IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 103bde372f084206c6972be543ecc247ebbff9f3 ]
When CONFIG_INET is not set, there are failing references to IPv4
functions, so make this driver depend on INET.
Fixes these build errors:
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_start_xmit_common':
sunvnet_common.c:(.text+0x1a68): undefined reference to `__icmp_send'
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_poll_common':
sunvnet_common.c:(.text+0x358c): undefined reference to `ip_send_check'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aaron Young <aaron.young@oracle.com>
Cc: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5a20573a926302b233b0c2e1077f5debc7ab2e ]
When VSI set up failed in i40e_probe() as part of PF switch set up
driver was trying to free misc IRQ vectors in
i40e_clear_interrupt_scheme and produced a kernel Oops:
Trying to free already-free IRQ 266
WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300
Workqueue: events work_for_cpu_fn
RIP: 0010:__free_irq+0x9a/0x300
Call Trace:
? synchronize_irq+0x3a/0xa0
free_irq+0x2e/0x60
i40e_clear_interrupt_scheme+0x53/0x190 [i40e]
i40e_probe.part.108+0x134b/0x1a40 [i40e]
? kmem_cache_alloc+0x158/0x1c0
? acpi_ut_update_ref_count.part.1+0x8e/0x345
? acpi_ut_update_object_reference+0x15e/0x1e2
? strstr+0x21/0x70
? irq_get_irq_data+0xa/0x20
? mp_check_pin_attr+0x13/0xc0
? irq_get_irq_data+0xa/0x20
? mp_map_pin_to_irq+0xd3/0x2f0
? acpi_register_gsi_ioapic+0x93/0x170
? pci_conf1_read+0xa4/0x100
? pci_bus_read_config_word+0x49/0x70
? do_pci_enable_device+0xcc/0x100
local_pci_probe+0x41/0x90
work_for_cpu_fn+0x16/0x20
process_one_work+0x1a7/0x360
worker_thread+0x1cf/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x1f/0x40
The problem is that at that point misc IRQ vectors
were not allocated yet and we get a call trace
that driver is trying to free already free IRQ vectors.
Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED
PF state before calling i40e_free_misc_vector. This state is set only if
misc IRQ vectors were properly initialized.
Fixes: c17401a1dd21 ("i40e: use separate state bit for miscellaneous IRQ setup")
Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857b6c6f665cca9828396d9743faf37fd09e9ac3 ]
The loop in i40e_get_capabilities can never end. The problem is that
although i40e_aq_discover_capabilities returns with an error if there's
a firmware problem, the returned error is not checked. There is a check for
pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most
firmware problems.
When i40e_aq_discover_capabilities encounters a firmware problem, it will
encounter the same problem on its next invocation. As the result, the loop
becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking
at the code, it can happen with a range of other firmware errors.
I don't know what the correct behavior should be: whether the firmware
should be retried a few times, or whether pf->hw.aq.asq_last_status should
be always set to the encountered firmware error (but then it would be
pointless and can be just replaced by the i40e_aq_discover_capabilities
return value). However, the current behavior with an endless loop under the
rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we
explained the bug to them 7 months ago.
This may not be the best possible fix but it's better than hanging the whole
system on a firmware bug.
Fixes: 56a62fc86895 ("i40e: init code and hardware support")
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17c37d748f2b122a95b6d0524d410302ff89a2b1 ]
Each tx queue maintains a 64bit counter for bytes, there is
no reason to truncate this to 32bit (or this has not been
documented)
Fixes: 24aeb56f2d38 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yangchun Fu <yangchun@google.com>
Cc: Kuo Zhao <kuozhao@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f57d4975fa027eabd35fdf23a49f8222ef3abf2 ]
gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry()
returns true.
What is needed here is to sample values in temporary variables,
and only use them after each loop is ended.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Catherine Sullivan <csully@google.com>
Cc: Sagi Shahar <sagis@google.com>
Cc: Jon Olson <jonolson@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Luigi Rizzo <lrizzo@google.com>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Tao Liu <xliutaox@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922aa9bcac92b3ab6a423526a8e785b35a60b441 ]
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: 893ce44df5658 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sully <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d03477ee10f4bc35d3573cf1823814378ef2dca2 ]
The qpl_map_size is rounded up to a multiple of sizeof(long), but the
number of qpls doesn't have to be.
Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25a9da6641f1f66006e93ddbefee13a437efa8c0 ]
The string should be "tx_disable" to match the state enum.
Fixes: 4005a7cb4f55 ("net: phy: sftp: print debug message with text, not numbers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca6e11c337daf7925ff8a2aac8e84490a8691905 ]
Syzbot reported memory leak in MDIO bus interface, the problem was in
wrong state logic.
MDIOBUS_ALLOCATED indicates 2 states:
1. Bus is only allocated
2. Bus allocated and __mdiobus_register() fails, but
device_register() was called
In case of device_register() has been called we should call put_device()
to correctly free the memory allocated for this device, but mdiobus_free()
calls just kfree(dev) in case of MDIOBUS_ALLOCATED state
To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED
_before_ calling device_register(), because put_device() should be
called even in case of device_register() failure.
Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/
Fixes: 46abc02175b3 ("phylib: give mdio buses a device tree presence")
Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a10440f0b1f33faa792af26f4e9823a9b8b6a4 ]
Currently in Rx data path IPsec crypto offloaded packets uses
csum_none flag, so checksum is handled by the stack, this naturally
have some performance/cpu utilization impact on such flows. As Nvidia
NIC starting from ConnectX6DX provides checksum complete value out of
the box also for such flows there is no sense in taking csum_none path,
furthermore the stack (xfrm) have the method to handle checksum complete
corrections for such flows i.e. IPsec trailer removal and consequently
checksum value adjustment.
Because of the above and in addition the ConnectX6DX is the first HW
which supports IPsec crypto offload then it is safe to report csum
complete for IPsec offloaded traffic.
Fixes: b2ac7541e377 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c735d0d47b495be6753d6aea4f8f78c909a0a ]
There is a Killer AX1650 2x2 Wi-Fi 6 and Bluetooth 5.1 wireless adapter
found on Dell XPS 15 (9510) laptop, its configuration was present on
Linux v5.7, however accidentally it has been removed from the list of
supported devices, let's add it back.
The problem is manifested on driver initialization:
Intel(R) Wireless WiFi driver for Linux
iwlwifi 0000:00:14.3: enabling device (0000 -> 0002)
iwlwifi: No config found for PCI dev 43f0/1651, rev=0x354, rfid=0x10a100
iwlwifi: probe of 0000:00:14.3 failed with error -22
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213939
Fixes: 3f910a25839b ("iwlwifi: pcie: convert all AX101 devices to the device tables")
Cc: Julien Wajsberg <felash@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Luca Coelho <luca@coelho.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210924122154.2376577-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb8c3a3c52400512fc8b3b61150057b888c30b0d ]
Randconfig builds still show a failure for the ath5k driver,
similar to the one that was fixed for ath9k earlier:
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- ATH5K [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && (PCI [=y] || ATH25) && MAC80211 [=y]
net/mac80211/led.c: In function 'ieee80211_alloc_led_names':
net/mac80211/led.c:34:22: error: 'struct led_trigger' has no member named 'name'
34 | local->rx_led.name = kasprintf(GFP_KERNEL, "%srx",
| ^
Copying the same logic from my ath9k patch makes this one work
as well, stubbing out the calls to the LED subsystem.
Fixes: b64acb28da83 ("ath9k: fix build error with LEDS_CLASS=m")
Fixes: 72cdab808714 ("ath9k: Do not select MAC80211_LEDS by default")
Fixes: 3a078876caee ("ath5k: convert LED code to use mac80211 triggers")
Link: https://lore.kernel.org/all/20210722105501.1000781-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210920122359.353810-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ede7f84c7c21f93c5eac611d60eba3f2c765e0f ]
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the
special considerations for the head of the SKB no longer apply. Don't
mistakenly report ERROR to the frontend for the first entry in the list,
even if - from all I can tell - this shouldn't matter much as the overall
transmit will need to be considered failed anyway.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9579976f724ad517cc15b7caadea728c7e245c ]
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726e9 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dcb713d53e2eadf42b878c12a471e74dc6ed3145 upstream.
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport this cleanup patch to 5.10 and 5.14 in order to keep the
codebase consistent with the 4.14/4.19/5.4 patchseries]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d88fd1b546ff19c8040cfaea76bf16aed1c5a0bb ]
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a6998 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27bf4af69fcb9845fb2f0076db5d562ec072e70f ]
Currently, the rx vlan filter will always be disabled before selftest and
be enabled after selftest as the rx vlan filter feature is fixed on in
old device earlier than V3.
However, this feature is not fixed in some new devices and it can be
disabled by user. In this case, it is wrong if rx vlan filter is enabled
after selftest. So fix it.
Fixes: bcc26e8dc432 ("net: hns3: remove unused code in hns3_self_test()")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c8dab1c709c5a715bce14efdb8f4e889d86aa04 ]
This patch reconstructs function hns3_self_test to reduce the code
cycle complexity and make code more concise.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1e144d7dc3c55aa4d451e3a23cd8f34cd65ee01 ]
Correct a report warning in hns3_ethtool.c
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108b3c7810e14892c4a1819b1d268a2c785c087c ]
Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.
To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.
Fixes: 72110b567479 ("net: hns3: return 0 and print warning when hit duplicate MAC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0472e95ffeac8e61259eec17ab61608c6b35599d ]
HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable
multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is
supposed to set when enable multiple TCs with ets. But
the driver mixed the flags when updating the tm configuration.
Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE
too, so remove the unnecessary limitation.
Fixes: 5a5c90917467 ("net: hns3: add support for tc mqprio offload")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78e5b6a6764cb6e83668806b63d74566db36399 ]
Bellow HNAE3_DEVICE_VERSION_V3, MAC pause mode just support one
TC, when enabled multiple TCs, force enable PFC mode.
HNAE3_DEVICE_VERSION_V3 can support MAC pause mode on multiple
TCs, so when enable multiple TCs, just keep MAC pause mode,
and enable PFC mode just according to the user settings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513e605d7a9ce136886cb42ebb2c40e9a6eb6333 ]
The ixgbe driver currently generates a NULL pointer dereference with
some machine (online cpus < 63). This is due to the fact that the
maximum value of num_xdp_queues is nr_cpu_ids. Code is in
"ixgbe_set_rss_queues"".
Here's how the problem repeats itself:
Some machine (online cpus < 63), And user set num_queues to 63 through
ethtool. Code is in the "ixgbe_set_channels",
adapter->ring_feature[RING_F_FDIR].limit = count;
It becomes 63.
When user use xdp, "ixgbe_set_rss_queues" will set queues num.
adapter->num_rx_queues = rss_i;
adapter->num_tx_queues = rss_i;
adapter->num_xdp_queues = ixgbe_xdp_queues(adapter);
And rss_i's value is from
f = &adapter->ring_feature[RING_F_FDIR];
rss_i = f->indices = f->limit;
So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup",
for (i = 0; i < adapter->num_rx_queues; i++)
if (adapter->xdp_ring[i]->xsk_umem)
It leads to panic.
Call trace:
[exception RIP: ixgbe_xdp+368]
RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297
RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90
RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000
R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000
R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc
8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808
9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235
10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384
11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd
12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb
13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88
14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319
15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290
16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8
17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64
18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9
19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c
So I fix ixgbe_max_channels so that it will not allow a setting of queues
to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup,
take the smaller value of num_rx_queues and num_xdp_queues.
Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bb08dd04a05035a64504faa47651d36b0f3125 ]
An object file cannot be built for both loadable module and built-in
use at the same time:
arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common':
ks8851_common.c:(.text+0xf80): undefined reference to `__this_module'
Change the ks8851_common code to be a standalone module instead,
and use Makefile logic to ensure this is built-in if at least one
of its two users is.
Fixes: 797047f875b5 ("net: ks8851: Implement Parallel bus operations")
Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51032e6f17ce990d06123ad7307f258c50d25aa7 ]
The e100_get_regs function is used to implement a simple register dump
for the e100 device. The data is broken into a couple of MAC control
registers, and then a series of PHY registers, followed by a memory dump
buffer.
The total length of the register dump is defined as (1 + E100_PHY_REGS)
* sizeof(u32) + sizeof(nic->mem->dump_buf).
The logic for filling in the PHY registers uses a convoluted inverted
count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and
assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will
fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This
is actually one more than the supposed number of PHY registers.
The memory dump buffer is then filled into the space at
[2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past
the total size.
The end result is that we overrun the total buffer size allocated by the
kernel, which could lead to a panic or other issues due to memory
corruption.
It is difficult to determine the actual total number of registers
here. The only 8255x datasheet I could find indicates there are 28 total
MDI registers. However, we're reading 29 here, and reading them in
reverse!
In addition, the ethtool e100 register dump interface appears to read
the first PHY register to determine if the device is in MDI or MDIx
mode. This doesn't appear to be documented anywhere within the 8255x
datasheet. I can only assume it must be in register 28 (the extra
register we're reading here).
Lets not change any of the intended meaning of what we copy here. Just
extend the space by 4 bytes to account for the extra register and
continue copying the data out in the same order.
Change the E100_PHY_REGS value to be the correct total (29) so that the
total register dump size is calculated properly. Fix the offset for
where we copy the dump buffer so that it doesn't overrun the total size.
Re-write the for loop to use counting up instead of the convoluted
down-counting. Correct the mdio_read offset to use the 0-based register
offsets, but maintain the bizarre reverse ordering so that we have the
ABI expected by applications like ethtool. This requires and additional
subtraction of 1. It seems a bit odd but it makes the flow of assignment
into the register buffer easier to follow.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4329c8dc110b25d5f04ed20c6821bb60deff279f ]
commit abf9b902059f ("e100: cleanup unneeded math") tried to simplify
e100_get_regs_len and remove a double 'divide and then multiply'
calculation that the e100_reg_regs_len function did.
This change broke the size calculation entirely as it failed to account
for the fact that the numbered registers are actually 4 bytes wide and
not 1 byte. This resulted in a significant under allocation of the
register buffer used by e100_get_regs.
Fix this by properly multiplying the register count by u32 first before
adding the size of the dump buffer.
Fixes: abf9b902059f ("e100: cleanup unneeded math")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c587fed61cf88bd45822c3159644445f6d5aa6 ]
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ce2f54c0f0ff781e914ec189c25f7bf1b1ec2 ]
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe23036192c95b66e60d019d2ec1814d0d561ffd ]
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ab8a447bcfee1ded709e7ff5dc7608ca9f66ae2 ]
After commit 05b35e7eb9a1 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 325fd36ae76a6d089983b2d2eccb41237d35b221 ]
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: c76a97218dcb ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bbd1990b6ddfdaa7da098d0c56b098a833572 ]
Thomas explained in https://lore.kernel.org/r/87mtoeb4hb.ffs@tglx
that our handling of the hrtimer here is wrong: If the timer fires
late (e.g. due to vCPU scheduling, as reported by Dmitry/syzbot)
then it tries to actually rearm the timer at the next deadline,
which might be in the past already:
1 2 3 N N+1
| | | ... | |
^ intended to fire here (1)
^ next deadline here (2)
^ actually fired here
The next time it fires, it's later, but will still try to schedule
for the next deadline (now 3), etc. until it catches up with N,
but that might take a long time, causing stalls etc.
Now, all of this is simulation, so we just have to fix it, but
note that the behaviour is wrong even per spec, since there's no
value then in sending all those beacons unaligned - they should be
aligned to the TBTT (1, 2, 3, ... in the picture), and if we're a
bit (or a lot) late, then just resume at that point.
Therefore, change the code to use hrtimer_forward_now() which will
ensure that the next firing of the timer would be at N+1 (in the
picture), i.e. the next interval point after the current time.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+0e964fad69a9c462bc1e@syzkaller.appspotmail.com
Fixes: 01e59e467ecf ("mac80211_hwsim: hrtimer beacon")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210915112936.544f383472eb.I3f9712009027aa09244b65399bf18bf482a8c4f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0d2a46c0141913dc6fd126c57d0615677d946e ]
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff2d13114f0beec448da9b3716204eb34b0cf41 ]
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08dad2f4d541fcfe5e7bfda72cc6314bbfd2802f ]
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d82d5303c4c539db86588ffb5dc5b26c3f1513e8 ]
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea269a6f720782ed94171fb962b14ce07c372138 ]
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d88c339c423eefe2fd48215016cb0c75fcb4c4d ]
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 57f780f1c433 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdbccea419dc782079ce5881d2705cc9e3881480 ]
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes: 1eb8c695bda9 ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ea7812326004afd2803cc968a4776ae5120a597 ]
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 64515dc899df ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74b6d7d13307b016f4b5bba8198297824c0ee6df ]
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b1279d9905100a14da9e043de7b28e99dba3f8 ]
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes: d34100184685 ("net: hns3: refactor the mailbox message between PF and VF")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e184cec5e29d8eb3c3435b12a9074b75e2d69e4a ]
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 374ad291762a ("net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bed8b0704c9ecccc8f4a2c377d7c8e21090a82e ]
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7afa05c9522b086327929ae622facab0f0f72b ]
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d1627 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7237a494decfa17d0b9d0076e6cee3235719de90 ]
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8f69b16ee776da88589b5271e3f46020efc8f6c upstream.
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c70 ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fe6322774ca28669868a7e231e173e09f7422118 which was
commit 82e6c96f04e13c72d91777455836ffd012853caa upstream.
It has been reported to cause regressions so should be dropped.
Reported-by: <Patrick.Mclean@sony.com>
Link: https://lore.kernel.org/r/BY5PR13MB3604D3031E984CA34A57B7C9EEA09@BY5PR13MB3604.namprd13.prod.outlook.com
Cc: Aya Levin <ayal@nvidia.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
