IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 8967b27a6c1c19251989c7ab33c058d16e4a5f53 upstream.
Per schematic, both PU and SOC regulator are supplied from LTC3676 SW1
via VDDSOC_IN rail, add the PU input. Both VDD1P1, VDD2P5 are supplied
from LTC3676 SW2 via VDDHIGH_IN rail, add both inputs.
While no instability or problems are currently observed, the regulators
should be fully described in DT and that description should fully match
the hardware, else this might lead to unforseen issues later. Fix this.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e4a4a08cd78efcaddbc2e4c5ed86b5a5cb8a15e upstream.
The FEC does not have a PHY so it should not have a phy-handle. It is
connected to the switch at RGMII level so we need a fixed-link sub-node
on both ends.
This was not a problem until the qca8k.c driver was converted to PHYLINK
by commit b3591c2a3661 ("net: dsa: qca8k: Switch to PHYLINK instead of
PHYLIB"). That commit revealed the FEC configuration was not correct.
Fixes: 87489ec3a77f ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e2fa4959c4f44815ce33e46e4054eeb0f346053 ]
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the
correct name of the property is 'fsl,tuning-step'.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fixes: f13f571ac8a1 ("ARM: dts: imx7d-pico: Extend peripherals support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c8f0338cdacc90fdf6468adafa8e27952987f00 ]
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the
correct name of the property is 'fsl,tuning-step'.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fixes: ae7b3384b61b ("ARM: dts: Add support for 96Boards Meerkat96 board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 25de4ce5ed02994aea8bc111d133308f6fd62566 upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ba585cc5b56ea14a453ba6be9bdb984ed33471a ]
UniPhier PXs2 boards have RTL8211E ethernet phy, and the phy have the RX/TX
delays of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
After the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: e3cc931921d2 ("ARM: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5d46a1adafafce2b0c9105eab563709c84e3db ]
The si7021 was incorrectly placed at 0x20 on i2c bus 7. It is at 0x40.
Fixes: 9c44db7096e0 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1429f3d3029b65cd4032f6218d5290911377ce4 ]
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a757 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da926e813fc7f9f0912fa413981a1f5ba63a536d ]
After set PROBE_PREFER_ASYNCHRONOUS flag on the mmc host drivers,
the order of /dev/mmcblkN was not fixed in some SoCs which have
multiple SDHI and/or MMCIF controllers. So, we were hard to use
such a device as rootfs by using the kernel parameter like
"root=/dev/mmcblkNpM".
According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into R-Car Gen2
board dts files. Note that, since R-Car Gen2 is even more complicated
about SDHI and/or MMCIF channels variations and they share pins,
add the aliases into board dts files instead of SoC dtsi files.
[1]
https://lore.kernel.org/linux-arm-kernel/CAPDyKFptyEQNJu8cqzMt2WRFZcwEdjDiytMBp96nkoZyprTgmA@mail.gmail.com/
Fixes: 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1613131316-30994-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 214e6ec8c9f5a3353d3282b3ff475d3ee86cc21a ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 99bb20321f0e ("ARM: dts: s5pv210: Correct fuelgauge definition on Aries")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-10-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8987efbb17c2522be8615085df9a14da2ab53d34 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: c61248afa819 ("ARM: dts: Add max77686 RTC interrupt to cros5250-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6368c60561370e4a92fac22982a3bd656172170 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94c2 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6503c568e97a52f8b7a3109718db438e52e59485 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: eea6653aae7b ("ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52dcd6e70fab51f53292e53336ecb007bb60889 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 15dfdfad2d4a ("ARM: dts: Add basic dts for Exynos4412-based Trats 2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15107e443ab8c6cb35eff10438993e4bc944d9ae ]
The Maxim MUIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 7eec1266751b ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a45f33bd36efbb624198cfa9fdf1f66fd1c3d26 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: e8614292cd41 ("ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46799802136670e00498f19898f1635fbc85f583 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca7a049ad1a72ec5f03d1330b53575237fcb727c ]
Having a button code and not a key code causes issues with libinput.
udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug
within libinput.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210402130227.21478-1-nicolas.ferre@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeceecd40d94ed3c00bfe1cfe59dd1bfac2fc6fe ]
The TVK1281618 R3 sensors are different from the R2 board,
some incorrectness is fixed and some new sensors added, we
also rename the nodes appropriately with accelerometer@
etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27b9689e1f3278919c6183c565d837d0aef6fc1 ]
Rename avdd supply to vdda of the touchscreen node. The old supply name
was incorrect.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4e792d1acce31c2eb7b9193ab06ab94de05bf42 upstream.
The LLVM ld.lld linker uses a different symbol type for __bss_start,
resulting in the calculation of KBSS_SZ to be thrown off. Up until now,
this has gone unnoticed as it only affects the appended DTB case, but
pending changes for ARM in the way the decompressed kernel is cleaned
from the caches has uncovered this problem.
On a ld.lld build:
$ nm vmlinux |grep bss_
c1c22034 D __bss_start
c1c86e98 B __bss_stop
resulting in
$ readelf -s arch/arm/boot/compressed/vmlinux | grep bss_size
433: c1c86e98 0 NOTYPE GLOBAL DEFAULT ABS _kernel_bss_size
which is obviously incorrect, and may cause the cache clean to access
unmapped memory, or cause the size calculation to wrap, resulting in no
cache clean to be performed at all.
Fix this by updating the sed regex to take D type symbols into account.
Link: https://lore.kernel.org/linux-arm-kernel/6c65bcef-d4e7-25fa-43cf-2c435bb61bb9@collabora.com/
Link: https://lore.kernel.org/linux-arm-kernel/20210205085220.31232-1-ardb@kernel.org/
Cc: <stable@vger.kernel.org> # v4.19+
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1ebdb3741993f853865d1bd8f77881916ad53a7 ]
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77335a040178a0456d4eabc8bf17a7ca3ee4a327 ]
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 140a776833957539c84301dbdb4c3013876de118 ]
We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f57011e72f5fe0421ec7a812beb1b57bdf4bb47f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880d5 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a26c56ae67fa9fbb45a8a232dcd7ebaa7af16086 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bbce32a20d6a72c767a7f85fd6127babd1410ac ]
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa96941 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4817a1b6b77db538bc0141c3b138f2df803ce87 ]
For NAND Ecc layout, there is a dependency from old kernel's nand driver
setting and current. if old kernel use 4 bit ecc , we should use 4 bit
in new kernel either. else will run into following error at filesystem
mounting.
So, enable fsl,use-minimum-ecc from device tree, to fix this mismatch
[ 9.449265] ubi0: scanning is finished
[ 9.463968] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.486940] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.509906] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.532845] ubi0 error: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read 22528 bytes
Fixes: f9ecf10cb88c ("ARM: dts: imx6ull: add MYiR MYS-6ULX SBC")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 221c3a09ddf70a0a51715e6c2878d8305e95c558 upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb10a ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c69c8a1736eace8de491d480e6e577a27c2087c upstream.
Fix the whole mux-mask table according to datasheet for the sam9x60
product. Too much functions for pins were disabled leading to
misunderstandings when enabling more peripherals or taking this table
as an example for another board.
Take advantage of this fix to move the mux-mask in the SoC file where it
belongs and use lower case letters for hex numbers like everywhere in
the file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210310152006.15018-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 664979bba8169d775959452def968d1a7c03901f upstream.
According to the datasheet PA7 can be set to either function A, B or
C (see table 6-2 of DS60001579D). The previous value would permit just
configuring with function C.
Signed-off-by: Federico Pellegrin <fede@evolware.org>
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e3f828bd4bf5e4eb4214dc4eb227d8f1c8a877 upstream.
The ARM 'adrl' pseudo instruction is a bit problematic, as it does not
exist in Thumb mode, and it is not implemented by Clang either. Since
the Thumb variant has a slightly bigger range, it is sometimes necessary
to emit the 'adrl' variant in ARM mode where Thumb mode can use adr just
fine. However, that still leaves the Clang issue, which does not appear
to be supporting this any time soon.
So let's switch to the adr_l macro, which works for both ARM and Thumb,
and has unlimited range.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d050d049f8b8077025292c1ecf456c4ee7f96861 upstream.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201202051634.490-2-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2acb909750431030b65a0a2a17fd8afcbd813a84 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448dfa78e3e58186c934449aaf6d49b50 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ecdfc1830eaa40a11d7f832089c82b0e67ea96 ]
Split up the pins for each fan. This is needed in order to control them
Fixes: ced8025b569e ("ARM: dts: armada388-helios4")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a442600b006ef7dec3a6dc98bcf59c6 ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb8878 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e7d9a583a24f7582c6bc29a0d4d624feedbc2f9 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: aac4e0615341 ("ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac8893c4fa3d4a34915dc5cdab568a39db5086c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 1fed2252713e ("ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467cb8657cf8b5e610a30a4c502085e4f9 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb0a ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437ae60947716bb479e2f32466f49445c0509b1e ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: faaf348ef468 ("ARM: dts: Add board dts file for exynos3250-rinato")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8528cda2b7c667e9cd173aef1a677c71b7d5a096 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: e0cefb3f79d3 ("ARM: dts: add board dts file for Exynos3250-based Monk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb31334687db31c691901269d65074a7ffaecb18 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: b004a34bd0ff ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]
This reverts commit c17e9377aa81664d94b4f2102559fcf2a01ec8e7.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 181739822cf6f8f4e12b173913af2967a28906c0 upstream.
With the arrival of
commit 2fee9583198eb9 ("spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors")
it was clarified what the proper state for cs-gpios should be, even if the
flag is ignored. The driver code is doing the right thing since
766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
The chip-select of the td028ttec1 panel is active-low, so we must omit spi-cs-high;
attribute (already removed by separate patch) and should now use GPIO_ACTIVE_LOW for
the client device description to be fully consistent.
Fixes: 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07af7810e0a5bc4e51682c90f9fa19fc4cb93f18 upstream.
This reverts
commit f1f028ff89cb ("DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again")
which had to be intruduced after
commit 6953c57ab172 ("gpio: of: Handle SPI chipselect legacy bindings")
broke the GTA04 display. This contradicted the data sheet but was the only
way to get it as an spi client operational again.
The panel data sheet defines the chip-select to be active low.
Now, with the arrival of
commit 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
the logic of interaction between spi-cs-high and the gpio descriptor flags
has been changed a second time, making the display broken again. So we have
to remove the original fix which in retrospect was a workaround of a bug in
the spi subsystem and not a feature of the panel or bug in the device tree.
With this fix the device tree is back in sync with the data sheet and
spi subsystem code.
Fixes: 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a900cac3750b9f0b8f5ed0503d9c6359532f644d ]
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dcd9 ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d411224025ac1baab981e3d2f5d29e7761541d ]
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
