_clock_sample_group()
(pct->timers_active already true)
handle_posix_cpu_timers()
check_process_timers()
stop_process_timers()
pct->timers_active = false
arm_timer(TIMER A)
tick -> run_posix_cpu_timers()
// sees !pct->timers_active, ignore
// our TIMER A
Fix this with simply locking process wide cputime counting start and
timer arm in the same block.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Fixes: 60f2ceaa8111 ("posix-cpu-timers: Remove unnecessary locking around cpu_clock_sample_group")
Cc: stable@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aebacb7f6ca1926918734faae14d1f0b6fae5cb7 ]
31cd0e119d50 ("timers: Recalculate next timer interrupt only when
necessary") subtly altered get_next_timer_interrupt()'s behaviour. The
function no longer consistently returns KTIME_MAX with no timers
pending.
In order to decide if there are any timers pending we check whether the
next expiry will happen NEXT_TIMER_MAX_DELTA jiffies from now.
Unfortunately, the next expiry time and the timer base clock are no
longer updated in unison. The former changes upon certain timer
operations (enqueue, expire, detach), whereas the latter keeps track of
jiffies as they move forward. Ultimately breaking the logic above.
A simplified example:
- Upon entering get_next_timer_interrupt() with:
jiffies = 1
base->clk = 0;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry == base->clk + NEXT_TIMER_MAX_DELTA', the function
returns KTIME_MAX.
- 'base->clk' is updated to the jiffies value.
- The next time we enter get_next_timer_interrupt(), taking into account
no timer operations happened:
base->clk = 1;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry != base->clk + NEXT_TIMER_MAX_DELTA', the function
returns a valid expire time, which is incorrect.
This ultimately might unnecessarily rearm sched's timer on nohz_full
setups, and add latency to the system[1].
So, introduce 'base->timers_pending'[2], update it every time
'base->next_expiry' changes, and use it in get_next_timer_interrupt().
[1] See tick_nohz_stop_tick().
[2] A quick pahole check on x86_64 and arm64 shows it doesn't make
'struct timer_base' any bigger.
Fixes: 31cd0e119d50 ("timers: Recalculate next timer interrupt only when necessary")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7560c02bdffb7c52d1457fa551b9e745d4b9e754 ]
Some sorts of per-CPU clock sources have a history of going out of
synchronization with each other. However, this problem has purportedy been
solved in the past ten years. Except that it is all too possible that the
problem has instead simply been made less likely, which might mean that
some of the occasional "Marking clocksource 'tsc' as unstable" messages
might be due to desynchronization. How would anyone know?
Therefore apply CPU-to-CPU synchronization checking to newly unstable
clocksource that are marked with the new CLOCK_SOURCE_VERIFY_PERCPU flag.
Lists of desynchronized CPUs are printed, with the caveat that if it
is the reporting CPU that is itself desynchronized, it will appear that
all the other clocks are wrong. Just like in real life.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-2-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db3a34e17433de2390eb80d436970edcebd0ca3e ]
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2d036dfa5f10df9782f5278fc591d79d283c1fad upstream.
The return value on success (>= 0) is overwritten by the return value of
put_old_timex32(). That works correct in the fault case, but is wrong for
the success case where put_old_timex32() returns 0.
Just check the return value of put_old_timex32() and return -EFAULT in case
it is not zero.
[ tglx: Massage changelog ]
Fixes: 3a4d44b61625 ("ntp: Move adjtimex related compat syscalls to native counterparts")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210414030449.90692-1-chenjun102@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5abbe51a526253b9f003e9a0a195638dc882d660 upstream.
Preparation for fixing get_nr_restart_syscall() on X86 for COMPAT.
Add a new helper which sets restart_block->fn and calls a dummy
arch_set_restart_data() helper.
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174641.GA17871@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 46eb1701c046cc18c032fa68f3c8ccbf24483ee4 ]
hrtimer_force_reprogram() and hrtimer_interrupt() invokes
__hrtimer_get_next_event() to find the earliest expiry time of hrtimer
bases. __hrtimer_get_next_event() does not update
cpu_base::[softirq_]_expires_next to preserve reprogramming logic. That
needs to be done at the callsites.
hrtimer_force_reprogram() updates cpu_base::softirq_expires_next only when
the first expiring timer is a softirq timer and the soft interrupt is not
activated. That's wrong because cpu_base::softirq_expires_next is left
stale when the first expiring timer of all bases is a timer which expires
in hard interrupt context. hrtimer_interrupt() does never update
cpu_base::softirq_expires_next which is wrong too.
That becomes a problem when clock_settime() sets CLOCK_REALTIME forward and
the first soft expiring timer is in the CLOCK_REALTIME_SOFT base. Setting
CLOCK_REALTIME forward moves the clock MONOTONIC based expiry time of that
timer before the stale cpu_base::softirq_expires_next.
cpu_base::softirq_expires_next is cached to make the check for raising the
soft interrupt fast. In the above case the soft interrupt won't be raised
until clock monotonic reaches the stale cpu_base::softirq_expires_next
value. That's incorrect, but what's worse it that if the softirq timer
becomes the first expiring timer of all clock bases after the hard expiry
timer has been handled the reprogramming of the clockevent from
hrtimer_interrupt() will result in an interrupt storm. That happens because
the reprogramming does not use cpu_base::softirq_expires_next, it uses
__hrtimer_get_next_event() which returns the actual expiry time. Once clock
MONOTONIC reaches cpu_base::softirq_expires_next the soft interrupt is
raised and the storm subsides.
Change the logic in hrtimer_force_reprogram() to evaluate the soft and hard
bases seperately, update softirq_expires_next and handle the case when a
soft expiring timer is the first of all bases by comparing the expiry times
and updating the required cpu base fields. Split this functionality into a
separate function to be able to use it in hrtimer_interrupt() as well
without copy paste.
Fixes: 5da70160462e ("hrtimer: Implement support for softirq based hrtimers")
Reported-by: Mikael Beckius <mikael.beckius@windriver.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikael Beckius <mikael.beckius@windriver.com>
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210223160240.27518-1-anna-maria@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8ea8e7dd6e1662e34e730eadfc52aa6816f9dd ]
can_stop_idle_tick() checks whether the do_timer() duty has been taken over
by a CPU on boot. That's silly because the boot CPU always takes over with
the initial clockevent device.
But even if no CPU would have installed a clockevent and taken over the
duty then the question whether the tick on the current CPU can be stopped
or not is moot. In that case the current CPU would have no clockevent
either, so there would be nothing to keep ticking.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20201206212002.725238293@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
UBSAN reports:
Undefined behaviour in ./include/linux/time64.h:127:27
signed integer overflow:
17179869187 * 1000000000 cannot be represented in type 'long long int'
Call Trace:
timespec64_to_ns include/linux/time64.h:127 [inline]
set_cpu_itimer+0x65c/0x880 kernel/time/itimer.c:180
do_setitimer+0x8e/0x740 kernel/time/itimer.c:245
__x64_sys_setitimer+0x14c/0x2c0 kernel/time/itimer.c:336
do_syscall_64+0xa1/0x540 arch/x86/entry/common.c:295
Commit bd40a175769d ("y2038: itimer: change implementation to timespec64")
replaced the original conversion which handled time clamping correctly with
timespec64_to_ns() which has no overflow protection.
Fix it in timespec64_to_ns() as this is not necessarily limited to the
usage in itimers.
[ tglx: Added comment and adjusted the fixes tag ]
Fixes: 361a3bf00582 ("time64: Add time64.h header and define struct timespec64")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1598952616-6416-1-git-send-email-prime.zeng@hisilicon.com
Since sched_clock_read_begin() and sched_clock_read_retry() are called
by notrace function sched_clock(), they shouldn't be traceable either,
or else ftrace_graph_caller will run into a dead loop on the path
as below (arm for instance):
ftrace_graph_caller()
prepare_ftrace_return()
function_graph_enter()
ftrace_push_return_trace()
trace_clock_local()
sched_clock()
sched_clock_read_begin/retry()
Fixes: 1b86abc1c645 ("sched_clock: Expose struct clock_read_data")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200929082027.16787-1-quanyang.wang@windriver.com
With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.
This patch restores the spirit of commit f227e3ec3b5c ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.
The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output. An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.
It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack. Oops.
This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key. (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.) Speed is prioritized over security;
attacks are rare, while performance is always wanted.
Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution. This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec3b5c; moved SIPROUND definitions
to prandom.h for later use; merged George's prandom_seed() proposal;
inlined siprand_u32(); replaced the net_rand_state[] array with 4
members to fix a build issue; cosmetic cleanups to make checkpatch
happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Pull RCU changes from Ingo Molnar:
- Debugging for smp_call_function()
- RT raw/non-raw lock ordering fixes
- Strict grace periods for KASAN
- New smp_call_function() torture test
- Torture-test updates
- Documentation updates
- Miscellaneous fixes
[ This doesn't actually pull the tag - I've dropped the last merge from
the RCU branch due to questions about the series. - Linus ]
* tag 'core-rcu-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
smp: Make symbol 'csd_bug_count' static
kernel/smp: Provide CSD lock timeout diagnostics
smp: Add source and destination CPUs to __call_single_data
rcu: Shrink each possible cpu krcp
rcu/segcblist: Prevent useless GP start if no CBs to accelerate
torture: Add gdb support
rcutorture: Allow pointer leaks to test diagnostic code
rcutorture: Hoist OOM registry up one level
refperf: Avoid null pointer dereference when buf fails to allocate
rcutorture: Properly synchronize with OOM notifier
rcutorture: Properly set rcu_fwds for OOM handling
torture: Add kvm.sh --help and update help message
rcutorture: Add CONFIG_PROVE_RCU_LIST to TREE05
torture: Update initrd documentation
rcutorture: Replace HTTP links with HTTPS ones
locktorture: Make function torture_percpu_rwsem_init() static
torture: document --allcpus argument added to the kvm.sh script
rcutorture: Output number of elapsed grace periods
rcutorture: Remove KCSAN stubs
rcu: Remove unused "cpu" parameter from rcu_report_qs_rdp()
...
- Add deadlock detection for recursive read-locks. The rationale is outlined
in:
224ec489d3cd: ("lockdep/Documention: Recursive read lock detection reasoning")
The main deadlock pattern we want to detect is:
TASK A: TASK B:
read_lock(X);
write_lock(X);
read_lock_2(X);
- Add "latch sequence counters" (seqcount_latch_t):
A sequence counter variant where the counter even/odd value is used to
switch between two copies of protected data. This allows the read path,
typically NMIs, to safely interrupt the write side critical section.
We utilize this new variant for sched-clock, and to make x86 TSC handling safer.
- Other seqlock cleanups, fixes and enhancements
- KCSAN updates
- LKMM updates
- Misc updates, cleanups and fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Iq51
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"These are the locking updates for v5.10:
- Add deadlock detection for recursive read-locks.
The rationale is outlined in commit 224ec489d3cd ("lockdep/
Documention: Recursive read lock detection reasoning")
The main deadlock pattern we want to detect is:
TASK A: TASK B:
read_lock(X);
write_lock(X);
read_lock_2(X);
- Add "latch sequence counters" (seqcount_latch_t):
A sequence counter variant where the counter even/odd value is used
to switch between two copies of protected data. This allows the
read path, typically NMIs, to safely interrupt the write side
critical section.
We utilize this new variant for sched-clock, and to make x86 TSC
handling safer.
- Other seqlock cleanups, fixes and enhancements
- KCSAN updates
- LKMM updates
- Misc updates, cleanups and fixes"
* tag 'locking-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
lockdep: Revert "lockdep: Use raw_cpu_*() for per-cpu variables"
lockdep: Fix lockdep recursion
lockdep: Fix usage_traceoverflow
locking/atomics: Check atomic-arch-fallback.h too
locking/seqlock: Tweak DEFINE_SEQLOCK() kernel doc
lockdep: Optimize the memory usage of circular queue
seqlock: Unbreak lockdep
seqlock: PREEMPT_RT: Do not starve seqlock_t writers
seqlock: seqcount_LOCKNAME_t: Introduce PREEMPT_RT support
seqlock: seqcount_t: Implement all read APIs as statement expressions
seqlock: Use unique prefix for seqcount_t property accessors
seqlock: seqcount_LOCKNAME_t: Standardize naming convention
seqlock: seqcount latch APIs: Only allow seqcount_latch_t
rbtree_latch: Use seqcount_latch_t
x86/tsc: Use seqcount_latch_t
timekeeping: Use seqcount_latch_t
time/sched_clock: Use seqcount_latch_t
seqlock: Introduce seqcount_latch_t
mm/swap: Do not abuse the seqcount_t latching API
time/sched_clock: Use raw_read_seqcount_latch() during suspend
...
Core:
- Early boot support for the NMI safe timekeeper by utilizing
local_clock() up to the point where timekeeping is initialized. This
allows printk() to store multiple timestamps in the ringbuffer which is
useful for coordinating dmesg information across a fleet of machines.
- Provide a multi-timestamp accessor for printk()
- Make timer init more robust by checking for invalid timer flags.
- Comma vs. semicolon fixes
Drivers:
- Support for new platforms in existing drivers (SP804 and Renesas CMT)
- Comma vs. semicolon fixes
-----BEGIN PGP SIGNATURE-----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=h6YX
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping updates from Thomas Gleixner:
"Updates for timekeeping, timers and related drivers:
Core:
- Early boot support for the NMI safe timekeeper by utilizing
local_clock() up to the point where timekeeping is initialized.
This allows printk() to store multiple timestamps in the ringbuffer
which is useful for coordinating dmesg information across a fleet
of machines.
- Provide a multi-timestamp accessor for printk()
- Make timer init more robust by checking for invalid timer flags.
- Comma vs semicolon fixes
Drivers:
- Support for new platforms in existing drivers (SP804 and Renesas
CMT)
- Comma vs semicolon fixes
* tag 'timers-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/armada-370-xp: Use semicolons rather than commas to separate statements
clocksource/drivers/mps2-timer: Use semicolons rather than commas to separate statements
timers: Mask invalid flags in do_init_timer()
clocksource/drivers/sp804: Enable Hisilicon sp804 timer 64bit mode
clocksource/drivers/sp804: Add support for Hisilicon sp804 timer
clocksource/drivers/sp804: Support non-standard register offset
clocksource/drivers/sp804: Prepare for support non-standard register offset
clocksource/drivers/sp804: Remove a mismatched comment
clocksource/drivers/sp804: Delete the leading "__" of some functions
clocksource/drivers/sp804: Remove unused sp804_timer_disable() and timer-sp804.h
clocksource/drivers/sp804: Cleanup clk_get_sys()
dt-bindings: timer: renesas,cmt: Document r8a774e1 CMT support
dt-bindings: timer: renesas,cmt: Document r8a7742 CMT support
alarmtimer: Convert comma to semicolon
timekeeping: Provide multi-timestamp accessor to NMI safe timekeeper
timekeeping: Utilize local_clock() for NMI safe timekeeper during early boot
