IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 51f93add3669f1b1f540de1cf397815afbd4c756 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22414cade8dfec25ab94df52b3a4f7aa8edb6120 ]
The default SOF topology enables SSP capture and DMICs, even though
both of these hardware capabilities are not always available in
hardware (specific versions of HiFiberry and DMIC kit needed).
For the SSP capture, this leads to annoying "SP5-Codec: ASoC: no
backend capture" and "streamSSP5-Codec: ASoC: no users capture at
close - state 0" errors.
Update the quirks to match what the topology needs, which also allows
for the ability to remove SSP capture and DMIC support.
BugLink: https://github.com/thesofproject/linux/issues/3061
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dccd1dfd0770bfd494b68d1135b4547b2c602c42 ]
Move the "Platform Clock" routes for the "Internal Mic" and "Speaker"
routes to the intmic_*_map[] / *_spk_map[] arrays.
This ensures that these "Platform Clock" routes do not get added when the
BYT_RT5640_NO_INTERNAL_MIC_MAP / BYT_RT5640_NO_SPEAKERS quirks are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2942a8b7c38e8cc2d5157b4f0323d7f4e5ec71 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 818c4593434e81c9971b8fc278215121622c755e ]
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reported-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 220ade77452c15ecb1ab94c3f8aaeb6d033c3582 ]
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e6bc5987a5252948e3411e5a2dbb434fd1ea107 ]
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aec45d7884f16cc21d668693c5b88bff8df0f02 ]
Fix the following dtbs_check warning:
cs42l51@4a: port:endpoint@0:frame-master: True is not of type 'array'
cs42l51@4a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a79e78c391dc074742c855dc0108a88f781d56a3 ]
Fix the following dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:frame-master: True is not of type 'array'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f728c4a9e8405caae69d4bc1232c54ff57b5d20f ]
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92fe24a7db751b80925214ede43f8d2be792ea7b ]
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
Link: https://syzkaller.appspot.com/bug?extid=66264bf2fd0476be7e6c [1]
Reported-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Tested-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ad4a31620355358316fa08fcfab37b9d6c33347 ]
Last change to device managed APIs cleaned up error path to simple phy_exit()
call, which in some cases has been executed with NULL parameter. This per se
is not a problem, but rather logical misconception: no need to free resource
when it's for sure has not been allocated yet. Fix the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210727125130.19977-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 043c5bb3c4f43670ab4fea0b847373ab42d25f3e ]
When loading in parallel multiple programs which use the same to-be
pinned map, it is possible that two instances of the loader will call
bpf_object__create_maps() at the same time. If the map doesn't exist
when both instances call bpf_object__reuse_map(), then one of the
instances will fail with EEXIST when calling bpf_map__pin().
Fix the race by retrying reusing a map if bpf_map__pin() returns
EEXIST. The fix is similar to the one in iproute2: e4c4685fd6e4 ("bpf:
Fix race condition with map pinning").
Before retrying the pinning, we don't do any special cleaning of an
internal map state. The closer code inspection revealed that it's not
required:
- bpf_object__create_map(): map->inner_map is destroyed after a
successful call, map->fd is closed if pinning fails.
- bpf_object__populate_internal_map(): created map elements is
destroyed upon close(map->fd).
- init_map_slots(): slots are freed after their initialization.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210726152001.34845-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d07006f05922b95518be403f08ef8437b67aa32 ]
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210727041056.23455-1-claudiajkang@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56315e55119c0ea57e142b6efb7c31208628ad86 ]
'sleep_status' has 3 atomic_t members. Initialize the 3 of them instead of
initializing only 2 of them and setting 0 twice to the same variable.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d2e52a33a9beab41879551d0ae2fdfc99970adab.1626856991.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ]
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ccbdcc4d08a6d7041e4849219bbb12ffa45db4c ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23411c720052ad860b3e579ee4873511e367130a ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7aff291d069c4418285f3c8ee27b0ff67ce5998 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3322ba0d7bea1e24ae464418626f6a15b69533ab ]
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5492886c14744d239e87f1b0b774b5a341e755cc ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323e0cb473e2a8706ff162b6b4f4fa16023c9ba7 ]
Fix the following out-of-bounds warnings:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6321c7acb82872ef6576c520b0e178eaad3a25c0 ]
Fix the following out-of-bounds warning:
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ab1f6539762946de06ca14d7401ae123821bc40 ]
Regulator node names don't reflect class of the device. Fix that by
prefixing names with "regulator-".
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722161220.51181-2-jernej.skrabec@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47956bc86ee4e8530cac386a04f62a6095f7afbe ]
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb82941a86b4e35c4fcfb1ef5a5cfad7c1fceab.1626255956.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b7e9f25e590726cca76700ebdb10e92a7a72ca1 ]
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721103822.3755111-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae7f47041d928b1a2f28717d095b4153c63cbf6a ]
This test now operates on DW as stated instead of W, which was
already covered by another test.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721104058.3755254-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f71f12aa45d65b7f2ccab95569795edffd379a ]
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd98d2895de6485c884a9cb42de69fed02826fa4 ]
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c48200 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4431531c482a2c05126caaa9fcc5053a4a5c495b ]
The return type of the function is bool and while NULL do evaluate to
false it's not very nice, fix this by explicitly returning false. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 672fe1cf145ab9978c62eb827d6a16aa6b63994b ]
When hmm_pool_register() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Link: https://lore.kernel.org/linux-media/20210408081850.24278-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ad61a7847da09b6261824accb539d05bcdfef65 ]
When the VP8 decoders can't find a reference frame,
the driver falls back to the current output frame.
This will probably produce some undesirable results,
leading to frame corruption, but shouldn't cause
noisy warnings.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23e55639b87fb16a9f0f66032ecb57060df6c46c ]
[why]
The units of the time_per_pixel variable were incorrect, this had to be
changed for the code to properly function.
[how]
The change was very straightforward, only required one line of code to
be changed where the calculation was done.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8990f96a012f42543005b07d9e482694192e9309 ]
Some versions of the MC firmware wrongly report 0 for register base
address of the DPMCP associated with child DPRC objects thus rendering
them unusable. This is particularly troublesome in ACPI boot scenarios
where the legacy way of extracting this base address from the device
tree does not apply.
Given that DPMCPs share the same base address, workaround this by using
the base address extracted from the root DPRC container.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20210715140718.8513-8-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df00609821bf17f50a75a446266d19adb8339d84 ]
On Armadillo-800-EVA with CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/1
lock: lcdc0_device+0x10c/0x308, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 1 Comm: swapper Not tainted 5.11.0-rc5-armadillo-00036-gbbca04be7a80-dirty #287
Hardware name: Generic R8A7740 (Flattened Device Tree)
[<c010c3c8>] (unwind_backtrace) from [<c010a49c>] (show_stack+0x10/0x14)
[<c010a49c>] (show_stack) from [<c0159534>] (do_raw_spin_lock+0x20/0x94)
[<c0159534>] (do_raw_spin_lock) from [<c040858c>] (dev_pm_get_subsys_data+0x8c/0x11c)
[<c040858c>] (dev_pm_get_subsys_data) from [<c05fbcac>] (genpd_add_device+0x78/0x2b8)
[<c05fbcac>] (genpd_add_device) from [<c0412db4>] (of_genpd_add_device+0x34/0x4c)
[<c0412db4>] (of_genpd_add_device) from [<c0a1ea74>] (board_staging_register_device+0x11c/0x148)
[<c0a1ea74>] (board_staging_register_device) from [<c0a1eac4>] (board_staging_register_devices+0x24/0x28)
of_genpd_add_device() is called before platform_device_register(), as it
needs to attach the genpd before the device is probed. But the spinlock
is only initialized when the device is registered.
Fix this by open-coding the spinlock initialization, cfr.
device_pm_init_common() in the internal drivers/base code, and in the
SuperH early platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/57783ece7ddae55f2bda2f59f452180bff744ea0.1626257398.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcacbf06c891374e7fdd7b72d11cda03b0269b43 ]
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
Co-developed-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210720080907.30292-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61136a12cbed234374ec6f588af57c580b20b772 ]
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae01239609b29ec2eff55967c8e0fe3650cfa09 ]
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 091cb2f782f32ab68c6f5f326d7868683d3d4875 ]
We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e898764245c852bc8ee4857613ba4f3a6d761d ]
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we should make use of the
usb_endpoint_* helpers instead and remove the unnecessary
max_packet()/hb_mult() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-3-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 373e2829e7c2e1e606503cdb5c97749f512a4be9 ]
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed31a4dd3adb5455df7c704de2abb639a1dc1c0 ]
This commit fixes several typos where CONFIG_TASKS_RCU_TRACE should
instead be CONFIG_TASKS_TRACE_RCU. Among other things, these typos
could cause CONFIG_TASKS_TRACE_RCU_READ_MB=y kernels to suffer from
memory-ordering bugs that could result in false-positive quiescent
states and too-short grace periods.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
