IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 624407d2cf14ff58e53bf4b2af9595c4f21d606e upstream.
The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LOS signal on SFP pin 8 behaves:
bit 2 - Loss of Signal implemented, signal inverted from standard
definition in SFP MSA (often called "Signal Detect").
bit 1 - Loss of Signal implemented, signal as defined in SFP MSA
(often called "Rx_LOS").
Clearly, setting both bits results in a meaningless situation: it would
mean that LOS is implemented in both the normal sense (1 = signal loss)
and inverted sense (0 = signal loss).
Unfortunately, there are modules out there which set both bits, which
will be initially interpret as "inverted" sense, and then, if the LOS
signal changes state, we will toggle between LINK_UP and WAIT_LOS
states.
Change our LOS handling to give well defined behaviour: only interpret
these bits as meaningful if exactly one is set, otherwise treat it as
if LOS is not implemented.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a77233ec6d114322e2c4f71b4e26dbecd9ea8a7 upstream.
Do not check the encoding when deriving 1000BASE-X from the bitrate
when no other modes are discovered. Some GPON modules (VSOL V2801F
and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a
1200Mbaud bitrate, but should be driven with 1000BASE-X on the host
side.
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c056d480b40a68f2520ccc156c7fae672d69d57d ]
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dda2 ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1dd9bf688b0dcc5a34dca660de46c7570bd9243 ]
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that.
Fixes: 733336262b28 ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 133bf7b4fbbe58cff5492e37e95e75c88161f1b8 ]
Avoid a forward declaration by moving the callers of
bcm54xx_config_clock_delay() below its body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4217a64e18a1647a0dbc68cb3169a5a06f054ec8 ]
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d82c6c1aaccd2877b6082cebcb1746a13648a16d ]
if pl->mac_ops->mac_finish() failed, phylink_err should use
"mac_finish" instead of "mac_prepare".
Fixes: b7ad14c2fe2d4 ("net: phylink: re-implement interface configuration with PCS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a1468ba0e02eee24ae1353e8933793a27198e20 ]
Per the datasheet, when we clear the power down bit, the PHY remains in
an internal reset state for 40us and then resume normal operation.
Account for that delay to avoid any issues in the future if
genphy_resume() changes.
Fixes: fe26821fa614 ("net: phy: broadcom: Wire suspend/resume for BCM54810")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764d31cacfe48440745c4bbb55a62ac9471c9f19 ]
Following a similar reinstate for the KSZ9031.
Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.
Bluntly removing that default may expose a lot of situations where various
PHYs/board implementations won't recover on various changes.
Like with this implementation during a 4.9.x to 5.4.x LTS transition.
I think it's a good thing to remove unwanted soft resets but wonder if it
did open a can of worms?
Atleast this fixes one iMX6 FEC/RMII/8081 combo.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224205536.9349-1-christian.melki@t2data.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7f654157f0aefba04cd7f6297351c87b76b47b89 upstream.
When CONFIG_PM_SLEEP is disabled, the compiler warns about unused
functions:
drivers/net/phy/phy_device.c:273:12: error: unused function 'mdio_bus_phy_suspend' [-Werror,-Wunused-function]
static int mdio_bus_phy_suspend(struct device *dev)
drivers/net/phy/phy_device.c:293:12: error: unused function 'mdio_bus_phy_resume' [-Werror,-Wunused-function]
static int mdio_bus_phy_resume(struct device *dev)
The logic is intentional, so just mark these two as __maybe_unused
and remove the incorrect #ifdef.
Fixes: 4c0d2e96ba05 ("net: phy: consider that suspend2ram may cut off PHY power")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210225145748.404410-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9032dba5a2b2bbf0fdce67c8795300ec9923b43 upstream.
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 426c6cbc409cbda9ab1a9dbf15d3c2ef947eb8c1 ]
The workaround for VSOL V2801F brand based GPON SFP modules added in commit
0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0
workaround") works only for IDs added explicitly to the list. Since there
are rebranded modules where OEM vendors put different strings into the
vendor name field, we cannot base workaround on IDs only.
Moreover the issue which the above mentioned commit tried to work around is
generic not only to VSOL based modules, but rather to all GPON modules
based on Realtek RTL8672 and RTL9601C chips.
These include at least the following GPON modules:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
These Realtek chips have broken EEPROM emulator which for N-byte read
operation returns just the first byte of EEPROM data, followed by N-1
zeros.
Introduce a new function, sfp_id_needs_byte_io(), which detects SFP modules
with broken EEPROM emulator based on N-1 zeros and switch to 1 byte EEPROM
reading operation.
Function sfp_i2c_read() now always uses single byte reading when it is
required and when function sfp_hwmon_probe() detects single byte access,
it disables registration of hwmon device, because in this case we cannot
reliably and atomically read 2 bytes as is required by the standard for
retrieving values from diagnostic area.
(These Realtek chips are broken in a way that violates SFP standards for
diagnostic interface. Kernel in this case simply cannot do anything less
of skipping registration of the hwmon interface.)
This patch fixes reading of EEPROM content from SFP modules based on
Realtek RTL8672 and RTL9601C chips. Diagnostic interface of EEPROM stays
broken and cannot be fixed.
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Co-developed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d035bed2a4a6c4878518749348be61bf082d12a ]
Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.
Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.
Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b4f847673299577c29b71d3f3acd3c313d81b7 ]
The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information
stored in its EEPROM. It claims to support all transceiver types including
10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is
the only one supported.
This module has also phys_id set to SFF, and the SFP subsystem currently
does not allow to use SFP modules detected as SFFs. Add exception for this
module so it can be detected as supported.
This change finally allows to detect and use SFP GPON module Ubiquiti
U-Fiber Instant on Linux system.
EEPROM content of this SFP module is (where XX is serial number):
00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.??
10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT
20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA
30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6
40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX
50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cc2c646be0b22037f31c958e96c0544a073d108 ]
At Power-On Reset, transients may cause the LCPLL to lock onto a
clock that is momentarily unstable. This is normally seen in QSGMII
setups where the higher speed 6G SerDes is being used.
This patch adds an initial LCPLL Reset to the PHY (first instance)
to avoid this issue.
Fixes: e4f9ba642f0b ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c0d2e96ba055bd8911bb8287def4f8ebbad15b6 ]
Claudiu reported that on his system S2R cuts off power to the PHY and
after resuming certain PHY settings are lost. The PM folks confirmed
that cutting off power to selected components in S2R is a valid case.
Therefore resuming from S2R, same as from hibernation, has to assume
that the PHY has power-on defaults. As a consequence use the restore
callback also as resume callback.
In addition make sure that the interrupt configuration is restored.
Let's do this in phy_init_hw() and ensure that after this call
actual interrupt configuration is in sync with phydev->interrupts.
Currently, if interrupt was enabled before hibernation, we would
resume with interrupt disabled because that's the power-on default.
This fix applies cleanly only after the commit marked as fixed.
I don't have an affected system, therefore change is compile-tested
only.
[0] https://lore.kernel.org/netdev/1610120754-14331-1-git-send-email-claudiu.beznea@microchip.com/
Fixes: 611d779af7ca ("net: phy: fix MDIO bus PM PHY resuming")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18caa97b1bda0a3d126a7be165ddcfc56c2dde6 ]
Commit bedd8d78aba3 ("net: phy: smsc: LAN8710/20: add phy refclk in
support") added the phy clk support. The commit already checks if
clk_get_optional() throw an error but instead of returning the error it
ignores it.
Fixes: bedd8d78aba3 ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210111085932.28680-1-m.felsch@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing clk_disable_unprepare() before return from
smsc_phy_probe() in the error handling case.
Fixes: bedd8d78aba3 ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605180239-1792-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Selecting VSC8575 as a MACSec PHY was not correct
The relevant datasheet can be found here:
- VSC8575: https://www.microchip.com/wwwproducts/en/VSC8575
History:
v1 -> v2:
- Corrected the sha in the "Fixes:" tag
Fixes: 1bbe0ecc2a1a ("net: phy: mscc: macsec initialization")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201113091116.1102450-1-steen.hegelund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8401-internal PHY identifies as RTL8201CP, and the init
sequence in r8169, copied from vendor driver r8168, uses paged
operations. Therefore set the same paged operation callbacks as
for the other Realtek PHY's.
Fixes: cdafdc29ef75 ("r8169: sync support for RTL8401 with vendor driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/69882f7a-ca2f-e0c7-ae83-c9b6937282cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gpiod_to_irq() never return 0, but returns negative in
case of error, check it and set gpio_irq to 0.
Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201031031053.25264-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert m88e1318_get_wol() to use the well implemented phy_read_paged()
instead of open coding it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the comparisons of u16 integers value and sopass_val with
less than zero for error checking is always false because the values
are unsigned. Fix this by making these variables int. This does not
affect the shift and mask operations performed on these variables
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: 49fc23018ec6 ("net: phy: dp83869: support Wake on LAN")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek single-chip Ethernet PHY solutions can be separated as below:
10M/100Mbps: RTL8201X
1Gbps: RTL8211X
2.5Gbps: RTL8226/RTL8221X
RTL8226 is the first version for realtek that compatible 2.5Gbps single PHY.
Since RTL8226 is single port only, realtek changes its name to RTL8221B from
the second version.
PHY ID for RTL8226 is 0x001cc800 and RTL8226B/RTL8221B is 0x001cc840.
RTL8125 is not a single PHY solution, it integrates PHY/MAC/PCIE bus
controller and embedded memory.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the check covers only parts of the contexts in which these
functions cannot be called. It fails to detect preemption or interrupt
disabled invocations.
As the functions which contain these warnings invoke mutex_lock() which
contains a broad variety of checks (always enabled or debug option
dependent) and therefore covers all invalid conditions already, there is no
point in having inconsistent warnings in those drivers. The conditional
return is not really valuable in practice either.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the speed optimization bit on the DP83869 PHY.
Speed optimization, also known as link downshift, enables fallback to 100M
operation after multiple consecutive failed attempts at Gigabit link
establishment. Such a case could occur if cabling with only four wires
(two twisted pairs) were connected instead of the standard cabling with
eight wires (four twisted pairs).
The number of failed link attempts before falling back to 100M operation is
configurable. By default, four failed link attempts are required before
falling back to 100M.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds WoL support on TI DP83869 for magic, magic secure, unicast and
broadcast.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:
ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM72113 features a 28nm integrated EPHY, add an entry to the driver for
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ALDPS(Advanced Link Down Power Saving) to save power when
link down.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the fiber advertisement for speed and duplex modes with the
100base-FX full and half linkmode entries.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to advertise the Fiber connection if the strap or the
op-mode is configured for 100Base-FX.
Auto negotiation is not supported on this PHY when in fiber mode.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal Gigabit PHY on Broadcom STB chips has a digital clock which
drives its MDIO interface among other things, the driver now requests
and manage that clock during .probe() and .remove() accordingly.
Because the PHY driver can be probed with the clocks turned off we need
to apply the dummy BMSR workaround during the driver probe function to
ensure subsequent MDIO read or write towards the PHY will succeed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8814 is a low-power, quad-port triple-speed (10BASE-T/100BASETX/1000BASE-T)
Ethernet physical layer transceiver (PHY). It supports transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded
twisted pair (UTP) cables.
LAN8814 supports industry-standard QSGMII (Quad Serial Gigabit Media
Independent Interface) and Q-USGMII (Quad Universal Serial Gigabit Media
Independent Interface) providing chip-to-chip connection to four Gigabit
Ethernet MACs using a single serialized link (differential pair) in each
direction.
The LAN8814 SKU supports high-accuracy timestamping functions to
support IEEE-1588 solutions using Microchip Ethernet switches, as well as
customer solutions based on SoCs and FPGAs.
The LAN8804 SKU has same features as that of LAN8814 SKU except that it does
not support 1588, SyncE, or Q-USGMII with PCH/MCH.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC.
Signed-off-by: Divya Koppera<divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the micrel phy driver calls phy_init_hw() as a workaround,
the commit 9886a4dbd2aa ("net: phy: call phy_disable_interrupts()
in phy_init_hw()") disables the interrupt unexpectedly. So,
call phy_disable_interrupts() in phy_attach_direct() instead.
Otherwise, the phy cannot link up after the ethernet cable was
disconnected.
Note that other drivers (like at803x.c) also calls phy_init_hw().
So, perhaps, the driver caused a similar issue too.
Fixes: 9886a4dbd2aa ("net: phy: call phy_disable_interrupts() in phy_init_hw()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't reset the phy without respect to the PHY library state machine
because this breaks the phy IRQ mode. The same behaviour can be archived
now by specifying the refclk.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to specify the clock provider for the PHY refclk and don't
rely on 'magic' host clock setup. [1] tried to address this by
introducing a flag and fixing the corresponding host. But this commit
breaks the IRQ support since the irq setup during .config_intr() is
thrown away because the reset comes from the side without respecting the
current PHY state within the PHY library state machine. Furthermore the
commit fixed the problem only for FEC based hosts other hosts acting
like the FEC are not covered.
This commit goes the other way around to address the bug fixed by [1].
Instead of resetting the device from the side every time the refclk gets
(re-)enabled it requests and enables the clock till the device gets
removed. Now the PHY library is the only place where the PHY gets reset
to respect the PHY library state machine.
[1] commit 7f64e5b18ebb ("net: phy: smsc: LAN8710/20: add
PHY_RST_AFTER_CLK_EN flag")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit the driver specific config_init hook early if energy detection is
disabled. We can do this because we don't need to clear the interrupt
status here. Clearing the status should be removed anyway since this is
handled by the phy_enable_interrupts().
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't enable the interrupt if the platform disable the energy detection
by "smsc,disable-energy-detect".
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444a4 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
