IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 9472335eaa1452b51dc8e8edaa1a342997cb80c7 upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571833 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4ca0c439f2d5ce9a3dc118d882f9f03449864c8 upstream.
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
Fixes: 4da712e70294 ("mtd: nand: fsmc: use ->exec_op()")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-4-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e3cdba176ba59eaf4d463d273da0718e3626140 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf3a ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325fd539fc84f0aaa0ceb9d7d3b8718582473dc5 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6aab ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194ac63de6ff56d30c48e3ac19c8a412f9c1408e upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2e8 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16b7d2a5e810fcf4b15d096246d0d445da9cc88 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042b2 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b5b4dc6fcd8194b9dd38c8acdc5ab71adf44f8 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448e0 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d8570b7fd6f4f08528ce2f5e39787a8a260cd6 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b72 ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcd2960af1b7bacb2f1e710ab0c0b802d900501 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5bd8 ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d707bb74daae07879e0fc1b4b960f8f2d0a5fe5d upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d93473323a ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c13de2386c78e890d4ae6f01a85eefd0b293fb08 ]
Previously, if del_mtd_device() failed with -EBUSY due to a non-zero
usecount, a subsequent call to attempt the deletion again would try to
remove a debugfs directory that had already been removed and panic.
With this change the second call can instead proceed safely.
Fixes: e8e3edb95ce6 ("mtd: create per-device and module-scope debugfs entries")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211014203953.5424-1-zev@bewilderbeest.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e4d342187625585932bb437ec26e1060f7fc6f ]
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141bd ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b4ebddd6540d78a7f977b3fea0261bd575c6ffe2 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe5d ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b430c7595e4eb95fae8fb54adc3c3ce002e75ae ]
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: 8c61b7a7f4d4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e282be95ae76125dddc79515541efeb ]
Since 2431c4f5b46c3 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b46c3 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
The new generic NAND ECC framework stores the configuration and
requirements in separate places since commit 93ef92f6f422 ("mtd: nand: Use
the new generic ECC object"). In 5.10.x The SPI NAND layer still uses only
the requirements to track the ECC properties. This mismatch leads to
values of zero being used for ECC strength and step_size in the SPI NAND
layer wherever nanddev_get_ecc_conf() is used and therefore breaks the SPI
NAND on-die ECC support in 5.10.x.
By using nanddev_get_ecc_requirements() instead of nanddev_get_ecc_conf()
for SPI NAND, we make sure that the correct parameters for the detected
chip are used. In later versions (5.11.x) this is fixed anyway with the
implementation of the SPI NAND on-die ECC engine.
Cc: stable@vger.kernel.org # 5.10.x
Reported-by: voice INTER connect GmbH <developer@voiceinterconnect.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2394e628738933aa014093d93093030f6232946d upstream.
Erasing an AMD linear flash card (AM29F016D) crashes after the first
sector has been erased. Likewise, writing to it crashes after two bytes
have been written. The reason is a missing check for a null pointer -
the cmdset_priv field is not set for this type of card.
Fixes: 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Andreas Persson <andreasp56@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/DB6P189MB05830B3530B8087476C5CFE4C1159@DB6P189MB0583.EURP189.PROD.OUTLOOK.COM
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5437c7b682c9a505065b4ab4716cdc951dc3c7c ]
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 237960880960863fb41888763d635b384cffb104 ]
fis-index-block is seeked in the master node and not in the partitions node.
For following binding and current usage, the driver need to check the
partitions subnode.
Fixes: c0e118c8a1a3 ("mtd: partitions: Add OF support to RedBoot partitions")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210520114851.1274609-1-clabbe@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 076de75de1e53160e9b099f75872c1f9adf41a0b ]
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9afe6 ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e97743fd180981bef5f01402342bb54bf1c6366 ]
MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require
write permission. Depending on the hardware MEMLOCK might even be
write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK
is always write-once.
MEMSETBADBLOCK modifies the bad block table.
Fixes: f7e6b19bc764 ("mtd: properly check all write ioctls for permissions")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303155735.25887-1-michael@walle.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 620b90d30c08684dc6ebee07c72755d997f9d1f6 ]
When platform_get_drvdata() returns NULL to info, no error return code
of physmap_flash_remove() is assigned.
To fix this bug, err is assigned with -EINVAL in this case
Fixes: 73566edf9b91 ("[MTD] Convert physmap to platform driver")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210308034446.3052-1-baijiaju1990@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55fbb9ba4f06cb6aff32daca1e1910173c13ec51 ]
In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.
So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.
Fixes: c76b78d8ec05 ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08608adb520e51403be7592c2214846fa440a23a ]
There are chances that the parse_mtd_partitions() function will return
-EPROBE_DEFER in mtd_device_parse_register(). This might happen when
the dependency is not available for the parser. For instance, on SDX55
the MTD_QCOMSMEM_PARTS parser depends on the QCOM_SMEM driver to parse
the partitions defined in the shared memory region. With the current
flow, the error returned from parse_mtd_partitions() will be discarded
in favor of trying to add the fallback partition.
This will prevent the driver to end up in probe deferred pool and the
partitions won't be parsed even after the QCOM_SMEM driver is available.
Fix this issue by bailing out of mtd_device_parse_register() when
-EPROBE_DEFER error is returned from parse_mtd_partitions() function and
propagate the error code to the driver core for probing later.
Fixes: 5ac67ce36cfe ("mtd: move code adding (registering) partitions to the parse_mtd_partitions()")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5200c14242fb8fa4a9b93f7fd4064d237e58785 ]
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7a97528e3c787802d8c643d6ab2f428511bb047 ]
If dma_request_channel() fails then the probe fails and it should
return a negative error code, but currently it returns success.
fixes: 4774fb0a48aa ("mtd: nand/fsmc: Add DMA support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YCqaOZ83OvPOzLwh@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 683313993dbe1651c7aa00bb42a041d70e914925 upstream.
Cast &data to (char *) in order to avoid unintentionally accessing
the stack.
Notice that data is of type u32, so any increment to &data
will be in the order of 4-byte chunks, and this piece of code
is actually intended to be a byte offset.
Fixes: b3e79e7682e0 ("mtd: physmap: Add Baikal-T1 physically mapped ROM support")
Addresses-Coverity-ID: 1497765 ("Out-of-bounds access")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210212104022.GA242669@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25fefc88c71f47db0466570335e3f75f10952e7a upstream.
The module misses MODULE_DEVICE_TABLE() for both SPI and OF ID tables
and thus never autoloads on ID matches.
Add the missing declarations.
Present since day-0 of spinand framework introduction.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323173714.317884-1-alobakin@pm.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46094049a49be777f12a9589798f7c70b90cd03f upstream.
This reverts commit 04b8edad262eec0d153005973dfbdd83423c0dcb.
mx25l51245g and mx66l51235l have the same flash ID. The flash
detection returns the first entry in the flash_info array that
matches the flash ID that was read, thus for the 0xc2201a ID,
mx25l51245g was always hit, introducing a regression for
mx66l51235l.
If one wants to differentiate the flash names, a better fix would be
to differentiate between the two at run-time, depending on SFDP,
and choose the correct name from a list of flash names, depending on
the SFDP differentiator.
Fixes: 04b8edad262e ("mtd: spi-nor: macronix: Add support for mx25l51245g")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210402082031.19055-2-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be94215be1ab19e5d38f50962f611c88d4bfc83a upstream.
If rmmod the driver during read or write, the driver will release the
resources which are used during read or write, so it is possible to
refer to NULL pointer.
Use the testcase "mtd_debug read /dev/mtd0 0xc00000 0x400000 dest_file &
sleep 0.5;rmmod spi_hisi_sfc_v3xx.ko", the issue can be reproduced in
hisi_sfc_v3xx driver.
To avoid the issue, fill the interface _get_device and _put_device of
mtd_info to grab the reference to the spi controller driver module, so
the request of rmmod the driver is rejected before read/write is finished.
Fixes: b199489d37b2 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1617262486-4223-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2fb164f0ce95e504e2688b4f984893c29ebd19ab ]
This fixes NAND_OP_WAITRDY_INSTR operation in the driver. Without this
change the driver waits till the system is busy, but we should wait till
the busy flag is cleared. The readl_poll_timeout() function gets a break
condition, not a wait condition.
In addition fix the timeout. The timeout_ms is given in ms, but the
readl_poll_timeout() function takes the timeout in us. Multiple the
given timeout by 1000 to convert it.
Without this change, the driver does not work at all, it doesn't even
identify the NAND chip.
Fixes: 5197360f9e09 ("mtd: rawnand: mtk: Convert the driver to exec_op()")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210309000107.1368404-1-hauke@hauke-m.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe6653460ee7a7dbe0cd5fd322992af862ce5ab0 upstream.
Put the child node np when it fails to get or register device.
Fixes: e523f11141bd ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Pan Bian <bianpan2016@163.com>
[ta: Add Fixes tag and Cc stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210121091847.85362-1-bianpan2016@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58fa22f68fcaff20ce4d08a6adffa64f65ccd37d upstream.
Even if erase type is same as previous region, erase size can be different
if the previous region is overlaid region. Since 'region->size' is assigned
to 'cmd->size' for overlaid region, comparing 'erase->size' and 'cmd->size'
can detect previous overlaid region.
Fixes: 5390a8df769e ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/13d47e8d8991b8a7fd8cc7b9e2a5319c56df35cc.1601612872.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 969b276718de37dfe66fce3a5633f611e8cd58fd upstream.
In case of overlaid regions in which their biggest erase size command
overpasses in size the region's size, only the non-overlaid portion of
the sector gets erased. For example, if a Sector Erase command is applied
to a 256-kB range that is overlaid by 4-kB sectors, the overlaid 4-kB
sectors are not affected by the erase.
For overlaid regions, 'region->size' is assigned to 'cmd->size' later in
spi_nor_init_erase_cmd(), so 'erase->size' can be greater than 'len'.
Fixes: 5390a8df769e ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Update commit description, add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/fa5d8b944a5cca488ac54ba37c95e775ac2deb34.1601612872.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abdf5a5ef9652bad4d58058bc22ddf23543ba3e1 upstream.
At the time spi_nor_region_check_overlay() is called, the erase types are
sorted in ascending order of erase size. The 'erase_type' should be masked
with 'BIT(erase[i].idx)' instead of 'BIT(i)'.
Fixes: b038e8e3be72 ("mtd: spi-nor: parse SFDP Sector Map Parameter Table")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/fd90c40d5b626a1319a78fc2bcee79a8871d4d57.1601612872.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9166f4af32db74e1544a2149aef231ff24515ea3 upstream.
The place of spi_nor_region_mark_end() must be moved, because 'i' is
re-used for the index of erase[].
Fixes: b038e8e3be72 ("mtd: spi-nor: parse SFDP Sector Map Parameter Table")
Cc: stable@vger.kernel.org
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
[ta: Add Fixes tag and Cc to stable]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/02ce8d84b7989ebee33382f6494df53778dd508e.1601612872.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b844cf445f0a7daa68be0ce71eb2c88d68b0c5d ]
In the case of failure while parsing the partitions, the iterator should
be pre decremented by one before starting to free the memory allocated
by kstrdup(). Because in the failure case, kstrdup() will not succeed
and thus no memory will be allocated for the current iteration.
Fixes: 1fca1f6abb38 ("mtd: afs: simplify partition parsing")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210104041137.113075-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12ba8f8ce29fdd277f3100052eddc1afd2f5ea3f ]
If the kstrtouint() calls fail, then this should return a negative
error code but it currently returns success.
Fixes: dd84cb022b31 ("mtd: bcm63xxpart: move imagetag parsing to its own parser")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YBKFtNaFHGYBj+u4@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c97be6982e689d7b2430187a11f8c78e573abdb upstream.
I have been fooled by the logic picking the right ECC engine which is
spread across two functions: *init_module() and *_attach(). I thought
this driver was not impacted by the recent changes around the ECC
engines DT parsing logic but in fact it is.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: d7157ff49a5b ("mtd: rawnand: Use the ECC framework user input parsing bits")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210104093057.31178-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4883a60c17eda6bf52d1c817ee7ead65b4a02da2 upstream.
Re-add the multiply by 8 to "step * eccsize" to correct the destination bit offset
when extracting the data payload in gpmi_ecc_read_page_raw().
Fixes: e5e5631cc889 ("mtd: rawnand: gpmi: Use nand_extract_bits()")
Cc: stable@vger.kernel.org
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201221100013.2715675-1-sean@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts stable commit baad618d078c857f99cc286ea249e9629159901f.
This commit is adding lines to spinand_write_to_cache_op, wheras the upstream
commit 868cbe2a6dcee451bd8f87cbbb2a73cf463b57e5 that this was supposed to
backport was touching spinand_read_from_cache_op.
It causes a crash on writing OOB data by attempting to write to read-only
kernel memory.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc3686021122de953858a5be4cbf6e3f1d821e79 upstream.
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6e2 ("mtd: rawnand: qcom: check for operation errors in case of raw read")
Cc: stable@vger.kernel.org
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ca71415f075353974524e96ed175306d8a937a8 upstream.
Apply changes to usecount also to the master partition.
Otherwise we have no refcounting at all if an MTD has no partitions.
Cc: stable@vger.kernel.org
Fixes: 46b5889cc2c5 ("mtd: implement proper partition handling")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201206202220.27290-1-richard@nod.at
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639a82434f16a6df0ce0e7c8595976f1293940fd upstream.
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa022741 ("mtd: parser: cmdline: Support MTD names containing one or more colons")
Cc: stable@vger.kernel.org
Cc: Ron Minnich <rminnich@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868cbe2a6dcee451bd8f87cbbb2a73cf463b57e5 upstream.
So far OOB have never been used in SPI-NAND, add the missing memcpy to
make it work properly.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
