IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 12f371e2b6cb4b79c788f1f073992e115f4ca918 ]
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8774ea7a553e2aec323170d49365b59af0a2b7e0 ]
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd5432c712351a3d5f82512908f5febfca946ca6 ]
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dfcf1ad933fe877cb44e9fb7a661dfc22190101 ]
Set scsi_host_template.cmd_size instead of using the SCSI pointer for
storing driver-private data. Change the type of the argument of
uas_add_work() from struct uas_cmd_info * into struct scsi_cmnd * because
it is easier to convert a SCSI command pointer into a uas_cmd_info pointer
than the other way around.
This patch prepares for removal of the SCSI pointer from struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220218195117.25689-46-bvanassche@acm.org
Cc: linux-usb@vger.kernel.org
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: cd5432c71235 ("USB: UAS: return ENODEV when submit urbs fail with device not attached")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80ba43e9f799cbdd83842fc27db667289b3150f5 upstream.
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124c0 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3de4f996a0b5412aa451729008130a488f71563e upstream.
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b5c85ddeea77d18c4b69e3bda60e9374a20c304 upstream.
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a587a035214fa1b5ef598aea0b81848c5b72e5e upstream.
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d69a3b54e5a630c90d82a4c2bdce3d53dc78710 upstream.
Added functionality to exit from L1 state by device initiation
using remote wakeup signaling, in case when function driver queuing
request while core in L1 state.
Fixes: 273d576c4d41 ("usb: dwc2: gadget: Add functionality to exit from LPM L1 state")
Fixes: 88b02f2cb1e1 ("usb: dwc2: Add core state checking")
CC: stable@vger.kernel.org
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/b4d9de5382375dddbf7ef6049d9a82066ad87d5d.1710166393.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bae2bc73a59c200db53b6c15fb26bb758e2c6108 upstream.
Starting from core v4.30a changed order of programming
GPWRDN_PMUACTV to 0 in case of exit from hibernation on
remote wakeup signaling from device.
Fixes: c5c403dc4336 ("usb: dwc2: Add host/device hibernation functions")
CC: stable@vger.kernel.org
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/99385ec55ce73445b6fbd0f471c9bd40eb1c9b9e.1708939799.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee113b860aa169e9a4d2c167c95d0f1961c6e1b8 upstream.
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339f83612f3a569b194680768b22bf113c26a29d upstream.
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e540c9 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90ce1e04cbcc76639d6cba0fdbd820cd80b3c70 upstream.
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaafa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 014bcf41d946b36a8f0b8e9b5d9529efbb822f49 upstream.
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84fa943d93c31ee978355e6c6c69592dae3c9f59 ]
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c98a ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a8da9ff1395c4879b4bd41e55733d944f3d613 ]
TDK NC0110013M and MM0110113M have custom USB IDs for CP210x,
so we need to add them to the driver.
Signed-off-by: Toru Katagiri <Toru.Katagiri@tdk.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d9d868491a362d421521499d98308c8e3a0398 ]
The radiation meter has the text MGP Instruments PDS-100G or PDS-100GN
produced by Mirion Technologies. Tested by forcing the driver
association with
echo 10c4 863c > /sys/bus/usb-serial/drivers/cp210x/new_id
and then setting the serial port in 115200 8N1 mode. The device
announces ID_USB_VENDOR_ENC=Silicon\x20Labs and ID_USB_MODEL_ENC=PDS100
Signed-off-by: Christian Häggström <christian.haggstrom@orexplore.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb7bc4f3a98c48981318b87cf553c5f115fd5ca ]
The GMC IR-USB adapter cable utilizes a FTDI FT232R chip.
Add VID/PID for this adapter so it can be used as serial device via
ftdi_sio.
Signed-off-by: Daniel Vogelbacher <daniel@chaospixel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be95cc6d71dfd0cba66e3621c65413321b398052 ]
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e58472 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600556809f04eb3bbccd05218215dcd7b285a9a9 ]
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2ec ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c4650ded49e5b88929ecbbb631efb8b0838e811 ]
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5372c65e1311a16351ef03dd096ff576e6477674 ]
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7cdfc319b2bcf6899ab0a05eec0958bc802a9a1 ]
xhci-hub.c tracks suspended ports in a suspended_port bitfield.
This is checked when responding to a Get_Status(PORT) request to see if a
port in running U0 state was recently resumed, and adds the required
USB_PORT_STAT_C_SUSPEND change bit in those cases.
The suspended_port bit was left uncleared if a device is disconnected
during suspend. The bit remained set even when a new device was connected
and enumerated. The set bit resulted in a incorrect Get_Status(PORT)
response with a bogus USB_PORT_STAT_C_SUSPEND change
bit set once the new device reached U0 link state.
USB_PORT_STAT_C_SUSPEND change bit is only used for USB2 ports, but
xhci-hub keeps track of both USB2 and USB3 suspended ports.
Cc: stable@vger.kernel.org
Reported-by: Wesley Cheng <quic_wcheng@quicinc.com>
Closes: https://lore.kernel.org/linux-usb/d68aa806-b26a-0e43-42fb-b8067325e967@quicinc.com/
Fixes: 1d5810b6923c ("xhci: Rework port suspend structures for limited ports.")
Tested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0425784b942fffbbdb804896197f1dbccda37c5 ]
The get port status hub request code in xhci-hub.c will complete usb2
port resume signalling if signalling has been going on for long enough.
The code that completes the resume signalling, and the code that returns
the port status have gotten too intertwined, so separate them a bit.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d7cdfc319b2b ("xhci: track port suspend state correctly in unsuccessful resume cases")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6275452ce26d7ff274a5c1b15ed581a26f7986 ]
Initially resume related USB2 variables were cleared once port
successfully resumed to U0. Later code was added to clean up
stale resume variables in case of port failed to resume to U0.
Clear the variables in one place after port is no longer resuming
or in suspended U3 state.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d7cdfc319b2b ("xhci: track port suspend state correctly in unsuccessful resume cases")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a909d629ae77b97b6288bc3cfe68560454bf79c6 ]
resume_done is just a timestamp, avoid confusing it with completions
related to port state transitions that are named *_done
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d7cdfc319b2b ("xhci: track port suspend state correctly in unsuccessful resume cases")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2996e9fc00c378987c18ecbafe5624581b18c0d6 ]
Now that we have a port structure for each port it makes sense to
move per port variables, timestamps and completions there.
Get rid of storing bitfileds and arrays of port specific items per bus.
Move
unsigned long resume_done;
insigned long rexit_ports
struct completion rexit_done;
struct completion u3exit_done;
Rename rexit_ports to rexit_active, and remove a redundant hcd
speed check while checking if rexit_active is set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d7cdfc319b2b ("xhci: track port suspend state correctly in unsuccessful resume cases")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faaae0190dcd1e230616c85bbc3b339f27ba5b81 ]
Both port number and port structure of a port are referred to several
times when handing hub requests in xhci.
Use more suitable data types and readable names for these.
Cleanup only, no functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: d7cdfc319b2b ("xhci: track port suspend state correctly in unsuccessful resume cases")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b787a3e781759026a6212736ef8e52cf83d1821a upstream.
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c175a ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c9be13846c0b2abc2480602f8ef421360e1ad9e upstream.
In current design, usb role class driver will get usb_role_switch parent's
module reference after the user get usb_role_switch device and put the
reference after the user put the usb_role_switch device. However, the
parent device of usb_role_switch may be removed before the user put the
usb_role_switch. If so, then, NULL pointer issue will be met when the user
put the parent module's reference.
This will save the module pointer in structure of usb_role_switch. Then,
we don't need to find module by iterating long relations.
Fixes: 5c54fcac9a9d ("usb: roles: Take care of driver module reference counting")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76c51146820c5dac629f21deafab0a7039bc3ccd upstream.
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a2b ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fd9e45f1ebcd57181358af28506e8a661a260b3 upstream.
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47625b018c6bc788bc10dd654c82696eb0a5ef11 upstream.
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a6be674306c9acb05c08e5c3fd376ef50a917c upstream.
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e3ef5685393c5051b52cf1e94b8891d49793ab upstream.
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb60136 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39674be56fba1cd3a03bf4617f523a35f85fd2c1 upstream.
Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4db0fbb601361767144e712beb96704b966339f5 upstream.
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
Fixes: e1ee843488d5 ("usb: dwc3: gadget: Force sending delayed status during soft disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f9f59e5d74efcbaee444cf4b30ef639cc7b124e.1666146954.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c7af52c7616c3aa6dacd2336ec748d4a65df8f4 ]
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730e12fbec53ab59dd807d981a204258a4cfb29a ]
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Fixes: fcd2def66392 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
