IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 9919cce62f68e6ab68dc2a975b5dc670f8ca7d40 ]
linehandle_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linehandle_create(), where,
to verify the intent of the user, the direction must be set to in order
to effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linehandle_set_config(), but will take effect when the line value is next
get or set.
For example, by requesting a configuration with no flags set, an output
line with GPIOHANDLE_REQUEST_ACTIVE_LOW and GPIOHANDLE_REQUEST_OPEN_DRAIN
requested could have those flags cleared, inverting the sense of the line
and changing the line drive to push-pull on the next line value set.
Ensure the intent of the user by disallowing configurations which do not
have direction set, returning an error to userspace to indicate that the
configuration is invalid.
And, for clarity, use lflags, a local copy of gcnf.flags, throughout when
dealing with the requested flags, rather than a mixture of both.
Fixes: e588bb1eae31 ("gpio: add new SET_CONFIG ioctl() to gpio chardev")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa9b96e9a73e4ec1771492d0527bd5fc5ef9164 ]
Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken
DT due to any error this value can be any. Without this value validation
there can be out of chips->irqs array boundaries access in
davinci_gpio_probe().
Validate the obtained nirq value so that it won't exceed the maximum
number of IRQs per bank.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://lore.kernel.org/r/20240618144344.16943-1-amishin@t-argos.ru
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08af509efdf8dad08e972b48de0e2c2a7919ea8b upstream.
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ace0ebe5c98d66889f19e0f30e2518d0c58d0e04 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3b532ad3fbf82884a2e7e83e37c7dcdd4d1d99 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5c54a9d3c4f9c15e647b049fea401ee5258696 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61df ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97846b110ea8a94c7cc903eca21786e5 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aef4ed59705585d629e81d633a83b7d416f5fb ]
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805c74eac8cb306dc69b87b6b066ab4da77ceaf1 upstream.
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cc3542c76acb5f59001e3e562eba672f1983355 upstream.
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b3455697 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block")
Cc: stable@kernel.org
Co-developed-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d656bd259edb89dc1d9938ec5c5389867088546 ]
While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.
gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a04), so add protection for that.
Fixes: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95dd1e34ff5bbee93a28ff3947eceaf6de811b1a ]
If gpio_set_transitory() fails, we should free the GPIO again. Most
notably, the flag FLAG_REQUESTED has previously been set in
gpiod_request_commit(), and should be reset on failure.
To my knowledge, this does not affect any current users, since the
gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted
to 0. However the gpio_set_transitory() function calles the .set_config()
function of the corresponding GPIO chip and there are some GPIO drivers in
which some (unlikely) branches return other values like -EPROBE_DEFER,
and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not
be reset, which results in the pin being blocked until the next reboot.
Fixes: e10f72bf4b3e ("gpio: gpiolib: Generalise state persistence beyond sleep")
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc363413ef8ea842ae7a99e3caf5465dafdd3a49 upstream.
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Fixes: 659d8a62311f ("gpio: vf610: add imx7ulp support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e8bc2dda5a7a8e2babc9975f4b11c9a6196e490 ]
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
timbgpio_gpio_set()
--> timbgpio_update_bit()
--> spin_lock(&tgpio->lock)
<interrupt>
--> timbgpio_irq_disable()
--> spin_lock_irqsave(&tgpio->lock)
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f0575116507b981e6a810e78ce3c9040395b958b upstream.
Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.
Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9315f17bf778cb8079a29639419fcc8a41a3c84 upstream.
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26d9e5640d2130ee16df7b1fb6a908f460ab004c ]
The drivers uses a mutex and I2C bus access in its PMIC EIC chip
get implementation. This means these functions can sleep and the PMIC EIC
chip should set the can_sleep property to true.
This will ensure that a warning is printed when trying to get the
value from a context that potentially can't sleep.
Fixes: 348f3cde84ab ("gpio: Add Spreadtrum PMIC EIC driver support")
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b547b5e52a0587e6b25ea520bf2f9e03d00cbcb6 ]
If an error occurs after a successful irq_domain_add_linear() call, it
should be undone by a corresponding irq_domain_remove(), as already done
in the remove function.
Fixes: c6ce2b6bffe5 ("gpio: add TB10x GPIO driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 644ee70267a934be27370f9aa618b29af7290544 ]
Uwe Kleine-König pointed out we still have one resource leak in the mvebu
driver triggered on driver detach. Let's address it with a custom devm
action.
Fixes: 812d47889a8e ("gpio/mvebu: Use irq_domain_add_linear")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1945063eb59e64d2919cb14d54d081476d9e53bb ]
This allows to get rid of a call to pwmchip_remove() in the error path. There
is no .remove function for this driver, so this change fixes a resource leak
when a gpio-mvebu device is unbound.
Fixes: 757642f9a584 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7adc6c1069ce31ef4f606ae9c05592c80a6ab5 ]
Make tps68470_gpio_output() call tps68470_gpio_set() for output-only pins
too, so that the initial value passed to gpiod_direction_output() is
honored for these pins too.
Fixes: 275b13a65547 ("gpio: Add support for TPS68470 GPIOs")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bcb976d8feb107ff2c12caaf12ac5e70f44d5f ]
Add the missing check for platform_get_irq() and return error code
if it fails.
The returned error code will be dealed with in
builtin_platform_driver(sifive_gpio_driver) and the driver will not
be registered.
Fixes: f52d6d8b43e5 ("gpio: sifive: To get gpio irq offset from device tree data")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c00914e5438e3636f26b4f814b3297ae2a1b9ee ]
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6807d82e97e81c3209dca9448f091e1448a57 ]
The core gpiolib code is able to deal with multiple interrupt parents
for a single gpio irqchip. It however only allows a single piece
of data to be conveyed to all flow handlers (either the gpio_chip
or some other, driver-specific data).
This means that drivers have to go through some interesting dance
to find the correct context, something that isn't great in interrupt
context (see aebdc8abc9db86e2bd33070fc2f961012fff74b4 for a prime
example).
Instead, offer an optional way for a pinctrl/gpio driver to provide
an array of pointers which gets used to provide the correct context
to the flow handler.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211026175815.52703-2-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 8c00914e5438 ("gpiolib: Fix GPIO chip IRQ initialization restriction")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a1bb16e0fe6650c3841e611de374bfd5578ad70 upstream.
This driver's debugfs files have had a read operation since commit
2a9e27408e12 ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e12 ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b75c4703609a3ebaf67271813521bc0281e1ec1 ]
Add the IRQCHIP_SKIP_SET_WAKE flag since there are no special IRQ Wake
bits that can be set to enable wakeup IRQ.
Fixes: 3d9edf09d452 ("[ARM] 4457/2: davinci: GPIO support")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49765b5f4320a402fbc4ed5edfd73d87640f27c ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e52 ("gpio: add a reusable generic gpio_chip using regmap")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: linux-gpio@vger.kernel.org
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f8ecb7f85f441eb7d78ba2a4df45ee8a821934e ]
Current GPIO label is fixed, so can't distinguish different GPIO
controllers through labels. Use dev name instead.
Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37870358616ca7fdb1e90ad1cdd791655ec54414 ]
We recently added locking to this function but one error path was
over looked. Drop the lock before returning.
Fixes: e5464277625c ("gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e88a0feebb241cab0253698b2f7358b6ebec802 ]
Always configure GPIO pins which are used as interrupt source as INPUTs.
In case the default pin configuration is OUTPUT, or the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT and no interrupts are received.
Always configure the interrupt source GPIO pin as input to fix the above case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 07bd1a6cc7cbb ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5464277625c1aca5c002e0f470377cdd6816dcf ]
The driver currently performs register read-modify-write without locking
in its irqchip part, this could lead to a race condition when configuring
interrupt mode setting. Add the missing bgpio spinlock lock/unlock around
the register read-modify-write.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Fixes: 07bd1a6cc7cbb ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 694175cd8a1643cde3acb45c9294bca44a8e08e9 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdbbae241a04f387ba910b8609f95fad5f1470c7 ]
While any of the GPIO cdev syscalls is in progress, the kernel can call
gpiochip_remove() (for instance, when a USB GPIO expander is disconnected)
which will set gdev->chip to NULL after which any subsequent access will
cause a crash.
To avoid that: use an RW-semaphore in which the syscalls take it for
reading (so that we don't needlessly prohibit the user-space from calling
syscalls simultaneously) while gpiochip_remove() takes it for writing so
that it can only happen once all syscalls return.
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24ea ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d98168 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[Nick: fixed a build failure with CDEV_V1 disabled]
Co-authored-by: Nick Hainke <vincent@systemli.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4398693a9e24bcab0b99ea219073917991d0792b ]
We have several comments that start with '/**' but don't conform to the
kernel doc standard. Add proper detailed descriptions for the affected
definitions and move the docs from the forward declarations to the
struct definitions where applicable.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Stable-dep-of: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533aae7c94dbc2b14301cfd68ae7e0e90f0c8438 ]
There are several places where we can crash the kernel by requesting
lines, unbinding the GPIO device, then calling any of the system calls
relevant to the GPIO character device's annonymous file descriptors:
ioctl(), read(), poll().
While I observed it with the GPIO simulator, it will also happen for any
of the GPIO devices that can be hot-unplugged - for instance any HID GPIO
expander (e.g. CP2112).
This affects both v1 and v2 uAPI.
This fixes it partially by checking if gdev->chip is not NULL but it
doesn't entirely remedy the situation as we still have a race condition
in which another thread can remove the device after the check.
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24ea ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d98168 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cef8b5019769d46725932eeace7a383bca97905 ]
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it. In case of IOCTLs use
switch-case pattern that seems the usual in such cases.
While at it, clarify necessity of else in gpiod_direction_output()
by attaching else if to the closing curly brace on a previous line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Stable-dep-of: 533aae7c94db ("gpiolib: cdev: fix NULL-pointer dereferences")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ff545af73f759d1bd04198af8ed8577fb739fc ]
The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().
Fixes: 936ee2675eee ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fecdb9f658d9c82960c98240bc0770ade19aca ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de047d ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec851b23084b3a0af8bf0f5e51d33a8d678bdc49 ]
Here is a backtrace report about memory leak detected in
gpiochip_setup_dev():
unreferenced object 0xffff88810b406400 (size 512):
comm "python3", pid 1682, jiffies 4295346908 (age 24.090s)
backtrace:
kmalloc_trace
device_add device_private_init at drivers/base/core.c:3361
(inlined by) device_add at drivers/base/core.c:3411
cdev_device_add
gpiolib_cdev_register
gpiochip_setup_dev
gpiochip_add_data_with_key
gcdev_register() & gcdev_unregister() would call device_add() &
device_del() (no matter CONFIG_GPIO_CDEV is enabled or not) to
register/unregister device.
However, if device_add() succeeds, some resource (like
struct device_private allocated by device_private_init())
is not released by device_del().
Therefore, after device_add() succeeds by gcdev_register(), it
needs to call put_device() to release resource in the error handle
path.
Here we move forward the register of release function, and let it
release every piece of resource by put_device() instead of kfree().
While at it, fix another subtle issue, i.e. when gc->ngpio is equal
to 0, we still call kcalloc() and, in case of further error, kfree()
on the ZERO_PTR pointer, which is not NULL. It's not a bug per se,
but rather waste of the resources and potentially wrong expectation
about contents of the gdev->descs variable.
Fixes: 159f3cd92f17 ("gpiolib: Defer gpio device setup until after gpiolib initialization")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dbd1ab20509e85cd3fac9479a00c59e83c08196 ]
Several drivers read the 'ngpios' device property on their own, but
since it's defined as a standard GPIO property in the device tree bindings
anyway, it's a good candidate for generalization. If the driver didn't
set its gc->ngpio, try to read the 'ngpios' property from the GPIO
device's firmware node before bailing out.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b23084b ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5ab49cd3d6937b1818b80cb5eb09dc018ae0718 ]
Drop unneeded whitespaces and put the variables of the same type
together for consistency with the rest of the code.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b23084b ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8ea8af6c8469156ac2042d83d73f6b74eb4b4b45 upstream.
Before the split of gpio and pinctrl sections in their own driver,
rockchip_set_mux was called in pinmux_ops.gpio_set_direction for
configuring a pin in its GPIO function.
This is essential for cases where pinctrl is "bypassed" by gpio
consumers otherwise the GPIO function is not configured for the pin and
it does not work. Such was the case for the sysfs/libgpiod userspace
GPIO handling.
Let's call pinctrl_gpio_direction_input/output when setting the
direction of a GPIO so that the pinctrl core requests from the rockchip
pinctrl driver to put the pin in its GPIO function.
Fixes: 9ce9a02039de ("pinctrl/rockchip: drop the gpio related codes")
Fixes: 936ee2675eee ("gpio/rockchip: add driver for rockchip gpio")
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220930132033.4003377-3-foss+kernel@0leil.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4335417da2b8d6d9b2d4411b5f9e248e5bb2d380 ]
pwm support incompatible with Armada 80x0/70x0 API is not only in
Armada 370, but also in Armada XP, 38x and 39x. So basically every non-A8K
platform. Fix check for pwm support appropriately.
Fixes: 85b7d8abfec7 ("gpio: mvebu: add pwm support for Armada 8K/7K")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69bef19d6b9700e96285f4b4e28691cda3dcd0d1 upstream.
When running gpio test on nxp-ls1028 platform with below command
gpiomon --num-events=3 --rising-edge gpiochip1 25
There will be a warning trace as below:
Call trace:
free_irq+0x204/0x360
lineevent_free+0x64/0x70
gpio_ioctl+0x598/0x6a0
__arm64_sys_ioctl+0xb4/0x100
invoke_syscall+0x5c/0x130
......
el0t_64_sync+0x1a0/0x1a4
The reason of this issue is that calling request_threaded_irq()
function failed, and then lineevent_free() is invoked to release
the resource. Since the lineevent_state::irq was already set, so
the subsequent invocation of free_irq() would trigger the above
warning call trace. To fix this issue, set the lineevent_state::irq
after the IRQ register successfully.
Fixes: 468242724143 ("gpiolib: cdev: refactor lineevent cleanup into lineevent_free")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02743c4091ccfb246f5cdbbe3f44b152d5d12933 upstream.
If creation of software node fails, the locally allocated string
array is left unfreed. Free it on error path.
Fixes: 6fda593f3082 ("gpio: mockup: Convert to use software nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7df41a6f79dfb18ba2203f8c5f0e9c0b9b57f68 upstream.
We now remove the device's debugfs entries when unbinding the driver.
This now causes a NULL-pointer dereference on module exit because the
platform devices are unregistered *after* the global debugfs directory
has been recursively removed. Fix it by unregistering the devices first.
Fixes: 303e6da99429 ("gpio: mockup: remove gpio debugfs when remove device")
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 279c12df8d2efb28def9d037f288cbfb97c30fe2 ]
Commit e39d5ef67804 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
